ra4w1-pac 0.2.0

/*
DISCLAIMER
This software is supplied by Renesas Electronics Corporation and is only intended for use with Renesas products.
No other uses are authorized. This software is owned by Renesas Electronics Corporation and is protected under all
applicable laws, including copyright laws.
THIS SOFTWARE IS PROVIDED "AS IS" AND RENESAS MAKES NO WARRANTIES REGARDING THIS SOFTWARE, WHETHER EXPRESS, IMPLIED
OR STATUTORY, INCLUDING BUT NOT LIMITED TO WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
NON-INFRINGEMENT.  ALL SUCH WARRANTIES ARE EXPRESSLY DISCLAIMED.TO THE MAXIMUM EXTENT PERMITTED NOT PROHIBITED BY
LAW, NEITHER RENESAS ELECTRONICS CORPORATION NOR ANY OF ITS AFFILIATED COMPANIES SHALL BE LIABLE FOR ANY DIRECT,
INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR ANY REASON RELATED TO THIS SOFTWARE, EVEN IF RENESAS OR
ITS AFFILIATES HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
Renesas reserves the right, without notice, to make changes to this software and to discontinue the availability
of this software. By using this software, you agree to the additional terms and conditions found by accessing the
following link:
http://www.renesas.com/disclaimer

*/
// Generated from SVD 1.0, with svd2pac 0.6.0 on Thu, 24 Jul 2025 04:50:19 +0000

#![allow(clippy::identity_op)]
#![allow(clippy::module_inception)]
#![allow(clippy::derivable_impls)]
#[allow(unused_imports)]
use crate::common::sealed;
#[allow(unused_imports)]
use crate::common::*;
#[doc = r"Capacitive Touch Sensing Unit"]
unsafe impl ::core::marker::Send for super::Ctsu {}
unsafe impl ::core::marker::Sync for super::Ctsu {}
impl super::Ctsu {
    #[allow(unused)]
    #[inline(always)]
    pub(crate) const fn _svd2pac_as_ptr(&self) -> *mut u8 {
        self.ptr
    }

    #[doc = "CTSU Control Register 0"]
    #[inline(always)]
    pub const fn ctsucr0(
        &self,
    ) -> &'static crate::common::Reg<self::Ctsucr0_SPEC, crate::common::RW> {
        unsafe {
            crate::common::Reg::<self::Ctsucr0_SPEC, crate::common::RW>::from_ptr(
                self._svd2pac_as_ptr().add(0usize),
            )
        }
    }

    #[doc = "CTSU Control Register 1"]
    #[inline(always)]
    pub const fn ctsucr1(
        &self,
    ) -> &'static crate::common::Reg<self::Ctsucr1_SPEC, crate::common::RW> {
        unsafe {
            crate::common::Reg::<self::Ctsucr1_SPEC, crate::common::RW>::from_ptr(
                self._svd2pac_as_ptr().add(1usize),
            )
        }
    }

    #[doc = "CTSU Synchronous Noise Reduction Setting Register"]
    #[inline(always)]
    pub const fn ctsusdprs(
        &self,
    ) -> &'static crate::common::Reg<self::Ctsusdprs_SPEC, crate::common::RW> {
        unsafe {
            crate::common::Reg::<self::Ctsusdprs_SPEC, crate::common::RW>::from_ptr(
                self._svd2pac_as_ptr().add(2usize),
            )
        }
    }

    #[doc = "CTSU Sensor Stabilization Wait Control Register"]
    #[inline(always)]
    pub const fn ctsusst(
        &self,
    ) -> &'static crate::common::Reg<self::Ctsusst_SPEC, crate::common::RW> {
        unsafe {
            crate::common::Reg::<self::Ctsusst_SPEC, crate::common::RW>::from_ptr(
                self._svd2pac_as_ptr().add(3usize),
            )
        }
    }

    #[doc = "CTSU Measurement Channel Register 0"]
    #[inline(always)]
    pub const fn ctsumch0(
        &self,
    ) -> &'static crate::common::Reg<self::Ctsumch0_SPEC, crate::common::RW> {
        unsafe {
            crate::common::Reg::<self::Ctsumch0_SPEC, crate::common::RW>::from_ptr(
                self._svd2pac_as_ptr().add(4usize),
            )
        }
    }

    #[doc = "CTSU Measurement Channel Register 1"]
    #[inline(always)]
    pub const fn ctsumch1(
        &self,
    ) -> &'static crate::common::Reg<self::Ctsumch1_SPEC, crate::common::RW> {
        unsafe {
            crate::common::Reg::<self::Ctsumch1_SPEC, crate::common::RW>::from_ptr(
                self._svd2pac_as_ptr().add(5usize),
            )
        }
    }

    #[doc = "CTSU Channel Enable Control Register 0"]
    #[inline(always)]
    pub const fn ctsuchac0(
        &self,
    ) -> &'static crate::common::Reg<self::Ctsuchac0_SPEC, crate::common::RW> {
        unsafe {
            crate::common::Reg::<self::Ctsuchac0_SPEC, crate::common::RW>::from_ptr(
                self._svd2pac_as_ptr().add(6usize),
            )
        }
    }

    #[doc = "CTSU Channel Enable Control Register 1"]
    #[inline(always)]
    pub const fn ctsuchac1(
        &self,
    ) -> &'static crate::common::Reg<self::Ctsuchac1_SPEC, crate::common::RW> {
        unsafe {
            crate::common::Reg::<self::Ctsuchac1_SPEC, crate::common::RW>::from_ptr(
                self._svd2pac_as_ptr().add(7usize),
            )
        }
    }

    #[doc = "CTSU Channel Enable Control Register 2"]
    #[inline(always)]
    pub const fn ctsuchac2(
        &self,
    ) -> &'static crate::common::Reg<self::Ctsuchac2_SPEC, crate::common::RW> {
        unsafe {
            crate::common::Reg::<self::Ctsuchac2_SPEC, crate::common::RW>::from_ptr(
                self._svd2pac_as_ptr().add(8usize),
            )
        }
    }

    #[doc = "CTSU Channel Enable Control Register 3"]
    #[inline(always)]
    pub const fn ctsuchac3(
        &self,
    ) -> &'static crate::common::Reg<self::Ctsuchac3_SPEC, crate::common::RW> {
        unsafe {
            crate::common::Reg::<self::Ctsuchac3_SPEC, crate::common::RW>::from_ptr(
                self._svd2pac_as_ptr().add(9usize),
            )
        }
    }

    #[doc = "CTSU Channel Enable Control Register 4"]
    #[inline(always)]
    pub const fn ctsuchac4(
        &self,
    ) -> &'static crate::common::Reg<self::Ctsuchac4_SPEC, crate::common::RW> {
        unsafe {
            crate::common::Reg::<self::Ctsuchac4_SPEC, crate::common::RW>::from_ptr(
                self._svd2pac_as_ptr().add(10usize),
            )
        }
    }

    #[doc = "CTSU Channel Transmit/Receive Control Register 0"]
    #[inline(always)]
    pub const fn ctsuchtrc0(
        &self,
    ) -> &'static crate::common::Reg<self::Ctsuchtrc0_SPEC, crate::common::RW> {
        unsafe {
            crate::common::Reg::<self::Ctsuchtrc0_SPEC, crate::common::RW>::from_ptr(
                self._svd2pac_as_ptr().add(11usize),
            )
        }
    }

    #[doc = "CTSU Channel Transmit/Receive Control Register 1"]
    #[inline(always)]
    pub const fn ctsuchtrc1(
        &self,
    ) -> &'static crate::common::Reg<self::Ctsuchtrc1_SPEC, crate::common::RW> {
        unsafe {
            crate::common::Reg::<self::Ctsuchtrc1_SPEC, crate::common::RW>::from_ptr(
                self._svd2pac_as_ptr().add(12usize),
            )
        }
    }

    #[doc = "CTSU Channel Transmit/Receive Control Register 3"]
    #[inline(always)]
    pub const fn ctsuchtrc2(
        &self,
    ) -> &'static crate::common::Reg<self::Ctsuchtrc2_SPEC, crate::common::RW> {
        unsafe {
            crate::common::Reg::<self::Ctsuchtrc2_SPEC, crate::common::RW>::from_ptr(
                self._svd2pac_as_ptr().add(13usize),
            )
        }
    }

    #[doc = "CTSU Channel Transmit/Receive Control Register 3"]
    #[inline(always)]
    pub const fn ctsuchtrc3(
        &self,
    ) -> &'static crate::common::Reg<self::Ctsuchtrc3_SPEC, crate::common::RW> {
        unsafe {
            crate::common::Reg::<self::Ctsuchtrc3_SPEC, crate::common::RW>::from_ptr(
                self._svd2pac_as_ptr().add(14usize),
            )
        }
    }

    #[doc = "CTSU Channel Transmit/Receive Control Register 4"]
    #[inline(always)]
    pub const fn ctsuchtrc4(
        &self,
    ) -> &'static crate::common::Reg<self::Ctsuchtrc4_SPEC, crate::common::RW> {
        unsafe {
            crate::common::Reg::<self::Ctsuchtrc4_SPEC, crate::common::RW>::from_ptr(
                self._svd2pac_as_ptr().add(15usize),
            )
        }
    }

    #[doc = "CTSU High-Pass Noise Reduction Control Register"]
    #[inline(always)]
    pub const fn ctsudclkc(
        &self,
    ) -> &'static crate::common::Reg<self::Ctsudclkc_SPEC, crate::common::RW> {
        unsafe {
            crate::common::Reg::<self::Ctsudclkc_SPEC, crate::common::RW>::from_ptr(
                self._svd2pac_as_ptr().add(16usize),
            )
        }
    }

    #[doc = "CTSU Status Register"]
    #[inline(always)]
    pub const fn ctsust(
        &self,
    ) -> &'static crate::common::Reg<self::Ctsust_SPEC, crate::common::RW> {
        unsafe {
            crate::common::Reg::<self::Ctsust_SPEC, crate::common::RW>::from_ptr(
                self._svd2pac_as_ptr().add(17usize),
            )
        }
    }

