stm32f1xx-hal 0.10.0

//! Uses the timer interrupt to blink a led with different frequencies.
//!
//! This assumes that a LED is connected to pc13 as is the case on the blue pill board.
//!
//! Note: Without additional hardware, PC13 should not be used to drive an LED, see page 5.1.2 of
//! the reference manual for an explanation. This is not an issue on the blue pill.

#![no_std]
#![no_main]

// you can put a breakpoint on `rust_begin_unwind` to catch panics
use panic_halt as _;

#[rtic::app(device = stm32f1xx_hal::pac)]
mod app {
    use stm32f1xx_hal::{
        gpio::{gpioc::PC13, Output, PinState, PushPull},
        pac,
        prelude::*,
        timer::{CounterMs, Event},
    };

    #[shared]
    struct Shared {}

    #[local]
    struct Local {
        led: PC13<Output<PushPull>>,
        timer_handler: CounterMs<pac::TIM1>,
    }

    #[init]
    fn init(cx: init::Context) -> (Shared, Local, init::Monotonics) {
        // Take ownership over the raw flash and rcc devices and convert them into the corresponding
        // HAL structs
        let mut flash = cx.device.FLASH.constrain();
        let rcc = cx.device.RCC.constrain();

        // Freeze the configuration of all the clocks in the system and store the frozen frequencies
        // in `clocks`
        let clocks = rcc.cfgr.freeze(&mut flash.acr);

        // Acquire the GPIOC peripheral
        let mut gpioc = cx.device.GPIOC.split();

        // Configure gpio C pin 13 as a push-pull output. The `crh` register is passed to the
        // function in order to configure the port. For pins 0-7, crl should be passed instead
        let led = gpioc
            .pc13
            .into_push_pull_output_with_state(&mut gpioc.crh, PinState::High);
        // Configure the syst timer to trigger an update every second and enables interrupt
        let mut timer = cx.device.TIM1.counter_ms(&clocks);
        timer.start(1.secs()).unwrap();
        timer.listen(Event::Update);

        // Init the static resources to use them later through RTIC
        (
            Shared {},
            Local {
                led,
                timer_handler: timer,
            },
            init::Monotonics(),
        )
    }

    // Optional.
    //
    // https://rtic.rs/dev/book/en/by-example/app_idle.html
    // > When no idle function is declared, the runtime sets the SLEEPONEXIT bit and then
    // > sends the microcontroller to sleep after running init.
    #[idle]
    fn idle(_cx: idle::Context) -> ! {
        loop {
            cortex_m::asm::wfi();
        }
    }

    #[task(binds = TIM1_UP, priority = 1, local = [led, timer_handler, led_state: bool = false, count: u8 = 0])]
    fn tick(cx: tick::Context) {
        // Depending on the application, you could want to delegate some of the work done here to
        // the idle task if you want to minimize the latency of interrupts with same priority (if
        // you have any). That could be done
        if *cx.local.led_state {
            // Uses resources managed by rtic to turn led off (on bluepill)
            cx.local.led.set_high();
            *cx.local.led_state = false;
        } else {
            cx.local.led.set_low();
            *cx.local.led_state = true;
        }
        // Count used to change the timer update frequency
        *cx.local.count += 1;

        if *cx.local.count == 4 {
            // Changes timer update frequency
            cx.local.timer_handler.start(500.millis()).unwrap();
        } else if *cx.local.count == 12 {
            cx.local.timer_handler.start(1.secs()).unwrap();
            *cx.local.count = 0;
        }

        // Clears the update flag
        cx.local.timer_handler.clear_interrupt(Event::Update);
    }
}