restricted system commands enabled.
**errors.tex
(./errors.tex
! Undefined control sequence.
l.2 \undefinedcs
The control sequence at the end of the top line
of your error message was never \def'ed. If you have
misspelled it (e.g., `\hobx'), type `I' and the correct
spelling (e.g., `I\hbox'). Otherwise just continue,
and I'll forget about whatever was undefined.
! Missing number, treated as zero.
<to be read again>
\relax
l.3 \count1=\relax
A number should have been here; I inserted `0'.
(If you can't figure out why I needed to see a number,
look up `weird error' in the index to The TeXbook.)
! Number too big.
l.4 \count1=9999999999
9
I can only go up to 2147483647='17777777777="7FFFFFFF,
so I'm using that number instead of yours.
! Dimension too large.
l.5 \dimen1=20000pt
I can't work with sizes bigger than about 19 feet.
Continue and I'll use the largest value I can.
! Illegal unit of measure (pt inserted).
<to be read again>
x
l.6 \dimen1=3x
x
Dimensions can be in units of em, ex, in, pt, pc,
cm, mm, dd, cc, nd, nc, bp, or sp; but yours is a new one!
I'll assume that you meant to say pt, for printer's points.
To recover gracefully from this error, it's best to
delete the erroneous units; e.g., type `2' to delete
two letters. (See Chapter 27 of The TeXbook.)
! Argument of \a has an extra }.
<inserted text>
\par
...
l.7 \def\a#1{}\a}
I've run across a `}' that doesn't seem to match anything.
For example, `\def\a#1{...}' and `\a}' would produce
this error. If you simply proceed now, the `\par' that
I've just inserted will cause me to report a runaway
argument that might be the root of the problem. But if
your `}' was spurious, just type `2' and it will go away.
Runaway argument?
! Paragraph ended before \a was complete.
<to be read again>
\par
...
l.7 \def\a#1{}\a}
I suspect you've forgotten a `}', causing me to apply this
control sequence to too much text. How can we recover?
My plan is to forget the whole thing and hope for the best.
! Too many }'s.
<recently read> }
l.7 \def\a#1{}\a}
You've closed more groups than you opened.
Such booboos are generally harmless, so keep going.
Runaway argument?
{
! Paragraph ended before \b was complete.
<to be read again>
\par
l.8 \def\b#1{}\b{\par
}
I suspect you've forgotten a `}', causing me to apply this
control sequence to too much text. How can we recover?
My plan is to forget the whole thing and hope for the best.
! Too many }'s.
l.8 \def\b#1{}\b{\par}
You've closed more groups than you opened.
Such booboos are generally harmless, so keep going.
! Use of \c doesn't match its definition.
l.9 \def\c.{}\c x
If you say, e.g., `\def\a1{...}', then you must always
put `1' after `\a', since control sequence names are
made up of letters only. The macro here has not been
followed by the required stuff, so I'm ignoring it.
! custom error.
l.10 \errmessage{custom error}
This error message was generated by an \errmessage
command, so I can't give any explicit help.
Pretend that you're Hercule Poirot: Examine all clues,
and deduce the truth by order and method.
! with help.
l.11 \errhelp{help me}\errmessage{with help}
help me
! Bad register code (70000).
<to be read again>
=
l.12 \count70000=
1
A register code must be between 0 and 65535.
I changed this one to zero.
! Extra \endgroup.
l.13 \endgroup
Things are pretty mixed up, but I think the worst is over.
! Too many }'s.
l.14 }
You've closed more groups than you opened.
Such booboos are generally harmless, so keep going.
[1.2147483647])
Output written on errors.dvi (1 page, 132 bytes).