    #[doc = "CTSU High-Pass Noise Reduction Spectrum Diffusion Control Register"]
    #[inline(always)]
    pub const fn ctsussc(
        &self,
    ) -> &'static crate::common::Reg<self::Ctsussc_SPEC, crate::common::RW> {
        unsafe {
            crate::common::Reg::<self::Ctsussc_SPEC, crate::common::RW>::from_ptr(
                self._svd2pac_as_ptr().add(18usize),
            )
        }
    }

    #[doc = "CTSU Sensor Offset Register 0"]
    #[inline(always)]
    pub const fn ctsuso0(
        &self,
    ) -> &'static crate::common::Reg<self::Ctsuso0_SPEC, crate::common::RW> {
        unsafe {
            crate::common::Reg::<self::Ctsuso0_SPEC, crate::common::RW>::from_ptr(
                self._svd2pac_as_ptr().add(20usize),
            )
        }
    }

    #[doc = "CTSU Sensor Offset Register 1"]
    #[inline(always)]
    pub const fn ctsuso1(
        &self,
    ) -> &'static crate::common::Reg<self::Ctsuso1_SPEC, crate::common::RW> {
        unsafe {
            crate::common::Reg::<self::Ctsuso1_SPEC, crate::common::RW>::from_ptr(
                self._svd2pac_as_ptr().add(22usize),
            )
        }
    }

    #[doc = "CTSU Sensor Counter"]
    #[inline(always)]
    pub const fn ctsusc(&self) -> &'static crate::common::Reg<self::Ctsusc_SPEC, crate::common::R> {
        unsafe {
            crate::common::Reg::<self::Ctsusc_SPEC, crate::common::R>::from_ptr(
                self._svd2pac_as_ptr().add(24usize),
            )
        }
    }

    #[doc = "CTSU Reference Counter"]
    #[inline(always)]
    pub const fn ctsurc(&self) -> &'static crate::common::Reg<self::Ctsurc_SPEC, crate::common::R> {
        unsafe {
            crate::common::Reg::<self::Ctsurc_SPEC, crate::common::R>::from_ptr(
                self._svd2pac_as_ptr().add(26usize),
            )
        }
    }

    #[doc = "CTSU Error Status Register"]
    #[inline(always)]
    pub const fn ctsuerrs(
        &self,
    ) -> &'static crate::common::Reg<self::Ctsuerrs_SPEC, crate::common::R> {
        unsafe {
            crate::common::Reg::<self::Ctsuerrs_SPEC, crate::common::R>::from_ptr(
                self._svd2pac_as_ptr().add(28usize),
            )
        }
    }
}
#[doc(hidden)]
#[derive(Copy, Clone, Eq, PartialEq)]
pub struct Ctsucr0_SPEC;
impl crate::sealed::RegSpec for Ctsucr0_SPEC {
    type DataType = u8;
}

#[doc = "CTSU Control Register 0"]
pub type Ctsucr0 = crate::RegValueT<Ctsucr0_SPEC>;

impl Ctsucr0 {
    #[doc = "CTSU Control Block Initialization"]
    #[inline(always)]
    pub fn ctsuinit(
        self,
    ) -> crate::common::RegisterField<
        4,
        0x1,
        1,
        0,
        ctsucr0::Ctsuinit,
        ctsucr0::Ctsuinit,
        Ctsucr0_SPEC,
        crate::common::RW,
    > {
        crate::common::RegisterField::<
            4,
            0x1,
            1,
            0,
            ctsucr0::Ctsuinit,
            ctsucr0::Ctsuinit,
            Ctsucr0_SPEC,
            crate::common::RW,
        >::from_register(self, 0)
    }

    #[doc = "CTSU Transmit Pin Control"]
    #[inline(always)]
    pub fn ctsuioc(
        self,
    ) -> crate::common::RegisterField<
        3,
        0x1,
        1,
        0,
        ctsucr0::Ctsuioc,
        ctsucr0::Ctsuioc,
        Ctsucr0_SPEC,
        crate::common::RW,
    > {
        crate::common::RegisterField::<
            3,
            0x1,
            1,
            0,
            ctsucr0::Ctsuioc,
            ctsucr0::Ctsuioc,
            Ctsucr0_SPEC,
            crate::common::RW,
        >::from_register(self, 0)
    }

    #[doc = "CTSU Wait State Power-Saving Enable"]
    #[inline(always)]
    pub fn ctsusnz(
        self,
    ) -> crate::common::RegisterField<
        2,
        0x1,
        1,
        0,
        ctsucr0::Ctsusnz,
        ctsucr0::Ctsusnz,
        Ctsucr0_SPEC,
        crate::common::RW,
    > {
        crate::common::RegisterField::<
            2,
            0x1,
            1,
            0,
            ctsucr0::Ctsusnz,
            ctsucr0::Ctsusnz,
            Ctsucr0_SPEC,
            crate::common::RW,
        >::from_register(self, 0)
    }

    #[doc = "CTSU Measurement Operation Start Trigger Select"]
    #[inline(always)]
    pub fn ctsucap(
        self,
    ) -> crate::common::RegisterField<
        1,
        0x1,
        1,
        0,
        ctsucr0::Ctsucap,
        ctsucr0::Ctsucap,
        Ctsucr0_SPEC,
        crate::common::RW,
    > {
        crate::common::RegisterField::<
            1,
            0x1,
            1,
            0,
            ctsucr0::Ctsucap,
            ctsucr0::Ctsucap,
            Ctsucr0_SPEC,
            crate::common::RW,
        >::from_register(self, 0)
    }

    #[doc = "CTSU Measurement Operation Start"]
    #[inline(always)]
    pub fn ctsustrt(
        self,
    ) -> crate::common::RegisterField<
        0,
        0x1,
        1,
        0,
        ctsucr0::Ctsustrt,
        ctsucr0::Ctsustrt,
        Ctsucr0_SPEC,
        crate::common::RW,
    > {
        crate::common::RegisterField::<
            0,
            0x1,
            1,
            0,
            ctsucr0::Ctsustrt,
            ctsucr0::Ctsustrt,
            Ctsucr0_SPEC,
            crate::common::RW,
        >::from_register(self, 0)
    }
}
impl ::core::default::Default for Ctsucr0 {
    #[inline(always)]
    fn default() -> Ctsucr0 {
        <crate::RegValueT<Ctsucr0_SPEC> as RegisterValue<_>>::new(0)
    }
}
pub mod ctsucr0 {

    #[derive(Clone, Copy, Eq, PartialEq, Ord, PartialOrd)]
    pub struct Ctsuinit_SPEC;
    pub type Ctsuinit = crate::EnumBitfieldStruct<u8, Ctsuinit_SPEC>;
    impl Ctsuinit {
        #[doc = "Writing a 0 has no effect, this bit is read as 0."]
        pub const _0: Self = Self::new(0);

        #[doc = "initializes the CTSU control block and registers."]
        pub const _1: Self = Self::new(1);
    }
    #[derive(Clone, Copy, Eq, PartialEq, Ord, PartialOrd)]
    pub struct Ctsuioc_SPEC;
    pub type Ctsuioc = crate::EnumBitfieldStruct<u8, Ctsuioc_SPEC>;
    impl Ctsuioc {
        #[doc = "Low-level output from transmit channel non-measurement pin."]
        pub const _0: Self = Self::new(0);

        #[doc = "High-level output from transmit channel non-measurement pin."]
        pub const _1: Self = Self::new(1);
    }
    #[derive(Clone, Copy, Eq, PartialEq, Ord, PartialOrd)]
    pub struct Ctsusnz_SPEC;
    pub type Ctsusnz = crate::EnumBitfieldStruct<u8, Ctsusnz_SPEC>;
    impl Ctsusnz {
        #[doc = "Power-saving function during wait state is disabled."]
        pub const _0: Self = Self::new(0);

        #[doc = "Power-saving function during wait state is enabled."]
        pub const _1: Self = Self::new(1);
    }
    #[derive(Clone, Copy, Eq, PartialEq, Ord, PartialOrd)]
    pub struct Ctsucap_SPEC;
    pub type Ctsucap = crate::EnumBitfieldStruct<u8, Ctsucap_SPEC>;
    impl Ctsucap {
        #[doc = "Software trigger."]
        pub const _0: Self = Self::new(0);

        #[doc = "External trigger."]
        pub const _1: Self = Self::new(1);
    }
    #[derive(Clone, Copy, Eq, PartialEq, Ord, PartialOrd)]
    pub struct Ctsustrt_SPEC;
    pub type Ctsustrt = crate::EnumBitfieldStruct<u8, Ctsustrt_SPEC>;
    impl Ctsustrt {
        #[doc = "Measurement operation stops."]
        pub const _0: Self = Self::new(0);

        #[doc = "Measurement operation starts."]
        pub const _1: Self = Self::new(1);
    }
}
#[doc(hidden)]
#[derive(Copy, Clone, Eq, PartialEq)]
pub struct Ctsucr1_SPEC;
impl crate::sealed::RegSpec for Ctsucr1_SPEC {
    type DataType = u8;
}

#[doc = "CTSU Control Register 1"]
pub type Ctsucr1 = crate::RegValueT<Ctsucr1_SPEC>;

impl Ctsucr1 {
    #[doc = "CTSU Measurement Mode Select"]
    #[inline(always)]
    pub fn ctsumd(
        self,
    ) -> crate::common::RegisterField<
        6,
        0x3,
        1,
        0,
        ctsucr1::Ctsumd,
        ctsucr1::Ctsumd,
        Ctsucr1_SPEC,
        crate::common::RW,
    > {
        crate::common::RegisterField::<
            6,
            0x3,
            1,
            0,
            ctsucr1::Ctsumd,
            ctsucr1::Ctsumd,
            Ctsucr1_SPEC,
            crate::common::RW,
        >::from_register(self, 0)
    }

