stm32h7 0.16.0

///Register `BCR%s` reader
pub type R = crate::R<BCRrs>;
///Register `BCR%s` writer
pub type W = crate::W<BCRrs>;
///Wait signal during asynchronous transfers This bit enables/disables the FMC to use the wait signal even during an asynchronous protocol.
pub use super::bcr1::ASYNCWAIT;
///Field `ASYNCWAIT` reader - Wait signal during asynchronous transfers This bit enables/disables the FMC to use the wait signal even during an asynchronous protocol.
pub use super::bcr1::ASYNCWAIT_R;
///Field `ASYNCWAIT` writer - Wait signal during asynchronous transfers This bit enables/disables the FMC to use the wait signal even during an asynchronous protocol.
pub use super::bcr1::ASYNCWAIT_W;
///Burst enable bit This bit enables/disables synchronous accesses during read operations. It is valid only for synchronous memories operating in Burst mode:
pub use super::bcr1::BURSTEN;
///Field `BURSTEN` reader - Burst enable bit This bit enables/disables synchronous accesses during read operations. It is valid only for synchronous memories operating in Burst mode:
pub use super::bcr1::BURSTEN_R;
///Field `BURSTEN` writer - Burst enable bit This bit enables/disables synchronous accesses during read operations. It is valid only for synchronous memories operating in Burst mode:
pub use super::bcr1::BURSTEN_W;
///Write burst enable For PSRAM (CRAM) operating in Burst mode, the bit enables synchronous accesses during write operations. The enable bit for synchronous read accesses is the BURSTEN bit in the FMC_BCRx register.
pub use super::bcr1::CBURSTRW;
///Field `CBURSTRW` reader - Write burst enable For PSRAM (CRAM) operating in Burst mode, the bit enables synchronous accesses during write operations. The enable bit for synchronous read accesses is the BURSTEN bit in the FMC_BCRx register.
pub use super::bcr1::CBURSTRW_R;
///Field `CBURSTRW` writer - Write burst enable For PSRAM (CRAM) operating in Burst mode, the bit enables synchronous accesses during write operations. The enable bit for synchronous read accesses is the BURSTEN bit in the FMC_BCRx register.
pub use super::bcr1::CBURSTRW_W;
///CRAM Page Size These are used for Cellular RAM 1.5 which does not allow burst access to cross the address boundaries between pages. When these bits are configured, the FMC splits automatically the burst access when the memory page size is reached (refer to memory datasheet for page size). Other configuration: reserved.
pub use super::bcr1::CPSIZE;
///Field `CPSIZE` reader - CRAM Page Size These are used for Cellular RAM 1.5 which does not allow burst access to cross the address boundaries between pages. When these bits are configured, the FMC splits automatically the burst access when the memory page size is reached (refer to memory datasheet for page size). Other configuration: reserved.
pub use super::bcr1::CPSIZE_R;
///Field `CPSIZE` writer - CRAM Page Size These are used for Cellular RAM 1.5 which does not allow burst access to cross the address boundaries between pages. When these bits are configured, the FMC splits automatically the burst access when the memory page size is reached (refer to memory datasheet for page size). Other configuration: reserved.
pub use super::bcr1::CPSIZE_W;
///Extended mode enable. This bit enables the FMC to program the write timings for asynchronous accesses inside the FMC_BWTR register, thus resulting in different timings for read and write operations. Note: When the Extended mode is disabled, the FMC can operate in Mode1 or Mode2 as follows: Mode 1 is the default mode when the SRAM/PSRAM memory type is selected (MTYP =0x0 or 0x01) Mode 2 is the default mode when the NOR memory type is selected (MTYP = 0x10).
pub use super::bcr1::EXTMOD;
///Field `EXTMOD` reader - Extended mode enable. This bit enables the FMC to program the write timings for asynchronous accesses inside the FMC_BWTR register, thus resulting in different timings for read and write operations. Note: When the Extended mode is disabled, the FMC can operate in Mode1 or Mode2 as follows: Mode 1 is the default mode when the SRAM/PSRAM memory type is selected (MTYP =0x0 or 0x01) Mode 2 is the default mode when the NOR memory type is selected (MTYP = 0x10).
