#[doc = r"Register block"]
#[repr(C)]
pub struct RegisterBlock {
#[doc = "0x00 - Configures the low level width of the SCL clock"]
pub scl_low_period: SCL_LOW_PERIOD,
#[doc = "0x04 - Transmission setting"]
pub ctr: CTR,
#[doc = "0x08 - Describe I2C work status"]
pub sr: SR,
#[doc = "0x0c - Setting time out control for receiving data"]
pub to: TO,
#[doc = "0x10 - Local slave address setting"]
pub slave_addr: SLAVE_ADDR,
#[doc = "0x14 - FIFO status register"]
pub fifo_st: FIFO_ST,
#[doc = "0x18 - FIFO configuration register"]
pub fifo_conf: FIFO_CONF,
#[doc = "0x1c - RX FIFO read data"]
pub data: DATA,
#[doc = "0x20 - Raw interrupt status"]
pub int_raw: INT_RAW,
#[doc = "0x24 - Interrupt clear bits"]
pub int_clr: INT_CLR,
#[doc = "0x28 - Interrupt enable bits"]
pub int_ena: INT_ENA,
#[doc = "0x2c - Status of captured I2C communication events"]
pub int_status: INT_STATUS,
#[doc = "0x30 - Configures the hold time after a negative SCL edge"]
pub sda_hold: SDA_HOLD,
#[doc = "0x34 - Configures the sample time after a positive SCL edge"]
pub sda_sample: SDA_SAMPLE,
#[doc = "0x38 - Configures the high level width of the SCL clock"]
pub scl_high_period: SCL_HIGH_PERIOD,
_reserved15: [u8; 0x04],
#[doc = "0x40 - Configures the interval between pulling SDA low and pulling SCL low when the master generates a START condition"]
pub scl_start_hold: SCL_START_HOLD,
#[doc = "0x44 - Configures the interval between the positive edge of SCL and the negative edge of SDA"]
pub scl_rstart_setup: SCL_RSTART_SETUP,
#[doc = "0x48 - Configures the delay after the SCL clock edge for a stop condition"]
pub scl_stop_hold: SCL_STOP_HOLD,
#[doc = "0x4c - Configures the delay between the SDA and SCL positive edge for a stop condition"]
pub scl_stop_setup: SCL_STOP_SETUP,
#[doc = "0x50 - SCL filter configuration register"]
pub scl_filter_cfg: SCL_FILTER_CFG,
#[doc = "0x54 - SDA filter configuration register"]
pub sda_filter_cfg: SDA_FILTER_CFG,
#[doc = "0x58..0x98 - I2C command register %s"]
pub comd: [COMD; 16],
#[doc = "0x98 - SCL status time out register"]
pub scl_st_time_out: SCL_ST_TIME_OUT,
#[doc = "0x9c - SCL main status time out register"]
pub scl_main_st_time_out: SCL_MAIN_ST_TIME_OUT,
#[doc = "0xa0 - Power configuration register"]
pub scl_sp_conf: SCL_SP_CONF,
#[doc = "0xa4 - Set SCL stretch of I2C slave"]
pub scl_stretch_conf: SCL_STRETCH_CONF,
_reserved26: [u8; 0x50],
#[doc = "0xf8 - Version control register"]
pub date: DATE,
}
#[doc = "SCL_LOW_PERIOD (rw) register accessor: an alias for `Reg<SCL_LOW_PERIOD_SPEC>`"]
pub type SCL_LOW_PERIOD = crate::Reg<scl_low_period::SCL_LOW_PERIOD_SPEC>;
#[doc = "Configures the low level width of the SCL clock"]
pub mod scl_low_period;
#[doc = "CTR (rw) register accessor: an alias for `Reg<CTR_SPEC>`"]