    #[doc = "CTSU Operating Clock Select"]
    #[inline(always)]
    pub fn ctsuclk(
        self,
    ) -> crate::common::RegisterField<
        4,
        0x3,
        1,
        0,
        ctsucr1::Ctsuclk,
        ctsucr1::Ctsuclk,
        Ctsucr1_SPEC,
        crate::common::RW,
    > {
        crate::common::RegisterField::<
            4,
            0x3,
            1,
            0,
            ctsucr1::Ctsuclk,
            ctsucr1::Ctsuclk,
            Ctsucr1_SPEC,
            crate::common::RW,
        >::from_register(self, 0)
    }

    #[doc = "CTSU Power Supply Capacity Adjustment"]
    #[inline(always)]
    pub fn ctsuatune1(
        self,
    ) -> crate::common::RegisterField<
        3,
        0x1,
        1,
        0,
        ctsucr1::Ctsuatune1,
        ctsucr1::Ctsuatune1,
        Ctsucr1_SPEC,
        crate::common::RW,
    > {
        crate::common::RegisterField::<
            3,
            0x1,
            1,
            0,
            ctsucr1::Ctsuatune1,
            ctsucr1::Ctsuatune1,
            Ctsucr1_SPEC,
            crate::common::RW,
        >::from_register(self, 0)
    }

    #[doc = "CTSU Power Supply Operating Mode Setting"]
    #[inline(always)]
    pub fn ctsuatune0(
        self,
    ) -> crate::common::RegisterField<
        2,
        0x1,
        1,
        0,
        ctsucr1::Ctsuatune0,
        ctsucr1::Ctsuatune0,
        Ctsucr1_SPEC,
        crate::common::RW,
    > {
        crate::common::RegisterField::<
            2,
            0x1,
            1,
            0,
            ctsucr1::Ctsuatune0,
            ctsucr1::Ctsuatune0,
            Ctsucr1_SPEC,
            crate::common::RW,
        >::from_register(self, 0)
    }

    #[doc = "CTSU LPF Capacitance Charging Control"]
    #[inline(always)]
    pub fn ctsucsw(
        self,
    ) -> crate::common::RegisterField<
        1,
        0x1,
        1,
        0,
        ctsucr1::Ctsucsw,
        ctsucr1::Ctsucsw,
        Ctsucr1_SPEC,
        crate::common::RW,
    > {
        crate::common::RegisterField::<
            1,
            0x1,
            1,
            0,
            ctsucr1::Ctsucsw,
            ctsucr1::Ctsucsw,
            Ctsucr1_SPEC,
            crate::common::RW,
        >::from_register(self, 0)
    }

    #[doc = "CTSU Power Supply Enable"]
    #[inline(always)]
    pub fn ctsupon(
        self,
    ) -> crate::common::RegisterField<
        0,
        0x1,
        1,
        0,
        ctsucr1::Ctsupon,
        ctsucr1::Ctsupon,
        Ctsucr1_SPEC,
        crate::common::RW,
    > {
        crate::common::RegisterField::<
            0,
            0x1,
            1,
            0,
            ctsucr1::Ctsupon,
            ctsucr1::Ctsupon,
            Ctsucr1_SPEC,
            crate::common::RW,
        >::from_register(self, 0)
    }
}
impl ::core::default::Default for Ctsucr1 {
    #[inline(always)]
    fn default() -> Ctsucr1 {
        <crate::RegValueT<Ctsucr1_SPEC> as RegisterValue<_>>::new(0)
    }
}
pub mod ctsucr1 {

    #[derive(Clone, Copy, Eq, PartialEq, Ord, PartialOrd)]
    pub struct Ctsumd_SPEC;
    pub type Ctsumd = crate::EnumBitfieldStruct<u8, Ctsumd_SPEC>;
    impl Ctsumd {
        #[doc = "Self-capacitance single scan mode"]
        pub const _00: Self = Self::new(0);

        #[doc = "Self-capacitance multi-scan mode"]
        pub const _01: Self = Self::new(1);

        #[doc = "Mutual capacitance simple scan mode"]
        pub const _10: Self = Self::new(2);

        #[doc = "Mutual capacitance full scan mode"]
        pub const _11: Self = Self::new(3);
    }
    #[derive(Clone, Copy, Eq, PartialEq, Ord, PartialOrd)]
    pub struct Ctsuclk_SPEC;
    pub type Ctsuclk = crate::EnumBitfieldStruct<u8, Ctsuclk_SPEC>;
    impl Ctsuclk {
        #[doc = "PCLK"]
        pub const _00: Self = Self::new(0);

        #[doc = "PCLK/2 (PCLK divided by 2)"]
        pub const _01: Self = Self::new(1);

        #[doc = "PCLK/2 (PCLK divided by 4)"]
        pub const _10: Self = Self::new(2);

        #[doc = "Setting prohibited"]
        pub const _11: Self = Self::new(3);
    }
    #[derive(Clone, Copy, Eq, PartialEq, Ord, PartialOrd)]
    pub struct Ctsuatune1_SPEC;
    pub type Ctsuatune1 = crate::EnumBitfieldStruct<u8, Ctsuatune1_SPEC>;
    impl Ctsuatune1 {
        #[doc = "Normal output"]
        pub const _0: Self = Self::new(0);

        #[doc = "High-current output"]
        pub const _1: Self = Self::new(1);
    }
    #[derive(Clone, Copy, Eq, PartialEq, Ord, PartialOrd)]
    pub struct Ctsuatune0_SPEC;
    pub type Ctsuatune0 = crate::EnumBitfieldStruct<u8, Ctsuatune0_SPEC>;
    impl Ctsuatune0 {
        #[doc = "Normal operating mode"]
        pub const _0: Self = Self::new(0);

        #[doc = "Low-voltage operating mode"]
        pub const _1: Self = Self::new(1);
    }
    #[derive(Clone, Copy, Eq, PartialEq, Ord, PartialOrd)]
    pub struct Ctsucsw_SPEC;
    pub type Ctsucsw = crate::EnumBitfieldStruct<u8, Ctsucsw_SPEC>;
    impl Ctsucsw {
        #[doc = "Turned off capacitance switch"]
        pub const _0: Self = Self::new(0);

        #[doc = "Turned on capacitance switch"]
        pub const _1: Self = Self::new(1);
    }
    #[derive(Clone, Copy, Eq, PartialEq, Ord, PartialOrd)]
    pub struct Ctsupon_SPEC;
    pub type Ctsupon = crate::EnumBitfieldStruct<u8, Ctsupon_SPEC>;
    impl Ctsupon {
        #[doc = "Powered off the CTSU"]
        pub const _0: Self = Self::new(0);

        #[doc = "Powered on the CTSU"]
        pub const _1: Self = Self::new(1);
    }
}
#[doc(hidden)]
#[derive(Copy, Clone, Eq, PartialEq)]
pub struct Ctsusdprs_SPEC;
impl crate::sealed::RegSpec for Ctsusdprs_SPEC {
    type DataType = u8;
}

#[doc = "CTSU Synchronous Noise Reduction Setting Register"]
pub type Ctsusdprs = crate::RegValueT<Ctsusdprs_SPEC>;

impl Ctsusdprs {
    #[doc = "This bit is read as 0. The write value should be 0."]
    #[inline(always)]
    pub fn reserved(
        self,
    ) -> crate::common::RegisterFieldBool<7, 1, 0, Ctsusdprs_SPEC, crate::common::RW> {
        crate::common::RegisterFieldBool::<7,1,0,Ctsusdprs_SPEC,crate::common::RW>::from_register(self,0)
    }

    #[doc = "CTSU High-Pass Noise Reduction Function Off Setting"]
    #[inline(always)]
    pub fn ctsusoff(
        self,
    ) -> crate::common::RegisterField<
        6,
        0x1,
        1,
        0,
        ctsusdprs::Ctsusoff,
        ctsusdprs::Ctsusoff,
        Ctsusdprs_SPEC,
        crate::common::RW,
    > {
        crate::common::RegisterField::<
            6,
            0x1,
            1,
            0,
            ctsusdprs::Ctsusoff,
            ctsusdprs::Ctsusoff,
            Ctsusdprs_SPEC,
            crate::common::RW,
        >::from_register(self, 0)
    }

    #[doc = "CTSU Base Period and Pulse Count Setting"]
    #[inline(always)]
    pub fn ctsuprmode(
        self,
    ) -> crate::common::RegisterField<
        4,
        0x3,
        1,
        0,
        ctsusdprs::Ctsuprmode,
        ctsusdprs::Ctsuprmode,
        Ctsusdprs_SPEC,
        crate::common::RW,
    > {
        crate::common::RegisterField::<
            4,
            0x3,
            1,
            0,
            ctsusdprs::Ctsuprmode,
            ctsusdprs::Ctsuprmode,
            Ctsusdprs_SPEC,
            crate::common::RW,
        >::from_register(self, 0)
    }

    #[doc = "CTSU Measurement Time and Pulse Count AdjustmentRecommended setting: 3 (0011b)"]
    #[inline(always)]
    pub fn ctsuprratio(
        self,
    ) -> crate::common::RegisterField<0, 0xf, 1, 0, u8, u8, Ctsusdprs_SPEC, crate::common::RW> {
        crate::common::RegisterField::<0,0xf,1,0,u8,u8,Ctsusdprs_SPEC,crate::common::RW>::from_register(self,0)
    }
}
impl ::core::default::Default for Ctsusdprs {
    #[inline(always)]
    fn default() -> Ctsusdprs {
        <crate::RegValueT<Ctsusdprs_SPEC> as RegisterValue<_>>::new(0)
    }
}
pub mod ctsusdprs {

    #[derive(Clone, Copy, Eq, PartialEq, Ord, PartialOrd)]
    pub struct Ctsusoff_SPEC;
    pub type Ctsusoff = crate::EnumBitfieldStruct<u8, Ctsusoff_SPEC>;
    impl Ctsusoff {
        #[doc = "High-pass noise reduction function turned on"]
        pub const _0: Self = Self::new(0);