pub use super::bcr1::EXTMOD_R;
///Field `EXTMOD` writer - Extended mode enable. This bit enables the FMC to program the write timings for asynchronous accesses inside the FMC_BWTR register, thus resulting in different timings for read and write operations. Note: When the Extended mode is disabled, the FMC can operate in Mode1 or Mode2 as follows: Mode 1 is the default mode when the SRAM/PSRAM memory type is selected (MTYP =0x0 or 0x01) Mode 2 is the default mode when the NOR memory type is selected (MTYP = 0x10).
pub use super::bcr1::EXTMOD_W;
///Flash access enable This bit enables NOR flash memory access operations.
pub use super::bcr1::FACCEN;
///Field `FACCEN` reader - Flash access enable This bit enables NOR flash memory access operations.
pub use super::bcr1::FACCEN_R;
///Field `FACCEN` writer - Flash access enable This bit enables NOR flash memory access operations.
pub use super::bcr1::FACCEN_W;
///Memory bank enable bit This bit enables the memory bank. After reset Bank1 is enabled, all others are disabled. Accessing a disabled bank causes an ERROR on AXI bus.
pub use super::bcr1::MBKEN;
///Field `MBKEN` reader - Memory bank enable bit This bit enables the memory bank. After reset Bank1 is enabled, all others are disabled. Accessing a disabled bank causes an ERROR on AXI bus.
pub use super::bcr1::MBKEN_R;
///Field `MBKEN` writer - Memory bank enable bit This bit enables the memory bank. After reset Bank1 is enabled, all others are disabled. Accessing a disabled bank causes an ERROR on AXI bus.
pub use super::bcr1::MBKEN_W;
///Memory type These bits define the type of external memory attached to the corresponding memory bank:
pub use super::bcr1::MTYP;
///Field `MTYP` reader - Memory type These bits define the type of external memory attached to the corresponding memory bank:
pub use super::bcr1::MTYP_R;
///Field `MTYP` writer - Memory type These bits define the type of external memory attached to the corresponding memory bank:
pub use super::bcr1::MTYP_W;
///Address/data multiplexing enable bit When this bit is set, the address and data values are multiplexed on the data bus, valid only with NOR and PSRAM memories:
pub use super::bcr1::MUXEN;
///Field `MUXEN` reader - Address/data multiplexing enable bit When this bit is set, the address and data values are multiplexed on the data bus, valid only with NOR and PSRAM memories:
pub use super::bcr1::MUXEN_R;
///Field `MUXEN` writer - Address/data multiplexing enable bit When this bit is set, the address and data values are multiplexed on the data bus, valid only with NOR and PSRAM memories:
pub use super::bcr1::MUXEN_W;
///Memory data bus width Defines the external memory device width, valid for all type of memories.
pub use super::bcr1::MWID;
///Field `MWID` reader - Memory data bus width Defines the external memory device width, valid for all type of memories.
pub use super::bcr1::MWID_R;
///Field `MWID` writer - Memory data bus width Defines the external memory device width, valid for all type of memories.
pub use super::bcr1::MWID_W;
///Wait timing configuration The NWAIT signal indicates whether the data from the memory are valid or if a wait state must be inserted when accessing the memory in Synchronous mode. This configuration bit determines if NWAIT is asserted by the memory one clock cycle before the wait state or during the wait state:
pub use super::bcr1::WAITCFG;
///Field `WAITCFG` reader - Wait timing configuration The NWAIT signal indicates whether the data from the memory are valid or if a wait state must be inserted when accessing the memory in Synchronous mode. This configuration bit determines if NWAIT is asserted by the memory one clock cycle before the wait state or during the wait state:
pub use super::bcr1::WAITCFG_R;
///Field `WAITCFG` writer - Wait timing configuration The NWAIT signal indicates whether the data from the memory are valid or if a wait state must be inserted when accessing the memory in Synchronous mode. This configuration bit determines if NWAIT is asserted by the memory one clock cycle before the wait state or during the wait state:
pub use super::bcr1::WAITCFG_W;
///Wait enable bit This bit enables/disables wait-state insertion via the NWAIT signal when accessing the memory in Synchronous mode.
pub use super::bcr1::WAITEN;
///Field `WAITEN` reader - Wait enable bit This bit enables/disables wait-state insertion via the NWAIT signal when accessing the memory in Synchronous mode.
