Enum D7 

pub enum D7 {
    PB9(PB9<Alternate<13, PushPull>>),
    PE6(PE6<Alternate<13, PushPull>>),
    PI7(PI7<Alternate<13, PushPull>>),
}

Variants

PB9(PB9<Alternate<13, PushPull>>)

PE6(PE6<Alternate<13, PushPull>>)

PI7(PI7<Alternate<13, PushPull>>)

Trait Implementations

impl Debug for D7

fn fmt(&self, f: &mut Formatter<'_>) -> Result

Formats the value using the given formatter.

impl ExtiPin for D7

fn make_interrupt_source(&mut self, _syscfg: &mut SysCfg)

Make corresponding EXTI line sensitive to this pin

fn trigger_on_edge(&mut self, _exti: &mut EXTI, _level: Edge)

Generate interrupt on rising edge, falling edge or both

fn enable_interrupt(&mut self, _exti: &mut EXTI)

Enable external interrupts from this pin.

fn disable_interrupt(&mut self, _exti: &mut EXTI)

Disable external interrupts from this pin

fn clear_interrupt_pending_bit(&mut self)

Clear the interrupt pending bit for this pin

fn check_interrupt(&self) -> bool

Reads the interrupt pending bit for this pin

impl From<Pin<'B', 9, Alternate<13>>> for D7

fn from(p: PB9<Alternate<13, PushPull>>) -> Self

Converts to this type from the input type.

impl<MODE> From<Pin<'B', 9, MODE>> for D7

where MODE: NotAlt + PinMode,

fn from(p: PB9<MODE>) -> Self

Converts to this type from the input type.

impl From<Pin<'E', 6, Alternate<13>>> for D7

fn from(p: PE6<Alternate<13, PushPull>>) -> Self

Converts to this type from the input type.

impl<MODE> From<Pin<'E', 6, MODE>> for D7

where MODE: NotAlt + PinMode,

fn from(p: PE6<MODE>) -> Self

Converts to this type from the input type.

impl From<Pin<'I', 7, Alternate<13>>> for D7

fn from(p: PI7<Alternate<13, PushPull>>) -> Self

Converts to this type from the input type.

impl<MODE> From<Pin<'I', 7, MODE>> for D7

where MODE: NotAlt + PinMode,

fn from(p: PI7<MODE>) -> Self

Converts to this type from the input type.

impl PinPull for D7

fn set_internal_resistor(&mut self, _pull: Pull)

Set the internal pull-up and pull-down resistor

fn internal_resistor(self, resistor: Pull) -> Self

impl PinSpeed for D7

fn set_speed(&mut self, _speed: Speed)

Set pin speed

fn speed(self, speed: Speed) -> Self

impl ReadPin for D7

fn is_low(&self) -> bool

fn is_high(&self) -> bool

impl<MODE> TryFrom<D7> for PB9<MODE>

where MODE: PinMode, Alternate<13, PushPull>: PinMode,

type Error = ()

The type returned in the event of a conversion error.

fn try_from(a: D7) -> Result<Self, Self::Error>

Performs the conversion.

impl<MODE> TryFrom<D7> for PE6<MODE>

where MODE: PinMode, Alternate<13, PushPull>: PinMode,

type Error = ()

The type returned in the event of a conversion error.

fn try_from(a: D7) -> Result<Self, Self::Error>

Performs the conversion.

impl<MODE> TryFrom<D7> for PI7<MODE>

where MODE: PinMode, Alternate<13, PushPull>: PinMode,

type Error = ()

The type returned in the event of a conversion error.

fn try_from(a: D7) -> Result<Self, Self::Error>

Performs the conversion.