        #[doc = "High-pass noise reduction function turned off"]
        pub const _1: Self = Self::new(1);
    }
    #[derive(Clone, Copy, Eq, PartialEq, Ord, PartialOrd)]
    pub struct Ctsuprmode_SPEC;
    pub type Ctsuprmode = crate::EnumBitfieldStruct<u8, Ctsuprmode_SPEC>;
    impl Ctsuprmode {
        #[doc = "510 pulses"]
        pub const _00: Self = Self::new(0);

        #[doc = "126 pulses"]
        pub const _01: Self = Self::new(1);

        #[doc = "62 pulses (recommended setting value)"]
        pub const _10: Self = Self::new(2);

        #[doc = "Setting prohibited"]
        pub const _11: Self = Self::new(3);
    }
}
#[doc(hidden)]
#[derive(Copy, Clone, Eq, PartialEq)]
pub struct Ctsusst_SPEC;
impl crate::sealed::RegSpec for Ctsusst_SPEC {
    type DataType = u8;
}

#[doc = "CTSU Sensor Stabilization Wait Control Register"]
pub type Ctsusst = crate::RegValueT<Ctsusst_SPEC>;

impl Ctsusst {
    #[doc = "CTSU Sensor Stabilization Wait ControlNOTE: The value of these bits should be fixed to 00010000b."]
    #[inline(always)]
    pub fn ctsusst(
        self,
    ) -> crate::common::RegisterField<0, 0xff, 1, 0, u8, u8, Ctsusst_SPEC, crate::common::RW> {
        crate::common::RegisterField::<0,0xff,1,0,u8,u8,Ctsusst_SPEC,crate::common::RW>::from_register(self,0)
    }
}
impl ::core::default::Default for Ctsusst {
    #[inline(always)]
    fn default() -> Ctsusst {
        <crate::RegValueT<Ctsusst_SPEC> as RegisterValue<_>>::new(0)
    }
}

#[doc(hidden)]
#[derive(Copy, Clone, Eq, PartialEq)]
pub struct Ctsumch0_SPEC;
impl crate::sealed::RegSpec for Ctsumch0_SPEC {
    type DataType = u8;
}

#[doc = "CTSU Measurement Channel Register 0"]
pub type Ctsumch0 = crate::RegValueT<Ctsumch0_SPEC>;

impl Ctsumch0 {
    #[doc = "These bits are read as 00. The write value should be 00."]
    #[inline(always)]
    pub fn reserved(
        self,
    ) -> crate::common::RegisterField<6, 0x3, 1, 0, u8, u8, Ctsumch0_SPEC, crate::common::RW> {
        crate::common::RegisterField::<6,0x3,1,0,u8,u8,Ctsumch0_SPEC,crate::common::RW>::from_register(self,0)
    }

    #[doc = "CTSU Measurement Channel 0.Note1: Writing to these bits is only enabled in self-capacitance single-scan mode (CTSUCR1.CTSUMD\\[1:0\\] bits = 00b).Note2: If  the value of CTSUMCH0 was set to b\'111111 in  mode other than self-capacitor single scan mode, the measurement is stopped."]
    #[inline(always)]
    pub fn ctsumch0(
        self,
    ) -> crate::common::RegisterField<
        0,
        0x3f,
        1,
        0,
        ctsumch0::Ctsumch0,
        ctsumch0::Ctsumch0,
        Ctsumch0_SPEC,
        crate::common::RW,
    > {
        crate::common::RegisterField::<
            0,
            0x3f,
            1,
            0,
            ctsumch0::Ctsumch0,
            ctsumch0::Ctsumch0,
            Ctsumch0_SPEC,
            crate::common::RW,
        >::from_register(self, 0)
    }
}
impl ::core::default::Default for Ctsumch0 {
    #[inline(always)]
    fn default() -> Ctsumch0 {
        <crate::RegValueT<Ctsumch0_SPEC> as RegisterValue<_>>::new(63)
    }
}
pub mod ctsumch0 {

    #[derive(Clone, Copy, Eq, PartialEq, Ord, PartialOrd)]
    pub struct Ctsumch0_SPEC;
    pub type Ctsumch0 = crate::EnumBitfieldStruct<u8, Ctsumch0_SPEC>;
    impl Ctsumch0 {
        #[doc = "The value of CTSUMCH0 indicate to channel to be measured."]
        pub const CTSUMCH_0: Self = Self::new(0);
    }
}
#[doc(hidden)]
#[derive(Copy, Clone, Eq, PartialEq)]
pub struct Ctsumch1_SPEC;
impl crate::sealed::RegSpec for Ctsumch1_SPEC {
    type DataType = u8;
}

#[doc = "CTSU Measurement Channel Register 1"]
pub type Ctsumch1 = crate::RegValueT<Ctsumch1_SPEC>;

impl Ctsumch1 {
    #[doc = "These bits are read as 00. The write value should be 00."]
    #[inline(always)]
    pub fn reserved(
        self,
    ) -> crate::common::RegisterField<6, 0x3, 1, 0, u8, u8, Ctsumch1_SPEC, crate::common::RW> {
        crate::common::RegisterField::<6,0x3,1,0,u8,u8,Ctsumch1_SPEC,crate::common::RW>::from_register(self,0)
    }

    #[doc = "CTSU Measurement Channel 1Note1: If  the value of CTSUMCH1 was set to b\'111111, the measurement is stopped."]
    #[inline(always)]
    pub fn ctsumch1(
        self,
    ) -> crate::common::RegisterField<
        0,
        0x3f,
        1,
        0,
        ctsumch1::Ctsumch1,
        ctsumch1::Ctsumch1,
        Ctsumch1_SPEC,
        crate::common::R,
    > {
        crate::common::RegisterField::<
            0,
            0x3f,
            1,
            0,
            ctsumch1::Ctsumch1,
            ctsumch1::Ctsumch1,
            Ctsumch1_SPEC,
            crate::common::R,
        >::from_register(self, 0)
    }
}
impl ::core::default::Default for Ctsumch1 {
    #[inline(always)]
    fn default() -> Ctsumch1 {
        <crate::RegValueT<Ctsumch1_SPEC> as RegisterValue<_>>::new(63)
    }
}
pub mod ctsumch1 {

    #[derive(Clone, Copy, Eq, PartialEq, Ord, PartialOrd)]
    pub struct Ctsumch1_SPEC;
    pub type Ctsumch1 = crate::EnumBitfieldStruct<u8, Ctsumch1_SPEC>;
    impl Ctsumch1 {
        #[doc = "The value of CTSUMCH1 indicate to channel to be measured."]
        pub const CTSUMCH_1: Self = Self::new(0);
    }
}
#[doc(hidden)]
#[derive(Copy, Clone, Eq, PartialEq)]
pub struct Ctsuchac0_SPEC;
impl crate::sealed::RegSpec for Ctsuchac0_SPEC {
    type DataType = u8;
}

#[doc = "CTSU Channel Enable Control Register 0"]
pub type Ctsuchac0 = crate::RegValueT<Ctsuchac0_SPEC>;

impl Ctsuchac0 {
    #[doc = "CTSU Channel Enable Control 0.0: Not measurement target1: Measurement targetNote: CTSUCHAC0\\[0\\] corresponds to TS00 and CTSUCHAC0\\[7\\] corresponds to TS07. but the write value of CTSUCHAC0\\[2\\] should be 0."]
    #[inline(always)]
    pub fn ctsuchac0(
        self,
    ) -> crate::common::RegisterField<
        0,
        0xff,
        1,
        0,
        ctsuchac0::Ctsuchac0,
        ctsuchac0::Ctsuchac0,
        Ctsuchac0_SPEC,
        crate::common::RW,
    > {
        crate::common::RegisterField::<
            0,
            0xff,
            1,
            0,
            ctsuchac0::Ctsuchac0,
            ctsuchac0::Ctsuchac0,
            Ctsuchac0_SPEC,
            crate::common::RW,
        >::from_register(self, 0)
    }
}
impl ::core::default::Default for Ctsuchac0 {
    #[inline(always)]
    fn default() -> Ctsuchac0 {
        <crate::RegValueT<Ctsuchac0_SPEC> as RegisterValue<_>>::new(0)
    }
}
pub mod ctsuchac0 {

    #[derive(Clone, Copy, Eq, PartialEq, Ord, PartialOrd)]
    pub struct Ctsuchac0_SPEC;
    pub type Ctsuchac0 = crate::EnumBitfieldStruct<u8, Ctsuchac0_SPEC>;
    impl Ctsuchac0 {
        #[doc = "TS pin which correspond to the bit number of CTSUCHAC0 register set whether the measurement target."]
        pub const CTSUCHAC_0: Self = Self::new(0);
    }
}
#[doc(hidden)]
#[derive(Copy, Clone, Eq, PartialEq)]
pub struct Ctsuchac1_SPEC;
impl crate::sealed::RegSpec for Ctsuchac1_SPEC {
    type DataType = u8;
}

#[doc = "CTSU Channel Enable Control Register 1"]
pub type Ctsuchac1 = crate::RegValueT<Ctsuchac1_SPEC>;

impl Ctsuchac1 {
    #[doc = "CTSU Channel Enable Control 1.0: Not measurement target1: Measurement targetNote: CTSUCHAC1\\[0\\] corresponds to TS08 and CTSUCHAC1\\[7\\] corresponds to TS15."]
    #[inline(always)]
    pub fn ctsuchac1(
        self,
    ) -> crate::common::RegisterField<
        0,
        0xff,
        1,
        0,
        ctsuchac1::Ctsuchac1,
        ctsuchac1::Ctsuchac1,
        Ctsuchac1_SPEC,
        crate::common::RW,
    > {
        crate::common::RegisterField::<
            0,
            0xff,
            1,
            0,
            ctsuchac1::Ctsuchac1,
            ctsuchac1::Ctsuchac1,
            Ctsuchac1_SPEC,
            crate::common::RW,
        >::from_register(self, 0)
    }
}
impl ::core::default::Default for Ctsuchac1 {
    #[inline(always)]
    fn default() -> Ctsuchac1 {
        <crate::RegValueT<Ctsuchac1_SPEC> as RegisterValue<_>>::new(0)
    }
}
pub mod ctsuchac1 {

