Enum B6 

pub enum B6 {
    PB8(PB8<Alternate<14, PushPull>>),
    PI6(PI6<Alternate<14, PushPull>>),
    PK5(PK5<Alternate<14, PushPull>>),
}

Variants

PB8(PB8<Alternate<14, PushPull>>)

PI6(PI6<Alternate<14, PushPull>>)

PK5(PK5<Alternate<14, PushPull>>)

Trait Implementations

impl Debug for B6

fn fmt(&self, f: &mut Formatter<'_>) -> Result

Formats the value using the given formatter.

impl ExtiPin for B6

fn make_interrupt_source(&mut self, _syscfg: &mut SysCfg)

Make corresponding EXTI line sensitive to this pin

fn trigger_on_edge(&mut self, _exti: &mut EXTI, _level: Edge)

Generate interrupt on rising edge, falling edge or both

fn enable_interrupt(&mut self, _exti: &mut EXTI)

Enable external interrupts from this pin.

fn disable_interrupt(&mut self, _exti: &mut EXTI)

Disable external interrupts from this pin

fn clear_interrupt_pending_bit(&mut self)

Clear the interrupt pending bit for this pin

fn check_interrupt(&self) -> bool

Reads the interrupt pending bit for this pin

impl From<Pin<'B', 8, Alternate<14>>> for B6

fn from(p: PB8<Alternate<14, PushPull>>) -> Self

Converts to this type from the input type.

impl<MODE> From<Pin<'B', 8, MODE>> for B6

where MODE: NotAlt + PinMode,

fn from(p: PB8<MODE>) -> Self

Converts to this type from the input type.

impl From<Pin<'I', 6, Alternate<14>>> for B6

fn from(p: PI6<Alternate<14, PushPull>>) -> Self

Converts to this type from the input type.

impl<MODE> From<Pin<'I', 6, MODE>> for B6

where MODE: NotAlt + PinMode,

fn from(p: PI6<MODE>) -> Self

Converts to this type from the input type.

impl From<Pin<'K', 5, Alternate<14>>> for B6

fn from(p: PK5<Alternate<14, PushPull>>) -> Self

Converts to this type from the input type.

impl<MODE> From<Pin<'K', 5, MODE>> for B6

where MODE: NotAlt + PinMode,

fn from(p: PK5<MODE>) -> Self

Converts to this type from the input type.

impl PinPull for B6

fn set_internal_resistor(&mut self, _pull: Pull)

Set the internal pull-up and pull-down resistor

fn internal_resistor(self, resistor: Pull) -> Self

impl PinSpeed for B6

fn set_speed(&mut self, _speed: Speed)

Set pin speed

fn speed(self, speed: Speed) -> Self

impl ReadPin for B6

fn is_low(&self) -> bool

fn is_high(&self) -> bool

impl<MODE> TryFrom<B6> for PB8<MODE>

where MODE: PinMode, Alternate<14, PushPull>: PinMode,

type Error = ()

The type returned in the event of a conversion error.

fn try_from(a: B6) -> Result<Self, Self::Error>

Performs the conversion.

impl<MODE> TryFrom<B6> for PI6<MODE>

where MODE: PinMode, Alternate<14, PushPull>: PinMode,

type Error = ()

The type returned in the event of a conversion error.

fn try_from(a: B6) -> Result<Self, Self::Error>

Performs the conversion.

impl<MODE> TryFrom<B6> for PK5<MODE>

where MODE: PinMode, Alternate<14, PushPull>: PinMode,

type Error = ()

The type returned in the event of a conversion error.

fn try_from(a: B6) -> Result<Self, Self::Error>

Performs the conversion.