pub use super::bcr1::WAITEN_R;
///Field `WAITEN` writer - Wait enable bit This bit enables/disables wait-state insertion via the NWAIT signal when accessing the memory in Synchronous mode.
pub use super::bcr1::WAITEN_W;
///Wait signal polarity bit This bit defines the polarity of the wait signal from memory used for either in Synchronous or Asynchronous mode:
pub use super::bcr1::WAITPOL;
///Field `WAITPOL` reader - Wait signal polarity bit This bit defines the polarity of the wait signal from memory used for either in Synchronous or Asynchronous mode:
pub use super::bcr1::WAITPOL_R;
///Field `WAITPOL` writer - Wait signal polarity bit This bit defines the polarity of the wait signal from memory used for either in Synchronous or Asynchronous mode:
pub use super::bcr1::WAITPOL_W;
///Write enable bit This bit indicates whether write operations are enabled/disabled in the bank by the FMC:
pub use super::bcr1::WREN;
///Field `WREN` reader - Write enable bit This bit indicates whether write operations are enabled/disabled in the bank by the FMC:
pub use super::bcr1::WREN_R;
///Field `WREN` writer - Write enable bit This bit indicates whether write operations are enabled/disabled in the bank by the FMC:
pub use super::bcr1::WREN_W;
impl R {
    ///Bit 0 - Memory bank enable bit This bit enables the memory bank. After reset Bank1 is enabled, all others are disabled. Accessing a disabled bank causes an ERROR on AXI bus.
    #[inline(always)]
    pub fn mbken(&self) -> MBKEN_R {
        MBKEN_R::new((self.bits & 1) != 0)
    }
    ///Bit 1 - Address/data multiplexing enable bit When this bit is set, the address and data values are multiplexed on the data bus, valid only with NOR and PSRAM memories:
    #[inline(always)]
    pub fn muxen(&self) -> MUXEN_R {
        MUXEN_R::new(((self.bits >> 1) & 1) != 0)
    }
    ///Bits 2:3 - Memory type These bits define the type of external memory attached to the corresponding memory bank:
    #[inline(always)]
    pub fn mtyp(&self) -> MTYP_R {
        MTYP_R::new(((self.bits >> 2) & 3) as u8)
    }
    ///Bits 4:5 - Memory data bus width Defines the external memory device width, valid for all type of memories.
    #[inline(always)]
    pub fn mwid(&self) -> MWID_R {
        MWID_R::new(((self.bits >> 4) & 3) as u8)
    }
    ///Bit 6 - Flash access enable This bit enables NOR flash memory access operations.
    #[inline(always)]
    pub fn faccen(&self) -> FACCEN_R {
        FACCEN_R::new(((self.bits >> 6) & 1) != 0)
    }
    ///Bit 8 - Burst enable bit This bit enables/disables synchronous accesses during read operations. It is valid only for synchronous memories operating in Burst mode:
    #[inline(always)]
    pub fn bursten(&self) -> BURSTEN_R {
        BURSTEN_R::new(((self.bits >> 8) & 1) != 0)
    }
    ///Bit 9 - Wait signal polarity bit This bit defines the polarity of the wait signal from memory used for either in Synchronous or Asynchronous mode:
    #[inline(always)]
    pub fn waitpol(&self) -> WAITPOL_R {
        WAITPOL_R::new(((self.bits >> 9) & 1) != 0)
    }
    ///Bit 11 - Wait timing configuration The NWAIT signal indicates whether the data from the memory are valid or if a wait state must be inserted when accessing the memory in Synchronous mode. This configuration bit determines if NWAIT is asserted by the memory one clock cycle before the wait state or during the wait state:
    #[inline(always)]
    pub fn waitcfg(&self) -> WAITCFG_R {
        WAITCFG_R::new(((self.bits >> 11) & 1) != 0)
    }
    ///Bit 12 - Write enable bit This bit indicates whether write operations are enabled/disabled in the bank by the FMC:
    #[inline(always)]
    pub fn wren(&self) -> WREN_R {
        WREN_R::new(((self.bits >> 12) & 1) != 0)
    }
    ///Bit 13 - Wait enable bit This bit enables/disables wait-state insertion via the NWAIT signal when accessing the memory in Synchronous mode.