    #[derive(Clone, Copy, Eq, PartialEq, Ord, PartialOrd)]
    pub struct Ctsuchac1_SPEC;
    pub type Ctsuchac1 = crate::EnumBitfieldStruct<u8, Ctsuchac1_SPEC>;
    impl Ctsuchac1 {
        #[doc = "TS pin which correspond to the bit number of CTSUCHAC1 register set whether the measurement target."]
        pub const CTSUCHAC_1: Self = Self::new(0);
    }
}
#[doc(hidden)]
#[derive(Copy, Clone, Eq, PartialEq)]
pub struct Ctsuchac2_SPEC;
impl crate::sealed::RegSpec for Ctsuchac2_SPEC {
    type DataType = u8;
}

#[doc = "CTSU Channel Enable Control Register 2"]
pub type Ctsuchac2 = crate::RegValueT<Ctsuchac2_SPEC>;

impl Ctsuchac2 {
    #[doc = "CTSU Channel Enable Control 2.0: Not measurement target1: Measurement targetNote: CTSUCHAC2\\[0\\] corresponds to TS16 and CTSUCHAC2\\[7\\] corresponds to TS23."]
    #[inline(always)]
    pub fn ctsuchac2(
        self,
    ) -> crate::common::RegisterField<
        0,
        0xff,
        1,
        0,
        ctsuchac2::Ctsuchac2,
        ctsuchac2::Ctsuchac2,
        Ctsuchac2_SPEC,
        crate::common::RW,
    > {
        crate::common::RegisterField::<
            0,
            0xff,
            1,
            0,
            ctsuchac2::Ctsuchac2,
            ctsuchac2::Ctsuchac2,
            Ctsuchac2_SPEC,
            crate::common::RW,
        >::from_register(self, 0)
    }
}
impl ::core::default::Default for Ctsuchac2 {
    #[inline(always)]
    fn default() -> Ctsuchac2 {
        <crate::RegValueT<Ctsuchac2_SPEC> as RegisterValue<_>>::new(0)
    }
}
pub mod ctsuchac2 {

    #[derive(Clone, Copy, Eq, PartialEq, Ord, PartialOrd)]
    pub struct Ctsuchac2_SPEC;
    pub type Ctsuchac2 = crate::EnumBitfieldStruct<u8, Ctsuchac2_SPEC>;
    impl Ctsuchac2 {
        #[doc = "TS pin which correspond to the bit number of CTSUCHAC2 register set whether the measurement target."]
        pub const CTSUCHAC_2: Self = Self::new(0);
    }
}
#[doc(hidden)]
#[derive(Copy, Clone, Eq, PartialEq)]
pub struct Ctsuchac3_SPEC;
impl crate::sealed::RegSpec for Ctsuchac3_SPEC {
    type DataType = u8;
}

#[doc = "CTSU Channel Enable Control Register 3"]
pub type Ctsuchac3 = crate::RegValueT<Ctsuchac3_SPEC>;

impl Ctsuchac3 {
    #[doc = "CTSU Channel Enable Control 3.0: Not measurement target1: Measurement targetNote: CTSUCHAC3\\[0\\] corresponds to TS24 and CTSUCHAC3\\[7\\] corresponds to TS31."]
    #[inline(always)]
    pub fn ctsuchac3(
        self,
    ) -> crate::common::RegisterField<
        0,
        0xff,
        1,
        0,
        ctsuchac3::Ctsuchac3,
        ctsuchac3::Ctsuchac3,
        Ctsuchac3_SPEC,
        crate::common::RW,
    > {
        crate::common::RegisterField::<
            0,
            0xff,
            1,
            0,
            ctsuchac3::Ctsuchac3,
            ctsuchac3::Ctsuchac3,
            Ctsuchac3_SPEC,
            crate::common::RW,
        >::from_register(self, 0)
    }
}
impl ::core::default::Default for Ctsuchac3 {
    #[inline(always)]
    fn default() -> Ctsuchac3 {
        <crate::RegValueT<Ctsuchac3_SPEC> as RegisterValue<_>>::new(0)
    }
}
pub mod ctsuchac3 {

    #[derive(Clone, Copy, Eq, PartialEq, Ord, PartialOrd)]
    pub struct Ctsuchac3_SPEC;
    pub type Ctsuchac3 = crate::EnumBitfieldStruct<u8, Ctsuchac3_SPEC>;
    impl Ctsuchac3 {
        #[doc = "TS pin which correspond to the bit number of CTSUCHAC3 register set whether the measurement target."]
        pub const CTSUCHAC_3: Self = Self::new(0);
    }
}
#[doc(hidden)]
#[derive(Copy, Clone, Eq, PartialEq)]
pub struct Ctsuchac4_SPEC;
impl crate::sealed::RegSpec for Ctsuchac4_SPEC {
    type DataType = u8;
}

#[doc = "CTSU Channel Enable Control Register 4"]
pub type Ctsuchac4 = crate::RegValueT<Ctsuchac4_SPEC>;

impl Ctsuchac4 {
    #[doc = "These bits are read as 0000. The write value should be 0000."]
    #[inline(always)]
    pub fn reserved(
        self,
    ) -> crate::common::RegisterField<4, 0xf, 1, 0, u8, u8, Ctsuchac4_SPEC, crate::common::RW> {
        crate::common::RegisterField::<4,0xf,1,0,u8,u8,Ctsuchac4_SPEC,crate::common::RW>::from_register(self,0)
    }

    #[doc = "CTSU Channel Enable Control 4.0: Not measurement target1: Measurement targetNote: CTSUCHAC4\\[0\\] corresponds to TS32 and CTSUCHAC4\\[3\\] corresponds to TS35.  but the write value of CTSUCHAC0\\[4\\],CTSUCHAC4\\[5\\],CTSUCHAC4\\[6\\],CTSUCHAC4\\[7\\] should be 0."]
    #[inline(always)]
    pub fn ctsuchac4(
        self,
    ) -> crate::common::RegisterField<
        0,
        0xf,
        1,
        0,
        ctsuchac4::Ctsuchac4,
        ctsuchac4::Ctsuchac4,
        Ctsuchac4_SPEC,
        crate::common::RW,
    > {
        crate::common::RegisterField::<
            0,
            0xf,
            1,
            0,
            ctsuchac4::Ctsuchac4,
            ctsuchac4::Ctsuchac4,
            Ctsuchac4_SPEC,
            crate::common::RW,
        >::from_register(self, 0)
    }
}
impl ::core::default::Default for Ctsuchac4 {
    #[inline(always)]
    fn default() -> Ctsuchac4 {
        <crate::RegValueT<Ctsuchac4_SPEC> as RegisterValue<_>>::new(0)
    }
}
pub mod ctsuchac4 {

    #[derive(Clone, Copy, Eq, PartialEq, Ord, PartialOrd)]
    pub struct Ctsuchac4_SPEC;
    pub type Ctsuchac4 = crate::EnumBitfieldStruct<u8, Ctsuchac4_SPEC>;
    impl Ctsuchac4 {
        #[doc = "TS pin which correspond to the bit number of CTSUCHAC4 register set whether the measurement target."]
        pub const CTSUCHAC_4: Self = Self::new(0);
    }
}
#[doc(hidden)]
#[derive(Copy, Clone, Eq, PartialEq)]
pub struct Ctsuchtrc0_SPEC;
impl crate::sealed::RegSpec for Ctsuchtrc0_SPEC {
    type DataType = u8;
}

#[doc = "CTSU Channel Transmit/Receive Control Register 0"]
pub type Ctsuchtrc0 = crate::RegValueT<Ctsuchtrc0_SPEC>;

impl Ctsuchtrc0 {
    #[doc = "CTSU Channel Transmit/Receive Control 0"]
    #[inline(always)]
    pub fn ctsuchtrc0(
        self,
    ) -> crate::common::RegisterField<
        0,
        0xff,
        1,
        0,
        ctsuchtrc0::Ctsuchtrc0,
        ctsuchtrc0::Ctsuchtrc0,
        Ctsuchtrc0_SPEC,
        crate::common::RW,
    > {
        crate::common::RegisterField::<
            0,
            0xff,
            1,
            0,
            ctsuchtrc0::Ctsuchtrc0,
            ctsuchtrc0::Ctsuchtrc0,
            Ctsuchtrc0_SPEC,
            crate::common::RW,
        >::from_register(self, 0)
    }
}
impl ::core::default::Default for Ctsuchtrc0 {
    #[inline(always)]
    fn default() -> Ctsuchtrc0 {
        <crate::RegValueT<Ctsuchtrc0_SPEC> as RegisterValue<_>>::new(0)
    }
}
pub mod ctsuchtrc0 {

    #[derive(Clone, Copy, Eq, PartialEq, Ord, PartialOrd)]
    pub struct Ctsuchtrc0_SPEC;
    pub type Ctsuchtrc0 = crate::EnumBitfieldStruct<u8, Ctsuchtrc0_SPEC>;
    impl Ctsuchtrc0 {
        #[doc = "Reception"]
        pub const _0: Self = Self::new(0);

        #[doc = "Transmission"]
        pub const _1: Self = Self::new(1);
    }
}
#[doc(hidden)]
#[derive(Copy, Clone, Eq, PartialEq)]
pub struct Ctsuchtrc1_SPEC;
impl crate::sealed::RegSpec for Ctsuchtrc1_SPEC {
    type DataType = u8;
}

