stm32h7 0.16.0

Device support crates for STM32H7 devices
Documentation 
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91

///Register `PLL2DIVR1` reader
pub type R = crate::R<PLL2DIVR1rs>;
///Register `PLL2DIVR1` writer
pub type W = crate::W<PLL2DIVR1rs>;
///Field `DIVN2` reader - multiplication factor for PLL2 VCO Set and reset by software to control the multiplication factor of the VCO. These bits can be written only when the PLL is disabled (PLL2ON = PLL2RDY = 0). ..........: not used ... ... Others: wrong configurations The software must set correctly these bits to insure that the VCO output frequency is between its valid frequency range, that is: 128 to 544 MHz if PLL2VCOSEL = 0 150 to 420 MHz if PLL2VCOSEL = 1 VCO output frequency = F<sub>ref2_ck</sub> x DIVN2, when fractional value 0 has been loaded into FRACN, with DIVN2 between 8 and 420 The input frequency F<sub>ref2_ck</sub> must be between 1 and 16MHz.
pub type DIVN2_R = crate::FieldReader<u16>;
///Field `DIVN2` writer - multiplication factor for PLL2 VCO Set and reset by software to control the multiplication factor of the VCO. These bits can be written only when the PLL is disabled (PLL2ON = PLL2RDY = 0). ..........: not used ... ... Others: wrong configurations The software must set correctly these bits to insure that the VCO output frequency is between its valid frequency range, that is: 128 to 544 MHz if PLL2VCOSEL = 0 150 to 420 MHz if PLL2VCOSEL = 1 VCO output frequency = F<sub>ref2_ck</sub> x DIVN2, when fractional value 0 has been loaded into FRACN, with DIVN2 between 8 and 420 The input frequency F<sub>ref2_ck</sub> must be between 1 and 16MHz.
pub type DIVN2_W<'a, REG> = crate::FieldWriter<'a, REG, 9, u16>;
///Field `DIVP` reader - PLL2 DIVP division factor Set and reset by software to control the frequency of the pll2_p_ck clock. These bits can be written only when the PLL2DIVPEN = 0. ...
pub type DIVP_R = crate::FieldReader;
///Field `DIVP` writer - PLL2 DIVP division factor Set and reset by software to control the frequency of the pll2_p_ck clock. These bits can be written only when the PLL2DIVPEN = 0. ...
pub type DIVP_W<'a, REG> = crate::FieldWriter<'a, REG, 7>;
///Field `DIVQ` reader - PLL2 DIVQ division factor Set and reset by software to control the frequency of the pll2_q_ck clock. These bits can be written only when the PLL2DIVQEN = 0. ...
pub type DIVQ_R = crate::FieldReader;
///Field `DIVQ` writer - PLL2 DIVQ division factor Set and reset by software to control the frequency of the pll2_q_ck clock. These bits can be written only when the PLL2DIVQEN = 0. ...
pub type DIVQ_W<'a, REG> = crate::FieldWriter<'a, REG, 7>;
///Field `DIVR2` reader - PLL2 DIVR division factor Set and reset by software to control the frequency of the pll2_r_ck clock. These bits can be written only when the PLL2DIVREN = 0. ...
pub type DIVR2_R = crate::FieldReader;
///Field `DIVR2` writer - PLL2 DIVR division factor Set and reset by software to control the frequency of the pll2_r_ck clock. These bits can be written only when the PLL2DIVREN = 0. ...
pub type DIVR2_W<'a, REG> = crate::FieldWriter<'a, REG, 7>;
impl R {
    ///Bits 0:8 - multiplication factor for PLL2 VCO Set and reset by software to control the multiplication factor of the VCO. These bits can be written only when the PLL is disabled (PLL2ON = PLL2RDY = 0). ..........: not used ... ... Others: wrong configurations The software must set correctly these bits to insure that the VCO output frequency is between its valid frequency range, that is: 128 to 544 MHz if PLL2VCOSEL = 0 150 to 420 MHz if PLL2VCOSEL = 1 VCO output frequency = F<sub>ref2_ck</sub> x DIVN2, when fractional value 0 has been loaded into FRACN, with DIVN2 between 8 and 420 The input frequency F<sub>ref2_ck</sub> must be between 1 and 16MHz.
    #[inline(always)]
    pub fn divn2(&self) -> DIVN2_R {
