#[doc = r"Register block"]
#[repr(C)]
pub struct RegisterBlock {
#[doc = "0x00 - This register contains the offset value towards the start of the operational register space and the version number of the IP block"]
pub caplength_chipid: crate::Reg<caplength_chipid::CAPLENGTH_CHIPID_SPEC>,
#[doc = "0x04 - Host Controller Structural Parameters"]
pub hcsparams: crate::Reg<hcsparams::HCSPARAMS_SPEC>,
#[doc = "0x08 - Host Controller Capability Parameters"]
pub hccparams: crate::Reg<hccparams::HCCPARAMS_SPEC>,
#[doc = "0x0c - Frame Length Adjustment"]
pub fladj_frindex: crate::Reg<fladj_frindex::FLADJ_FRINDEX_SPEC>,
#[doc = "0x10 - Memory base address where ATL PTD0 is stored"]
pub atl_ptd_base_addr: crate::Reg<atl_ptd_base_addr::ATL_PTD_BASE_ADDR_SPEC>,
#[doc = "0x14 - Memory base address where ISO PTD0 is stored"]
pub iso_ptd_base_addr: crate::Reg<iso_ptd_base_addr::ISO_PTD_BASE_ADDR_SPEC>,
#[doc = "0x18 - Memory base address where INT PTD0 is stored"]
pub int_ptd_base_addr: crate::Reg<int_ptd_base_addr::INT_PTD_BASE_ADDR_SPEC>,
#[doc = "0x1c - Memory base address that indicates the start of the data payload buffers"]
pub data_payload_base_addr: crate::Reg<data_payload_base_addr::DATA_PAYLOAD_BASE_ADDR_SPEC>,
#[doc = "0x20 - USB Command register"]
pub usbcmd: crate::Reg<usbcmd::USBCMD_SPEC>,
#[doc = "0x24 - USB Interrupt Status register"]
pub usbsts: crate::Reg<usbsts::USBSTS_SPEC>,
#[doc = "0x28 - USB Interrupt Enable register"]
pub usbintr: crate::Reg<usbintr::USBINTR_SPEC>,
#[doc = "0x2c - Port Status and Control register"]
pub portsc1: crate::Reg<portsc1::PORTSC1_SPEC>,
#[doc = "0x30 - Done map for each ATL PTD"]
pub atl_ptd_done_map: crate::Reg<atl_ptd_done_map::ATL_PTD_DONE_MAP_SPEC>,
#[doc = "0x34 - Skip map for each ATL PTD"]
pub atl_ptd_skip_map: crate::Reg<atl_ptd_skip_map::ATL_PTD_SKIP_MAP_SPEC>,
#[doc = "0x38 - Done map for each ISO PTD"]
pub iso_ptd_done_map: crate::Reg<iso_ptd_done_map::ISO_PTD_DONE_MAP_SPEC>,
#[doc = "0x3c - Skip map for each ISO PTD"]
pub iso_ptd_skip_map: crate::Reg<iso_ptd_skip_map::ISO_PTD_SKIP_MAP_SPEC>,
#[doc = "0x40 - Done map for each INT PTD"]
pub int_ptd_done_map: crate::Reg<int_ptd_done_map::INT_PTD_DONE_MAP_SPEC>,
#[doc = "0x44 - Skip map for each INT PTD"]
pub int_ptd_skip_map: crate::Reg<int_ptd_skip_map::INT_PTD_SKIP_MAP_SPEC>,
#[doc = "0x48 - Marks the last PTD in the list for ISO, INT and ATL"]
pub last_ptd_inuse: crate::Reg<last_ptd_inuse::LAST_PTD_INUSE_SPEC>,
#[doc = "0x4c - Register to read/write registers in the attached USB PHY"]