    #[inline(always)]
    pub fn waiten(&self) -> WAITEN_R {
        WAITEN_R::new(((self.bits >> 13) & 1) != 0)
    }
    ///Bit 14 - Extended mode enable. This bit enables the FMC to program the write timings for asynchronous accesses inside the FMC_BWTR register, thus resulting in different timings for read and write operations. Note: When the Extended mode is disabled, the FMC can operate in Mode1 or Mode2 as follows: Mode 1 is the default mode when the SRAM/PSRAM memory type is selected (MTYP =0x0 or 0x01) Mode 2 is the default mode when the NOR memory type is selected (MTYP = 0x10).
    #[inline(always)]
    pub fn extmod(&self) -> EXTMOD_R {
        EXTMOD_R::new(((self.bits >> 14) & 1) != 0)
    }
    ///Bit 15 - Wait signal during asynchronous transfers This bit enables/disables the FMC to use the wait signal even during an asynchronous protocol.
    #[inline(always)]
    pub fn asyncwait(&self) -> ASYNCWAIT_R {
        ASYNCWAIT_R::new(((self.bits >> 15) & 1) != 0)
    }
    ///Bits 16:18 - CRAM Page Size These are used for Cellular RAM 1.5 which does not allow burst access to cross the address boundaries between pages. When these bits are configured, the FMC splits automatically the burst access when the memory page size is reached (refer to memory datasheet for page size). Other configuration: reserved.
    #[inline(always)]
    pub fn cpsize(&self) -> CPSIZE_R {
        CPSIZE_R::new(((self.bits >> 16) & 7) as u8)
    }
    ///Bit 19 - Write burst enable For PSRAM (CRAM) operating in Burst mode, the bit enables synchronous accesses during write operations. The enable bit for synchronous read accesses is the BURSTEN bit in the FMC_BCRx register.
    #[inline(always)]
    pub fn cburstrw(&self) -> CBURSTRW_R {
        CBURSTRW_R::new(((self.bits >> 19) & 1) != 0)
    }
}
impl core::fmt::Debug for R {
    fn fmt(&self, f: &mut core::fmt::Formatter) -> core::fmt::Result {
        f.debug_struct("BCR")
            .field("mbken", &self.mbken())
            .field("muxen", &self.muxen())
            .field("mtyp", &self.mtyp())
            .field("mwid", &self.mwid())
            .field("faccen", &self.faccen())
            .field("bursten", &self.bursten())
            .field("waitpol", &self.waitpol())
            .field("waitcfg", &self.waitcfg())
            .field("wren", &self.wren())
            .field("waiten", &self.waiten())
            .field("extmod", &self.extmod())
            .field("asyncwait", &self.asyncwait())
            .field("cpsize", &self.cpsize())
            .field("cburstrw", &self.cburstrw())
            .finish()
    }
}
impl W {
    ///Bit 0 - Memory bank enable bit This bit enables the memory bank. After reset Bank1 is enabled, all others are disabled. Accessing a disabled bank causes an ERROR on AXI bus.
    #[inline(always)]
    pub fn mbken(&mut self) -> MBKEN_W<BCRrs> {
        MBKEN_W::new(self, 0)
    }
    ///Bit 1 - Address/data multiplexing enable bit When this bit is set, the address and data values are multiplexed on the data bus, valid only with NOR and PSRAM memories:
    #[inline(always)]
    pub fn muxen(&mut self) -> MUXEN_W<BCRrs> {
        MUXEN_W::new(self, 1)
    }
    ///Bits 2:3 - Memory type These bits define the type of external memory attached to the corresponding memory bank:
    #[inline(always)]
    pub fn mtyp(&mut self) -> MTYP_W<BCRrs> {
        MTYP_W::new(self, 2)
    }
    ///Bits 4:5 - Memory data bus width Defines the external memory device width, valid for all type of memories.
    #[inline(always)]
    pub fn mwid(&mut self) -> MWID_W<BCRrs> {
        MWID_W::new(self, 4)
    }
    ///Bit 6 - Flash access enable This bit enables NOR flash memory access operations.