        DIVN2_R::new((self.bits & 0x01ff) as u16)
    }
    ///Bits 9:15 - PLL2 DIVP division factor Set and reset by software to control the frequency of the pll2_p_ck clock. These bits can be written only when the PLL2DIVPEN = 0. ...
    #[inline(always)]
    pub fn divp(&self) -> DIVP_R {
        DIVP_R::new(((self.bits >> 9) & 0x7f) as u8)
    }
    ///Bits 16:22 - PLL2 DIVQ division factor Set and reset by software to control the frequency of the pll2_q_ck clock. These bits can be written only when the PLL2DIVQEN = 0. ...
    #[inline(always)]
    pub fn divq(&self) -> DIVQ_R {
        DIVQ_R::new(((self.bits >> 16) & 0x7f) as u8)
    }
    ///Bits 24:30 - PLL2 DIVR division factor Set and reset by software to control the frequency of the pll2_r_ck clock. These bits can be written only when the PLL2DIVREN = 0. ...
    #[inline(always)]
    pub fn divr2(&self) -> DIVR2_R {
        DIVR2_R::new(((self.bits >> 24) & 0x7f) as u8)
    }
}
impl core::fmt::Debug for R {
    fn fmt(&self, f: &mut core::fmt::Formatter) -> core::fmt::Result {
        f.debug_struct("PLL2DIVR1")
            .field("divn2", &self.divn2())
            .field("divp", &self.divp())
            .field("divq", &self.divq())
            .field("divr2", &self.divr2())
            .finish()
    }
}
impl W {
    ///Bits 0:8 - multiplication factor for PLL2 VCO Set and reset by software to control the multiplication factor of the VCO. These bits can be written only when the PLL is disabled (PLL2ON = PLL2RDY = 0). ..........: not used ... ... Others: wrong configurations The software must set correctly these bits to insure that the VCO output frequency is between its valid frequency range, that is: 128 to 544 MHz if PLL2VCOSEL = 0 150 to 420 MHz if PLL2VCOSEL = 1 VCO output frequency = F<sub>ref2_ck</sub> x DIVN2, when fractional value 0 has been loaded into FRACN, with DIVN2 between 8 and 420 The input frequency F<sub>ref2_ck</sub> must be between 1 and 16MHz.
    #[inline(always)]
    pub fn divn2(&mut self) -> DIVN2_W<PLL2DIVR1rs> {
        DIVN2_W::new(self, 0)
    }
    ///Bits 9:15 - PLL2 DIVP division factor Set and reset by software to control the frequency of the pll2_p_ck clock. These bits can be written only when the PLL2DIVPEN = 0. ...
    #[inline(always)]
    pub fn divp(&mut self) -> DIVP_W<PLL2DIVR1rs> {
        DIVP_W::new(self, 9)
    }
    ///Bits 16:22 - PLL2 DIVQ division factor Set and reset by software to control the frequency of the pll2_q_ck clock. These bits can be written only when the PLL2DIVQEN = 0. ...
    #[inline(always)]
    pub fn divq(&mut self) -> DIVQ_W<PLL2DIVR1rs> {
        DIVQ_W::new(self, 16)
    }
    ///Bits 24:30 - PLL2 DIVR division factor Set and reset by software to control the frequency of the pll2_r_ck clock. These bits can be written only when the PLL2DIVREN = 0. ...
    #[inline(always)]
    pub fn divr2(&mut self) -> DIVR2_W<PLL2DIVR1rs> {
        DIVR2_W::new(self, 24)
    }
}
/**RCC PLL2 dividers configuration register 1

You can [`read`](crate::Reg::read) this register and get [`pll2divr1::R`](R). You can [`reset`](crate::Reg::reset), [`write`](crate::Reg::write), [`write_with_zero`](crate::Reg::write_with_zero) this register using [`pll2divr1::W`](W). You can also [`modify`](crate::Reg::modify) this register. See [API](https://docs.rs/svd2rust/#read--modify--write-api).*/
pub struct PLL2DIVR1rs;
impl crate::RegisterSpec for PLL2DIVR1rs {
    type Ux = u32;
}
///`read()` method returns [`pll2divr1::R`](R) reader structure
impl crate::Readable for PLL2DIVR1rs {}
///`write(|w| ..)` method takes [`pll2divr1::W`](W) writer structure
impl crate::Writable for PLL2DIVR1rs {
    type Safety = crate::Unsafe;
}
///`reset()` method sets PLL2DIVR1 to value 0x0101_0280
impl crate::Resettable for PLL2DIVR1rs {
    const RESET_VALUE: u32 = 0x0101_0280;
}