pub utmiplus_ulpi_debug: crate::Reg<utmiplus_ulpi_debug::UTMIPLUS_ULPI_DEBUG_SPEC>,
#[doc = "0x50 - Controls the port if it is attached to the host block or the device block"]
pub portmode: crate::Reg<portmode::PORTMODE_SPEC>,
}
#[doc = "CAPLENGTH_CHIPID register accessor: an alias for `Reg<CAPLENGTH_CHIPID_SPEC>`"]
pub type CAPLENGTH_CHIPID = crate::Reg<caplength_chipid::CAPLENGTH_CHIPID_SPEC>;
#[doc = "This register contains the offset value towards the start of the operational register space and the version number of the IP block"]
pub mod caplength_chipid;
#[doc = "HCSPARAMS register accessor: an alias for `Reg<HCSPARAMS_SPEC>`"]
pub type HCSPARAMS = crate::Reg<hcsparams::HCSPARAMS_SPEC>;
#[doc = "Host Controller Structural Parameters"]
pub mod hcsparams;
#[doc = "HCCPARAMS register accessor: an alias for `Reg<HCCPARAMS_SPEC>`"]
pub type HCCPARAMS = crate::Reg<hccparams::HCCPARAMS_SPEC>;
#[doc = "Host Controller Capability Parameters"]
pub mod hccparams;
#[doc = "FLADJ_FRINDEX register accessor: an alias for `Reg<FLADJ_FRINDEX_SPEC>`"]
pub type FLADJ_FRINDEX = crate::Reg<fladj_frindex::FLADJ_FRINDEX_SPEC>;
#[doc = "Frame Length Adjustment"]
pub mod fladj_frindex;
#[doc = "ATL_PTD_BASE_ADDR register accessor: an alias for `Reg<ATL_PTD_BASE_ADDR_SPEC>`"]
pub type ATL_PTD_BASE_ADDR = crate::Reg<atl_ptd_base_addr::ATL_PTD_BASE_ADDR_SPEC>;
#[doc = "Memory base address where ATL PTD0 is stored"]
pub mod atl_ptd_base_addr;
#[doc = "ISO_PTD_BASE_ADDR register accessor: an alias for `Reg<ISO_PTD_BASE_ADDR_SPEC>`"]
pub type ISO_PTD_BASE_ADDR = crate::Reg<iso_ptd_base_addr::ISO_PTD_BASE_ADDR_SPEC>;
#[doc = "Memory base address where ISO PTD0 is stored"]
pub mod iso_ptd_base_addr;
#[doc = "INT_PTD_BASE_ADDR register accessor: an alias for `Reg<INT_PTD_BASE_ADDR_SPEC>`"]
pub type INT_PTD_BASE_ADDR = crate::Reg<int_ptd_base_addr::INT_PTD_BASE_ADDR_SPEC>;
#[doc = "Memory base address where INT PTD0 is stored"]
pub mod int_ptd_base_addr;
#[doc = "DATA_PAYLOAD_BASE_ADDR register accessor: an alias for `Reg<DATA_PAYLOAD_BASE_ADDR_SPEC>`"]
pub type DATA_PAYLOAD_BASE_ADDR = crate::Reg<data_payload_base_addr::DATA_PAYLOAD_BASE_ADDR_SPEC>;
#[doc = "Memory base address that indicates the start of the data payload buffers"]
pub mod data_payload_base_addr;
#[doc = "USBCMD register accessor: an alias for `Reg<USBCMD_SPEC>`"]
pub type USBCMD = crate::Reg<usbcmd::USBCMD_SPEC>;
#[doc = "USB Command register"]
pub mod usbcmd;
#[doc = "USBSTS register accessor: an alias for `Reg<USBSTS_SPEC>`"]
pub type USBSTS = crate::Reg<usbsts::USBSTS_SPEC>;
#[doc = "USB Interrupt Status register"]