pub type CTR = crate::Reg<ctr::CTR_SPEC>;
#[doc = "Transmission setting"]
pub mod ctr;
#[doc = "SR (r) register accessor: an alias for `Reg<SR_SPEC>`"]
pub type SR = crate::Reg<sr::SR_SPEC>;
#[doc = "Describe I2C work status"]
pub mod sr;
#[doc = "TO (rw) register accessor: an alias for `Reg<TO_SPEC>`"]
pub type TO = crate::Reg<to::TO_SPEC>;
#[doc = "Setting time out control for receiving data"]
pub mod to;
#[doc = "SLAVE_ADDR (rw) register accessor: an alias for `Reg<SLAVE_ADDR_SPEC>`"]
pub type SLAVE_ADDR = crate::Reg<slave_addr::SLAVE_ADDR_SPEC>;
#[doc = "Local slave address setting"]
pub mod slave_addr;
#[doc = "FIFO_ST (rw) register accessor: an alias for `Reg<FIFO_ST_SPEC>`"]
pub type FIFO_ST = crate::Reg<fifo_st::FIFO_ST_SPEC>;
#[doc = "FIFO status register"]
pub mod fifo_st;
#[doc = "FIFO_CONF (rw) register accessor: an alias for `Reg<FIFO_CONF_SPEC>`"]
pub type FIFO_CONF = crate::Reg<fifo_conf::FIFO_CONF_SPEC>;
#[doc = "FIFO configuration register"]
pub mod fifo_conf;
#[doc = "DATA (rw) register accessor: an alias for `Reg<DATA_SPEC>`"]
pub type DATA = crate::Reg<data::DATA_SPEC>;
#[doc = "RX FIFO read data"]
pub mod data;
#[doc = "INT_RAW (r) register accessor: an alias for `Reg<INT_RAW_SPEC>`"]
pub type INT_RAW = crate::Reg<int_raw::INT_RAW_SPEC>;
#[doc = "Raw interrupt status"]
pub mod int_raw;
#[doc = "INT_CLR (w) register accessor: an alias for `Reg<INT_CLR_SPEC>`"]
pub type INT_CLR = crate::Reg<int_clr::INT_CLR_SPEC>;
#[doc = "Interrupt clear bits"]
pub mod int_clr;
#[doc = "INT_ENA (rw) register accessor: an alias for `Reg<INT_ENA_SPEC>`"]
pub type INT_ENA = crate::Reg<int_ena::INT_ENA_SPEC>;
#[doc = "Interrupt enable bits"]
pub mod int_ena;
#[doc = "INT_STATUS (r) register accessor: an alias for `Reg<INT_STATUS_SPEC>`"]
pub type INT_STATUS = crate::Reg<int_status::INT_STATUS_SPEC>;
#[doc = "Status of captured I2C communication events"]
pub mod int_status;
#[doc = "SDA_HOLD (rw) register accessor: an alias for `Reg<SDA_HOLD_SPEC>`"]
pub type SDA_HOLD = crate::Reg<sda_hold::SDA_HOLD_SPEC>;
#[doc = "Configures the hold time after a negative SCL edge"]
pub mod sda_hold;
#[doc = "SDA_SAMPLE (rw) register accessor: an alias for `Reg<SDA_SAMPLE_SPEC>`"]
pub type SDA_SAMPLE = crate::Reg<sda_sample::SDA_SAMPLE_SPEC>;
#[doc = "Configures the sample time after a positive SCL edge"]
pub mod sda_sample;
#[doc = "SCL_HIGH_PERIOD (rw) register accessor: an alias for `Reg<SCL_HIGH_PERIOD_SPEC>`"]
pub type SCL_HIGH_PERIOD = crate::Reg<scl_high_period::SCL_HIGH_PERIOD_SPEC>;
#[doc = "Configures the high level width of the SCL clock"]
pub mod scl_high_period;
#[doc = "SCL_START_HOLD (rw) register accessor: an alias for `Reg<SCL_START_HOLD_SPEC>`"]
pub type SCL_START_HOLD = crate::Reg<scl_start_hold::SCL_START_HOLD_SPEC>;
