Module esp32s3::apb_saradc::ctrl

configure apb saradc controller

Structs

CTRL_SPEC

configure apb saradc controller

R

Register CTRL reader

W

Register CTRL writer

Type Definitions

SARADC_DATA_SAR_SEL_R

Field SARADC_DATA_SAR_SEL reader - 1: sar_sel will be coded by the MSB of the 16-bit output data, in this case the resolution should not be larger than 11 bits.

SARADC_DATA_SAR_SEL_W

Field SARADC_DATA_SAR_SEL writer - 1: sar_sel will be coded by the MSB of the 16-bit output data, in this case the resolution should not be larger than 11 bits.

SARADC_DATA_TO_I2S_R

Field SARADC_DATA_TO_I2S reader - 1: I2S input data is from SAR ADC (for DMA), 0: I2S input data is from GPIO matrix

SARADC_DATA_TO_I2S_W

Field SARADC_DATA_TO_I2S writer - 1: I2S input data is from SAR ADC (for DMA), 0: I2S input data is from GPIO matrix

SARADC_SAR1_PATT_LEN_R

Field SARADC_SAR1_PATT_LEN reader - 0 ~ 15 means length 1 ~ 16

SARADC_SAR1_PATT_LEN_W

Field SARADC_SAR1_PATT_LEN writer - 0 ~ 15 means length 1 ~ 16

SARADC_SAR1_PATT_P_CLEAR_R

Field SARADC_SAR1_PATT_P_CLEAR reader - clear the pointer of pattern table for DIG ADC1 CTRL

SARADC_SAR1_PATT_P_CLEAR_W

Field SARADC_SAR1_PATT_P_CLEAR writer - clear the pointer of pattern table for DIG ADC1 CTRL

SARADC_SAR2_PATT_LEN_R

Field SARADC_SAR2_PATT_LEN reader - 0 ~ 15 means length 1 ~ 16

SARADC_SAR2_PATT_LEN_W

Field SARADC_SAR2_PATT_LEN writer - 0 ~ 15 means length 1 ~ 16

SARADC_SAR2_PATT_P_CLEAR_R

Field SARADC_SAR2_PATT_P_CLEAR reader - clear the pointer of pattern table for DIG ADC2 CTRL

SARADC_SAR2_PATT_P_CLEAR_W

Field SARADC_SAR2_PATT_P_CLEAR writer - clear the pointer of pattern table for DIG ADC2 CTRL

SARADC_SAR_CLK_DIV_R

Field SARADC_SAR_CLK_DIV reader - SAR clock divider

SARADC_SAR_CLK_DIV_W

Field SARADC_SAR_CLK_DIV writer - SAR clock divider

SARADC_SAR_CLK_GATED_R

Field SARADC_SAR_CLK_GATED reader - enable SAR CLK gate when saradc idle

SARADC_SAR_CLK_GATED_W

Field SARADC_SAR_CLK_GATED writer - enable SAR CLK gate when saradc idle

SARADC_SAR_SEL_R

Field SARADC_SAR_SEL reader - 0: SAR1, 1: SAR2, only work for single SAR mode

SARADC_SAR_SEL_W

Field SARADC_SAR_SEL writer - 0: SAR1, 1: SAR2, only work for single SAR mode

SARADC_START_FORCE_R

Field SARADC_START_FORCE reader - enable start saradc by sw

SARADC_START_FORCE_W

Field SARADC_START_FORCE writer - enable start saradc by sw

SARADC_START_R

Field SARADC_START reader - start saradc by sw

SARADC_START_W

Field SARADC_START writer - start saradc by sw

SARADC_WAIT_ARB_CYCLE_R

Field SARADC_WAIT_ARB_CYCLE reader - wait arbit signal stable after sar_done

SARADC_WAIT_ARB_CYCLE_W

Field SARADC_WAIT_ARB_CYCLE writer - wait arbit signal stable after sar_done

SARADC_WORK_MODE_R

Field SARADC_WORK_MODE reader - 0: single mode, 1: double mode, 2: alternate mode

SARADC_WORK_MODE_W

Field SARADC_WORK_MODE writer - 0: single mode, 1: double mode, 2: alternate mode

SARADC_XPD_SAR_FORCE_R

Field SARADC_XPD_SAR_FORCE reader - force option to xpd sar blocks

SARADC_XPD_SAR_FORCE_W

Field SARADC_XPD_SAR_FORCE writer - force option to xpd sar blocks