#[doc = "CTSU Channel Transmit/Receive Control Register 1"]
pub type Ctsuchtrc1 = crate::RegValueT<Ctsuchtrc1_SPEC>;

impl Ctsuchtrc1 {
    #[doc = "CTSU Channel Transmit/Receive Control 1"]
    #[inline(always)]
    pub fn ctsuchtrc1(
        self,
    ) -> crate::common::RegisterField<
        0,
        0xff,
        1,
        0,
        ctsuchtrc1::Ctsuchtrc1,
        ctsuchtrc1::Ctsuchtrc1,
        Ctsuchtrc1_SPEC,
        crate::common::RW,
    > {
        crate::common::RegisterField::<
            0,
            0xff,
            1,
            0,
            ctsuchtrc1::Ctsuchtrc1,
            ctsuchtrc1::Ctsuchtrc1,
            Ctsuchtrc1_SPEC,
            crate::common::RW,
        >::from_register(self, 0)
    }
}
impl ::core::default::Default for Ctsuchtrc1 {
    #[inline(always)]
    fn default() -> Ctsuchtrc1 {
        <crate::RegValueT<Ctsuchtrc1_SPEC> as RegisterValue<_>>::new(0)
    }
}
pub mod ctsuchtrc1 {

    #[derive(Clone, Copy, Eq, PartialEq, Ord, PartialOrd)]
    pub struct Ctsuchtrc1_SPEC;
    pub type Ctsuchtrc1 = crate::EnumBitfieldStruct<u8, Ctsuchtrc1_SPEC>;
    impl Ctsuchtrc1 {
        #[doc = "Reception"]
        pub const _0: Self = Self::new(0);

        #[doc = "Transmission"]
        pub const _1: Self = Self::new(1);
    }
}
#[doc(hidden)]
#[derive(Copy, Clone, Eq, PartialEq)]
pub struct Ctsuchtrc2_SPEC;
impl crate::sealed::RegSpec for Ctsuchtrc2_SPEC {
    type DataType = u8;
}

#[doc = "CTSU Channel Transmit/Receive Control Register 3"]
pub type Ctsuchtrc2 = crate::RegValueT<Ctsuchtrc2_SPEC>;

impl Ctsuchtrc2 {
    #[doc = "CTSU Channel Transmit/Receive Control 2"]
    #[inline(always)]
    pub fn ctsuchtrc2(
        self,
    ) -> crate::common::RegisterField<
        0,
        0xff,
        1,
        0,
        ctsuchtrc2::Ctsuchtrc2,
        ctsuchtrc2::Ctsuchtrc2,
        Ctsuchtrc2_SPEC,
        crate::common::RW,
    > {
        crate::common::RegisterField::<
            0,
            0xff,
            1,
            0,
            ctsuchtrc2::Ctsuchtrc2,
            ctsuchtrc2::Ctsuchtrc2,
            Ctsuchtrc2_SPEC,
            crate::common::RW,
        >::from_register(self, 0)
    }
}
impl ::core::default::Default for Ctsuchtrc2 {
    #[inline(always)]
    fn default() -> Ctsuchtrc2 {
        <crate::RegValueT<Ctsuchtrc2_SPEC> as RegisterValue<_>>::new(0)
    }
}
pub mod ctsuchtrc2 {

    #[derive(Clone, Copy, Eq, PartialEq, Ord, PartialOrd)]
    pub struct Ctsuchtrc2_SPEC;
    pub type Ctsuchtrc2 = crate::EnumBitfieldStruct<u8, Ctsuchtrc2_SPEC>;
    impl Ctsuchtrc2 {
        #[doc = "Reception"]
        pub const _0: Self = Self::new(0);

        #[doc = "Transmission"]
        pub const _1: Self = Self::new(1);
    }
}
#[doc(hidden)]
#[derive(Copy, Clone, Eq, PartialEq)]
pub struct Ctsuchtrc3_SPEC;
impl crate::sealed::RegSpec for Ctsuchtrc3_SPEC {
    type DataType = u8;
}

#[doc = "CTSU Channel Transmit/Receive Control Register 3"]
pub type Ctsuchtrc3 = crate::RegValueT<Ctsuchtrc3_SPEC>;

impl Ctsuchtrc3 {
    #[doc = "CTSU Channel Transmit/Receive Control 3"]
    #[inline(always)]
    pub fn ctsuchtrc3(
        self,
    ) -> crate::common::RegisterField<
        0,
        0xff,
        1,
        0,
        ctsuchtrc3::Ctsuchtrc3,
        ctsuchtrc3::Ctsuchtrc3,
        Ctsuchtrc3_SPEC,
        crate::common::RW,
    > {
        crate::common::RegisterField::<
            0,
            0xff,
            1,
            0,
            ctsuchtrc3::Ctsuchtrc3,
            ctsuchtrc3::Ctsuchtrc3,
            Ctsuchtrc3_SPEC,
            crate::common::RW,
        >::from_register(self, 0)
    }
}
impl ::core::default::Default for Ctsuchtrc3 {
    #[inline(always)]
    fn default() -> Ctsuchtrc3 {
        <crate::RegValueT<Ctsuchtrc3_SPEC> as RegisterValue<_>>::new(0)
    }
}
pub mod ctsuchtrc3 {

    #[derive(Clone, Copy, Eq, PartialEq, Ord, PartialOrd)]
    pub struct Ctsuchtrc3_SPEC;
    pub type Ctsuchtrc3 = crate::EnumBitfieldStruct<u8, Ctsuchtrc3_SPEC>;
    impl Ctsuchtrc3 {
        #[doc = "Reception"]
        pub const _0: Self = Self::new(0);

        #[doc = "Transmission"]
        pub const _1: Self = Self::new(1);
    }
}
#[doc(hidden)]
#[derive(Copy, Clone, Eq, PartialEq)]
pub struct Ctsuchtrc4_SPEC;
impl crate::sealed::RegSpec for Ctsuchtrc4_SPEC {
    type DataType = u8;
}

#[doc = "CTSU Channel Transmit/Receive Control Register 4"]
pub type Ctsuchtrc4 = crate::RegValueT<Ctsuchtrc4_SPEC>;

impl Ctsuchtrc4 {
    #[doc = "These bits are read as 0000. The write value should be 0000."]
    #[inline(always)]
    pub fn reserved(
        self,
    ) -> crate::common::RegisterField<4, 0xf, 1, 0, u8, u8, Ctsuchtrc4_SPEC, crate::common::RW>
    {
        crate::common::RegisterField::<4,0xf,1,0,u8,u8,Ctsuchtrc4_SPEC,crate::common::RW>::from_register(self,0)
    }

    #[doc = "CTSU Channel Transmit/Receive Control 4"]
    #[inline(always)]
    pub fn ctsuchac4(
        self,
    ) -> crate::common::RegisterField<
        0,
        0xf,
        1,
        0,
        ctsuchtrc4::Ctsuchac4,
        ctsuchtrc4::Ctsuchac4,
        Ctsuchtrc4_SPEC,
        crate::common::RW,
    > {
        crate::common::RegisterField::<
            0,
            0xf,
            1,
            0,
            ctsuchtrc4::Ctsuchac4,
            ctsuchtrc4::Ctsuchac4,
            Ctsuchtrc4_SPEC,
            crate::common::RW,
        >::from_register(self, 0)
    }
}
impl ::core::default::Default for Ctsuchtrc4 {
    #[inline(always)]
    fn default() -> Ctsuchtrc4 {
        <crate::RegValueT<Ctsuchtrc4_SPEC> as RegisterValue<_>>::new(0)
    }
}
pub mod ctsuchtrc4 {

    #[derive(Clone, Copy, Eq, PartialEq, Ord, PartialOrd)]
    pub struct Ctsuchac4_SPEC;
    pub type Ctsuchac4 = crate::EnumBitfieldStruct<u8, Ctsuchac4_SPEC>;
    impl Ctsuchac4 {
        #[doc = "Reception"]
        pub const _0: Self = Self::new(0);

        #[doc = "Transmission"]
        pub const _1: Self = Self::new(1);
    }
}
#[doc(hidden)]
#[derive(Copy, Clone, Eq, PartialEq)]
pub struct Ctsudclkc_SPEC;
impl crate::sealed::RegSpec for Ctsudclkc_SPEC {
    type DataType = u8;
}

#[doc = "CTSU High-Pass Noise Reduction Control Register"]
pub type Ctsudclkc = crate::RegValueT<Ctsudclkc_SPEC>;

impl Ctsudclkc {
    #[doc = "CTSU Diffusion Clock Mode ControlNOTE: This bit  should be set to 11b."]
    #[inline(always)]
    pub fn ctsusscnt(
        self,
    ) -> crate::common::RegisterField<4, 0x3, 1, 0, u8, u8, Ctsudclkc_SPEC, crate::common::RW> {
        crate::common::RegisterField::<4,0x3,1,0,u8,u8,Ctsudclkc_SPEC,crate::common::RW>::from_register(self,0)
    }

    #[doc = "These bits are read as 00. The write value should be 00."]
    #[inline(always)]
    pub fn reserved(
        self,
    ) -> crate::common::RegisterField<2, 0x3, 1, 0, u8, u8, Ctsudclkc_SPEC, crate::common::RW> {
        crate::common::RegisterField::<2,0x3,1,0,u8,u8,Ctsudclkc_SPEC,crate::common::RW>::from_register(self,0)
    }

    #[doc = "CTSU Diffusion Clock Mode SelectNOTE: This bit  should be set to 00b."]
    #[inline(always)]
    pub fn ctsussmod(
        self,
    ) -> crate::common::RegisterField<0, 0x3, 1, 0, u8, u8, Ctsudclkc_SPEC, crate::common::RW> {
        crate::common::RegisterField::<0,0x3,1,0,u8,u8,Ctsudclkc_SPEC,crate::common::RW>::from_register(self,0)
    }
}
impl ::core::default::Default for Ctsudclkc {
    #[inline(always)]
    fn default() -> Ctsudclkc {
        <crate::RegValueT<Ctsudclkc_SPEC> as RegisterValue<_>>::new(0)
    }
}