pub mod usbsts;
#[doc = "USBINTR register accessor: an alias for `Reg<USBINTR_SPEC>`"]
pub type USBINTR = crate::Reg<usbintr::USBINTR_SPEC>;
#[doc = "USB Interrupt Enable register"]
pub mod usbintr;
#[doc = "PORTSC1 register accessor: an alias for `Reg<PORTSC1_SPEC>`"]
pub type PORTSC1 = crate::Reg<portsc1::PORTSC1_SPEC>;
#[doc = "Port Status and Control register"]
pub mod portsc1;
#[doc = "ATL_PTD_DONE_MAP register accessor: an alias for `Reg<ATL_PTD_DONE_MAP_SPEC>`"]
pub type ATL_PTD_DONE_MAP = crate::Reg<atl_ptd_done_map::ATL_PTD_DONE_MAP_SPEC>;
#[doc = "Done map for each ATL PTD"]
pub mod atl_ptd_done_map;
#[doc = "ATL_PTD_SKIP_MAP register accessor: an alias for `Reg<ATL_PTD_SKIP_MAP_SPEC>`"]
pub type ATL_PTD_SKIP_MAP = crate::Reg<atl_ptd_skip_map::ATL_PTD_SKIP_MAP_SPEC>;
#[doc = "Skip map for each ATL PTD"]
pub mod atl_ptd_skip_map;
#[doc = "ISO_PTD_DONE_MAP register accessor: an alias for `Reg<ISO_PTD_DONE_MAP_SPEC>`"]
pub type ISO_PTD_DONE_MAP = crate::Reg<iso_ptd_done_map::ISO_PTD_DONE_MAP_SPEC>;
#[doc = "Done map for each ISO PTD"]
pub mod iso_ptd_done_map;
#[doc = "ISO_PTD_SKIP_MAP register accessor: an alias for `Reg<ISO_PTD_SKIP_MAP_SPEC>`"]
pub type ISO_PTD_SKIP_MAP = crate::Reg<iso_ptd_skip_map::ISO_PTD_SKIP_MAP_SPEC>;
#[doc = "Skip map for each ISO PTD"]
pub mod iso_ptd_skip_map;
#[doc = "INT_PTD_DONE_MAP register accessor: an alias for `Reg<INT_PTD_DONE_MAP_SPEC>`"]
pub type INT_PTD_DONE_MAP = crate::Reg<int_ptd_done_map::INT_PTD_DONE_MAP_SPEC>;
#[doc = "Done map for each INT PTD"]
pub mod int_ptd_done_map;
#[doc = "INT_PTD_SKIP_MAP register accessor: an alias for `Reg<INT_PTD_SKIP_MAP_SPEC>`"]
pub type INT_PTD_SKIP_MAP = crate::Reg<int_ptd_skip_map::INT_PTD_SKIP_MAP_SPEC>;
#[doc = "Skip map for each INT PTD"]
pub mod int_ptd_skip_map;
#[doc = "LAST_PTD_INUSE register accessor: an alias for `Reg<LAST_PTD_INUSE_SPEC>`"]
pub type LAST_PTD_INUSE = crate::Reg<last_ptd_inuse::LAST_PTD_INUSE_SPEC>;
#[doc = "Marks the last PTD in the list for ISO, INT and ATL"]
pub mod last_ptd_inuse;
#[doc = "UTMIPLUS_ULPI_DEBUG register accessor: an alias for `Reg<UTMIPLUS_ULPI_DEBUG_SPEC>`"]
pub type UTMIPLUS_ULPI_DEBUG = crate::Reg<utmiplus_ulpi_debug::UTMIPLUS_ULPI_DEBUG_SPEC>;
#[doc = "Register to read/write registers in the attached USB PHY"]
pub mod utmiplus_ulpi_debug;
#[doc = "PORTMODE register accessor: an alias for `Reg<PORTMODE_SPEC>`"]
pub type PORTMODE = crate::Reg<portmode::PORTMODE_SPEC>;
#[doc = "Controls the port if it is attached to the host block or the device block"]
pub mod portmode;