    #[inline(always)]
    pub fn faccen(&mut self) -> FACCEN_W<BCRrs> {
        FACCEN_W::new(self, 6)
    }
    ///Bit 8 - Burst enable bit This bit enables/disables synchronous accesses during read operations. It is valid only for synchronous memories operating in Burst mode:
    #[inline(always)]
    pub fn bursten(&mut self) -> BURSTEN_W<BCRrs> {
        BURSTEN_W::new(self, 8)
    }
    ///Bit 9 - Wait signal polarity bit This bit defines the polarity of the wait signal from memory used for either in Synchronous or Asynchronous mode:
    #[inline(always)]
    pub fn waitpol(&mut self) -> WAITPOL_W<BCRrs> {
        WAITPOL_W::new(self, 9)
    }
    ///Bit 11 - Wait timing configuration The NWAIT signal indicates whether the data from the memory are valid or if a wait state must be inserted when accessing the memory in Synchronous mode. This configuration bit determines if NWAIT is asserted by the memory one clock cycle before the wait state or during the wait state:
    #[inline(always)]
    pub fn waitcfg(&mut self) -> WAITCFG_W<BCRrs> {
        WAITCFG_W::new(self, 11)
    }
    ///Bit 12 - Write enable bit This bit indicates whether write operations are enabled/disabled in the bank by the FMC:
    #[inline(always)]
    pub fn wren(&mut self) -> WREN_W<BCRrs> {
        WREN_W::new(self, 12)
    }
    ///Bit 13 - Wait enable bit This bit enables/disables wait-state insertion via the NWAIT signal when accessing the memory in Synchronous mode.
    #[inline(always)]
    pub fn waiten(&mut self) -> WAITEN_W<BCRrs> {
        WAITEN_W::new(self, 13)
    }
    ///Bit 14 - Extended mode enable. This bit enables the FMC to program the write timings for asynchronous accesses inside the FMC_BWTR register, thus resulting in different timings for read and write operations. Note: When the Extended mode is disabled, the FMC can operate in Mode1 or Mode2 as follows: Mode 1 is the default mode when the SRAM/PSRAM memory type is selected (MTYP =0x0 or 0x01) Mode 2 is the default mode when the NOR memory type is selected (MTYP = 0x10).
    #[inline(always)]
    pub fn extmod(&mut self) -> EXTMOD_W<BCRrs> {
        EXTMOD_W::new(self, 14)
    }
    ///Bit 15 - Wait signal during asynchronous transfers This bit enables/disables the FMC to use the wait signal even during an asynchronous protocol.
    #[inline(always)]
    pub fn asyncwait(&mut self) -> ASYNCWAIT_W<BCRrs> {
        ASYNCWAIT_W::new(self, 15)
    }
    ///Bits 16:18 - CRAM Page Size These are used for Cellular RAM 1.5 which does not allow burst access to cross the address boundaries between pages. When these bits are configured, the FMC splits automatically the burst access when the memory page size is reached (refer to memory datasheet for page size). Other configuration: reserved.
    #[inline(always)]
    pub fn cpsize(&mut self) -> CPSIZE_W<BCRrs> {
        CPSIZE_W::new(self, 16)
    }
    ///Bit 19 - Write burst enable For PSRAM (CRAM) operating in Burst mode, the bit enables synchronous accesses during write operations. The enable bit for synchronous read accesses is the BURSTEN bit in the FMC_BCRx register.
    #[inline(always)]
    pub fn cburstrw(&mut self) -> CBURSTRW_W<BCRrs> {
        CBURSTRW_W::new(self, 19)
    }
}
/**SRAM/NOR-flash chip-select control registers for bank %s

You can [`read`](crate::Reg::read) this register and get [`bcr::R`](R). You can [`reset`](crate::Reg::reset), [`write`](crate::Reg::write), [`write_with_zero`](crate::Reg::write_with_zero) this register using [`bcr::W`](W). You can also [`modify`](crate::Reg::modify) this register. See [API](https://docs.rs/svd2rust/#read--modify--write-api).*/
pub struct BCRrs;
impl crate::RegisterSpec for BCRrs {
    type Ux = u32;
}
///`read()` method returns [`bcr::R`](R) reader structure
impl crate::Readable for BCRrs {}
///`write(|w| ..)` method takes [`bcr::W`](W) writer structure
impl crate::Writable for BCRrs {
    type Safety = crate::Unsafe;
}
///`reset()` method sets BCR%s to value 0x30d2
impl crate::Resettable for BCRrs {
    const RESET_VALUE: u32 = 0x30d2;
}