#[doc(hidden)]
#[derive(Copy, Clone, Eq, PartialEq)]
pub struct Ctsust_SPEC;
impl crate::sealed::RegSpec for Ctsust_SPEC {
    type DataType = u8;
}

#[doc = "CTSU Status Register"]
pub type Ctsust = crate::RegValueT<Ctsust_SPEC>;

impl Ctsust {
    #[doc = "CTSU Mutual Capacitance Status Flag"]
    #[inline(always)]
    pub fn ctsups(
        self,
    ) -> crate::common::RegisterField<
        7,
        0x1,
        1,
        0,
        ctsust::Ctsups,
        ctsust::Ctsups,
        Ctsust_SPEC,
        crate::common::R,
    > {
        crate::common::RegisterField::<
            7,
            0x1,
            1,
            0,
            ctsust::Ctsups,
            ctsust::Ctsups,
            Ctsust_SPEC,
            crate::common::R,
        >::from_register(self, 0)
    }

    #[doc = "CTSU Reference Counter Overflow Flag"]
    #[inline(always)]
    pub fn ctsurovf(
        self,
    ) -> crate::common::RegisterField<
        6,
        0x1,
        1,
        0,
        ctsust::Ctsurovf,
        ctsust::Ctsurovf,
        Ctsust_SPEC,
        crate::common::RW,
    > {
        crate::common::RegisterField::<
            6,
            0x1,
            1,
            0,
            ctsust::Ctsurovf,
            ctsust::Ctsurovf,
            Ctsust_SPEC,
            crate::common::RW,
        >::from_register(self, 0)
    }

    #[doc = "CTSU Sensor Counter Overflow Flag"]
    #[inline(always)]
    pub fn ctsusovf(
        self,
    ) -> crate::common::RegisterField<
        5,
        0x1,
        1,
        0,
        ctsust::Ctsusovf,
        ctsust::Ctsusovf,
        Ctsust_SPEC,
        crate::common::RW,
    > {
        crate::common::RegisterField::<
            5,
            0x1,
            1,
            0,
            ctsust::Ctsusovf,
            ctsust::Ctsusovf,
            Ctsust_SPEC,
            crate::common::RW,
        >::from_register(self, 0)
    }

    #[doc = "CTSU Data Transfer Status Flag"]
    #[inline(always)]
    pub fn ctsudtsr(
        self,
    ) -> crate::common::RegisterField<
        4,
        0x1,
        1,
        0,
        ctsust::Ctsudtsr,
        ctsust::Ctsudtsr,
        Ctsust_SPEC,
        crate::common::R,
    > {
        crate::common::RegisterField::<
            4,
            0x1,
            1,
            0,
            ctsust::Ctsudtsr,
            ctsust::Ctsudtsr,
            Ctsust_SPEC,
            crate::common::R,
        >::from_register(self, 0)
    }

    #[doc = "This bit is read as 0. The write value should be 0."]
    #[inline(always)]
    pub fn reserved(
        self,
    ) -> crate::common::RegisterFieldBool<3, 1, 0, Ctsust_SPEC, crate::common::RW> {
        crate::common::RegisterFieldBool::<3, 1, 0, Ctsust_SPEC, crate::common::RW>::from_register(
            self, 0,
        )
    }

    #[doc = "CTSU Measurement Status Counter"]
    #[inline(always)]
    pub fn ctsustc(
        self,
    ) -> crate::common::RegisterField<
        0,
        0x7,
        1,
        0,
        ctsust::Ctsustc,
        ctsust::Ctsustc,
        Ctsust_SPEC,
        crate::common::RW,
    > {
        crate::common::RegisterField::<
            0,
            0x7,
            1,
            0,
            ctsust::Ctsustc,
            ctsust::Ctsustc,
            Ctsust_SPEC,
            crate::common::RW,
        >::from_register(self, 0)
    }
}
impl ::core::default::Default for Ctsust {
    #[inline(always)]
    fn default() -> Ctsust {
        <crate::RegValueT<Ctsust_SPEC> as RegisterValue<_>>::new(0)
    }
}
pub mod ctsust {

    #[derive(Clone, Copy, Eq, PartialEq, Ord, PartialOrd)]
    pub struct Ctsups_SPEC;
    pub type Ctsups = crate::EnumBitfieldStruct<u8, Ctsups_SPEC>;
    impl Ctsups {
        #[doc = "First measurement"]
        pub const _0: Self = Self::new(0);

        #[doc = "Second measurement"]
        pub const _1: Self = Self::new(1);
    }
    #[derive(Clone, Copy, Eq, PartialEq, Ord, PartialOrd)]
    pub struct Ctsurovf_SPEC;
    pub type Ctsurovf = crate::EnumBitfieldStruct<u8, Ctsurovf_SPEC>;
    impl Ctsurovf {
        #[doc = "No overflow"]
        pub const _0: Self = Self::new(0);

        #[doc = "An overflow"]
        pub const _1: Self = Self::new(1);
    }
    #[derive(Clone, Copy, Eq, PartialEq, Ord, PartialOrd)]
    pub struct Ctsusovf_SPEC;
    pub type Ctsusovf = crate::EnumBitfieldStruct<u8, Ctsusovf_SPEC>;
    impl Ctsusovf {
        #[doc = "No overflow"]
        pub const _0: Self = Self::new(0);

        #[doc = "An overflow"]
        pub const _1: Self = Self::new(1);
    }
    #[derive(Clone, Copy, Eq, PartialEq, Ord, PartialOrd)]
    pub struct Ctsudtsr_SPEC;
    pub type Ctsudtsr = crate::EnumBitfieldStruct<u8, Ctsudtsr_SPEC>;
    impl Ctsudtsr {
        #[doc = "Measurement result has been read"]
        pub const _0: Self = Self::new(0);

        #[doc = "Measurement result has not been read"]
        pub const _1: Self = Self::new(1);
    }
    #[derive(Clone, Copy, Eq, PartialEq, Ord, PartialOrd)]
    pub struct Ctsustc_SPEC;
    pub type Ctsustc = crate::EnumBitfieldStruct<u8, Ctsustc_SPEC>;
    impl Ctsustc {
        #[doc = "Status 0"]
        pub const _000: Self = Self::new(0);

        #[doc = "Status 1"]
        pub const _001: Self = Self::new(1);

        #[doc = "Status 2"]
        pub const _010: Self = Self::new(2);

        #[doc = "Status 3"]
        pub const _011: Self = Self::new(3);

        #[doc = "Status 4"]
        pub const _100: Self = Self::new(4);

        #[doc = "Status 5"]
        pub const _101: Self = Self::new(5);
    }
}
#[doc(hidden)]
#[derive(Copy, Clone, Eq, PartialEq)]
pub struct Ctsussc_SPEC;
impl crate::sealed::RegSpec for Ctsussc_SPEC {
    type DataType = u16;
}

#[doc = "CTSU High-Pass Noise Reduction Spectrum Diffusion Control Register"]
pub type Ctsussc = crate::RegValueT<Ctsussc_SPEC>;

impl Ctsussc {
    #[doc = "CTSU Spectrum Diffusion Frequency Division Setting"]
    #[inline(always)]
    pub fn ctsussdiv(
        self,
    ) -> crate::common::RegisterField<
        8,
        0xf,
        1,
        0,
        ctsussc::Ctsussdiv,
        ctsussc::Ctsussdiv,
        Ctsussc_SPEC,
        crate::common::RW,
    > {
        crate::common::RegisterField::<
            8,
            0xf,
            1,
            0,
            ctsussc::Ctsussdiv,
            ctsussc::Ctsussdiv,
            Ctsussc_SPEC,
            crate::common::RW,
        >::from_register(self, 0)
    }

    #[doc = "These bits are read as 00000000. The write value should be 00000000."]
    #[inline(always)]
    pub fn reserved(
        self,
    ) -> crate::common::RegisterField<0, 0xff, 1, 0, u8, u8, Ctsussc_SPEC, crate::common::RW> {
        crate::common::RegisterField::<0,0xff,1,0,u8,u8,Ctsussc_SPEC,crate::common::RW>::from_register(self,0)
    }
}
impl ::core::default::Default for Ctsussc {
    #[inline(always)]
    fn default() -> Ctsussc {
        <crate::RegValueT<Ctsussc_SPEC> as RegisterValue<_>>::new(0)
    }
}
pub mod ctsussc {

    #[derive(Clone, Copy, Eq, PartialEq, Ord, PartialOrd)]
    pub struct Ctsussdiv_SPEC;
    pub type Ctsussdiv = crate::EnumBitfieldStruct<u8, Ctsussdiv_SPEC>;
    impl Ctsussdiv {
        #[doc = "4.00 <= fb"]
        pub const _0000: Self = Self::new(0);

        #[doc = "2.00 <= fb < 4.00"]
        pub const _0001: Self = Self::new(1);

        #[doc = "1.33 <= fb < 2.00"]
        pub const _0010: Self = Self::new(2);

        #[doc = "1.00 <= fb < 1.33"]
        pub const _0011: Self = Self::new(3);

        #[doc = "0.80 <= fb < 1.00"]
        pub const _0100: Self = Self::new(4);

        #[doc = "0.67 <= fb < 0.80"]
        pub const _0101: Self = Self::new(5);

        #[doc = "0.57 <= fb < 0.67"]
        pub const _0110: Self = Self::new(6);

        #[doc = "0.50 <= fb < 0.57"]
        pub const _0111: Self = Self::new(7);

        #[doc = "0.44 <= fb < 0.50"]
        pub const _1000: Self = Self::new(8);

        #[doc = "0.40 <= fb < 0.44"]
        pub const _1001: Self = Self::new(9);

        #[doc = "0.36 <= fb < 0.40"]
        pub const _1010: Self = Self::new(10);