#[doc = "Configures the interval between pulling SDA low and pulling SCL low when the master generates a START condition"]
pub mod scl_start_hold;
#[doc = "SCL_RSTART_SETUP (rw) register accessor: an alias for `Reg<SCL_RSTART_SETUP_SPEC>`"]
pub type SCL_RSTART_SETUP = crate::Reg<scl_rstart_setup::SCL_RSTART_SETUP_SPEC>;
#[doc = "Configures the interval between the positive edge of SCL and the negative edge of SDA"]
pub mod scl_rstart_setup;
#[doc = "SCL_STOP_HOLD (rw) register accessor: an alias for `Reg<SCL_STOP_HOLD_SPEC>`"]
pub type SCL_STOP_HOLD = crate::Reg<scl_stop_hold::SCL_STOP_HOLD_SPEC>;
#[doc = "Configures the delay after the SCL clock edge for a stop condition"]
pub mod scl_stop_hold;
#[doc = "SCL_STOP_SETUP (rw) register accessor: an alias for `Reg<SCL_STOP_SETUP_SPEC>`"]
pub type SCL_STOP_SETUP = crate::Reg<scl_stop_setup::SCL_STOP_SETUP_SPEC>;
#[doc = "Configures the delay between the SDA and SCL positive edge for a stop condition"]
pub mod scl_stop_setup;
#[doc = "SCL_FILTER_CFG (rw) register accessor: an alias for `Reg<SCL_FILTER_CFG_SPEC>`"]
pub type SCL_FILTER_CFG = crate::Reg<scl_filter_cfg::SCL_FILTER_CFG_SPEC>;
#[doc = "SCL filter configuration register"]
pub mod scl_filter_cfg;
#[doc = "SDA_FILTER_CFG (rw) register accessor: an alias for `Reg<SDA_FILTER_CFG_SPEC>`"]
pub type SDA_FILTER_CFG = crate::Reg<sda_filter_cfg::SDA_FILTER_CFG_SPEC>;
#[doc = "SDA filter configuration register"]
pub mod sda_filter_cfg;
#[doc = "COMD (rw) register accessor: an alias for `Reg<COMD_SPEC>`"]
pub type COMD = crate::Reg<comd::COMD_SPEC>;
#[doc = "I2C command register %s"]
pub mod comd;
#[doc = "SCL_ST_TIME_OUT (rw) register accessor: an alias for `Reg<SCL_ST_TIME_OUT_SPEC>`"]
pub type SCL_ST_TIME_OUT = crate::Reg<scl_st_time_out::SCL_ST_TIME_OUT_SPEC>;
#[doc = "SCL status time out register"]
pub mod scl_st_time_out;
#[doc = "SCL_MAIN_ST_TIME_OUT (rw) register accessor: an alias for `Reg<SCL_MAIN_ST_TIME_OUT_SPEC>`"]
pub type SCL_MAIN_ST_TIME_OUT = crate::Reg<scl_main_st_time_out::SCL_MAIN_ST_TIME_OUT_SPEC>;
#[doc = "SCL main status time out register"]
pub mod scl_main_st_time_out;
#[doc = "SCL_SP_CONF (rw) register accessor: an alias for `Reg<SCL_SP_CONF_SPEC>`"]
pub type SCL_SP_CONF = crate::Reg<scl_sp_conf::SCL_SP_CONF_SPEC>;
#[doc = "Power configuration register"]
pub mod scl_sp_conf;
#[doc = "SCL_STRETCH_CONF (rw) register accessor: an alias for `Reg<SCL_STRETCH_CONF_SPEC>`"]
pub type SCL_STRETCH_CONF = crate::Reg<scl_stretch_conf::SCL_STRETCH_CONF_SPEC>;
#[doc = "Set SCL stretch of I2C slave"]
pub mod scl_stretch_conf;
#[doc = "DATE (rw) register accessor: an alias for `Reg<DATE_SPEC>`"]
pub type DATE = crate::Reg<date::DATE_SPEC>;
#[doc = "Version control register"]
pub mod date;