        #[doc = "0.33 <= fb < 0.36"]
        pub const _1011: Self = Self::new(11);

        #[doc = "0.31 <= fb < 0.33"]
        pub const _1100: Self = Self::new(12);

        #[doc = "0.29 <= fb < 0.31"]
        pub const _1101: Self = Self::new(13);

        #[doc = "0.27 <= fb < 0.29"]
        pub const _1110: Self = Self::new(14);

        #[doc = "fb < 0.27"]
        pub const _1111: Self = Self::new(15);
    }
}
#[doc(hidden)]
#[derive(Copy, Clone, Eq, PartialEq)]
pub struct Ctsuso0_SPEC;
impl crate::sealed::RegSpec for Ctsuso0_SPEC {
    type DataType = u16;
}

#[doc = "CTSU Sensor Offset Register 0"]
pub type Ctsuso0 = crate::RegValueT<Ctsuso0_SPEC>;

impl Ctsuso0 {
    #[doc = "CTSU Measurement Count Setting"]
    #[inline(always)]
    pub fn ctsusnum(
        self,
    ) -> crate::common::RegisterField<10, 0x3f, 1, 0, u8, u8, Ctsuso0_SPEC, crate::common::RW> {
        crate::common::RegisterField::<10,0x3f,1,0,u8,u8,Ctsuso0_SPEC,crate::common::RW>::from_register(self,0)
    }

    #[doc = "CTSU Sensor Offset AdjustmentCurrent offset amount is CTSUSO ( 0 to 1023 )"]
    #[inline(always)]
    pub fn ctsuso(
        self,
    ) -> crate::common::RegisterField<0, 0x3ff, 1, 0, u16, u16, Ctsuso0_SPEC, crate::common::RW>
    {
        crate::common::RegisterField::<0,0x3ff,1,0,u16,u16,Ctsuso0_SPEC,crate::common::RW>::from_register(self,0)
    }
}
impl ::core::default::Default for Ctsuso0 {
    #[inline(always)]
    fn default() -> Ctsuso0 {
        <crate::RegValueT<Ctsuso0_SPEC> as RegisterValue<_>>::new(0)
    }
}

#[doc(hidden)]
#[derive(Copy, Clone, Eq, PartialEq)]
pub struct Ctsuso1_SPEC;
impl crate::sealed::RegSpec for Ctsuso1_SPEC {
    type DataType = u16;
}

#[doc = "CTSU Sensor Offset Register 1"]
pub type Ctsuso1 = crate::RegValueT<Ctsuso1_SPEC>;

impl Ctsuso1 {
    #[doc = "This bit is read as 0. The write value should be 0."]
    #[inline(always)]
    pub fn reserved(
        self,
    ) -> crate::common::RegisterFieldBool<15, 1, 0, Ctsuso1_SPEC, crate::common::RW> {
        crate::common::RegisterFieldBool::<15, 1, 0, Ctsuso1_SPEC, crate::common::RW>::from_register(
            self, 0,
        )
    }

    #[doc = "CTSU ICO Gain Adjustment"]
    #[inline(always)]
    pub fn ctsuicog(
        self,
    ) -> crate::common::RegisterField<
        13,
        0x3,
        1,
        0,
        ctsuso1::Ctsuicog,
        ctsuso1::Ctsuicog,
        Ctsuso1_SPEC,
        crate::common::RW,
    > {
        crate::common::RegisterField::<
            13,
            0x3,
            1,
            0,
            ctsuso1::Ctsuicog,
            ctsuso1::Ctsuicog,
            Ctsuso1_SPEC,
            crate::common::RW,
        >::from_register(self, 0)
    }

    #[doc = "CTSU Base Clock SettingOperating clock divided by ( CTSUSDPA + 1 ) x 2"]
    #[inline(always)]
    pub fn ctsusdpa(
        self,
    ) -> crate::common::RegisterField<8, 0x1f, 1, 0, u8, u8, Ctsuso1_SPEC, crate::common::RW> {
        crate::common::RegisterField::<8,0x1f,1,0,u8,u8,Ctsuso1_SPEC,crate::common::RW>::from_register(self,0)
    }

    #[doc = "CTSU Reference ICO Current AdjustmentCurrent offset amount is CTSUSO ( 0 to 255 )"]
    #[inline(always)]
    pub fn ctsuricoa(
        self,
    ) -> crate::common::RegisterField<0, 0xff, 1, 0, u8, u8, Ctsuso1_SPEC, crate::common::RW> {
        crate::common::RegisterField::<0,0xff,1,0,u8,u8,Ctsuso1_SPEC,crate::common::RW>::from_register(self,0)
    }
}
impl ::core::default::Default for Ctsuso1 {
    #[inline(always)]
    fn default() -> Ctsuso1 {
        <crate::RegValueT<Ctsuso1_SPEC> as RegisterValue<_>>::new(0)
    }
}
pub mod ctsuso1 {

    #[derive(Clone, Copy, Eq, PartialEq, Ord, PartialOrd)]
    pub struct Ctsuicog_SPEC;
    pub type Ctsuicog = crate::EnumBitfieldStruct<u8, Ctsuicog_SPEC>;
    impl Ctsuicog {
        #[doc = "100 percent gain"]
        pub const _00: Self = Self::new(0);

        #[doc = "66 percent gain"]
        pub const _01: Self = Self::new(1);

        #[doc = "50 percent gain"]
        pub const _10: Self = Self::new(2);

        #[doc = "40 percent gain"]
        pub const _11: Self = Self::new(3);
    }
}
#[doc(hidden)]
#[derive(Copy, Clone, Eq, PartialEq)]
pub struct Ctsusc_SPEC;
impl crate::sealed::RegSpec for Ctsusc_SPEC {
    type DataType = u16;
}

#[doc = "CTSU Sensor Counter"]
pub type Ctsusc = crate::RegValueT<Ctsusc_SPEC>;

impl Ctsusc {
    #[doc = "CTSU Sensor CounterThese bits indicate the measurement result of the CTSU. These bits indicate FFFFh when an overflow occurs."]
    #[inline(always)]
    pub fn ctsusc(
        self,
    ) -> crate::common::RegisterField<0, 0xffff, 1, 0, u16, u16, Ctsusc_SPEC, crate::common::R>
    {
        crate::common::RegisterField::<0,0xffff,1,0,u16,u16,Ctsusc_SPEC,crate::common::R>::from_register(self,0)
    }
}
impl ::core::default::Default for Ctsusc {
    #[inline(always)]
    fn default() -> Ctsusc {
        <crate::RegValueT<Ctsusc_SPEC> as RegisterValue<_>>::new(0)
    }
}

#[doc(hidden)]
#[derive(Copy, Clone, Eq, PartialEq)]
pub struct Ctsurc_SPEC;
impl crate::sealed::RegSpec for Ctsurc_SPEC {
    type DataType = u16;
}

#[doc = "CTSU Reference Counter"]
pub type Ctsurc = crate::RegValueT<Ctsurc_SPEC>;

impl Ctsurc {
    #[doc = "CTSU Reference CounterThese bits indicate the measurement result of the reference ICO.These bits indicate FFFFh when an overflow occurs."]
    #[inline(always)]
    pub fn ctsurc(
        self,
    ) -> crate::common::RegisterField<0, 0xffff, 1, 0, u16, u16, Ctsurc_SPEC, crate::common::R>
    {
        crate::common::RegisterField::<0,0xffff,1,0,u16,u16,Ctsurc_SPEC,crate::common::R>::from_register(self,0)
    }
}
impl ::core::default::Default for Ctsurc {
    #[inline(always)]
    fn default() -> Ctsurc {
        <crate::RegValueT<Ctsurc_SPEC> as RegisterValue<_>>::new(0)
    }
}

#[doc(hidden)]
#[derive(Copy, Clone, Eq, PartialEq)]
pub struct Ctsuerrs_SPEC;
impl crate::sealed::RegSpec for Ctsuerrs_SPEC {
    type DataType = u16;
}

#[doc = "CTSU Error Status Register"]
pub type Ctsuerrs = crate::RegValueT<Ctsuerrs_SPEC>;

impl Ctsuerrs {
    #[doc = "TSCAP Voltage Error Monitor"]
    #[inline(always)]
    pub fn ctsuicomp(
        self,
    ) -> crate::common::RegisterField<
        15,
        0x1,
        1,
        0,
        ctsuerrs::Ctsuicomp,
        ctsuerrs::Ctsuicomp,
        Ctsuerrs_SPEC,
        crate::common::R,
    > {
        crate::common::RegisterField::<
            15,
            0x1,
            1,
            0,
            ctsuerrs::Ctsuicomp,
            ctsuerrs::Ctsuicomp,
            Ctsuerrs_SPEC,
            crate::common::R,
        >::from_register(self, 0)
    }

    #[doc = "These bits are read as 000000000000000."]
    #[inline(always)]
    pub fn reserved(
        self,
    ) -> crate::common::RegisterField<0, 0x7fff, 1, 0, u16, u16, Ctsuerrs_SPEC, crate::common::R>
    {
        crate::common::RegisterField::<0,0x7fff,1,0,u16,u16,Ctsuerrs_SPEC,crate::common::R>::from_register(self,0)
    }
}
impl ::core::default::Default for Ctsuerrs {
    #[inline(always)]
    fn default() -> Ctsuerrs {
        <crate::RegValueT<Ctsuerrs_SPEC> as RegisterValue<_>>::new(0)
    }
}
pub mod ctsuerrs {

    #[derive(Clone, Copy, Eq, PartialEq, Ord, PartialOrd)]
    pub struct Ctsuicomp_SPEC;
    pub type Ctsuicomp = crate::EnumBitfieldStruct<u8, Ctsuicomp_SPEC>;
    impl Ctsuicomp {
        #[doc = "Normal TSCAP voltage"]
        pub const _0: Self = Self::new(0);

        #[doc = "Abnormal TSCAP voltage"]
        pub const _1: Self = Self::new(1);
    }
}