[−][src]Struct nrf52832_hal::nrf52832_pac::saadc::RegisterBlock
Register block
Fields
tasks_start: TASKS_START
0x00 - Start the ADC and prepare the result buffer in RAM
tasks_sample: TASKS_SAMPLE
0x04 - Take one ADC sample, if scan is enabled all channels are sampled
tasks_stop: TASKS_STOP
0x08 - Stop the ADC and terminate any on-going conversion
tasks_calibrateoffset: TASKS_CALIBRATEOFFSET
0x0c - Starts offset auto-calibration
events_started: EVENTS_STARTED
0x100 - The ADC has started
events_end: EVENTS_END
0x104 - The ADC has filled up the Result buffer
events_done: EVENTS_DONE
0x108 - A conversion task has been completed. Depending on the mode, multiple conversions might be needed for a result to be transferred to RAM.
events_resultdone: EVENTS_RESULTDONE
0x10c - A result is ready to get transferred to RAM.
events_calibratedone: EVENTS_CALIBRATEDONE
0x110 - Calibration is complete
events_stopped: EVENTS_STOPPED
0x114 - The ADC has stopped
events_ch: [EVENTS_CH; 8]
0x118 - Unspecified
inten: INTEN
0x300 - Enable or disable interrupt
intenset: INTENSET
0x304 - Enable interrupt
intenclr: INTENCLR
0x308 - Disable interrupt
status: STATUS
0x400 - Status
enable: ENABLE
0x500 - Enable or disable ADC
ch: [CH; 8]
0x510 - Unspecified
resolution: RESOLUTION
0x5f0 - Resolution configuration
oversample: OVERSAMPLE
0x5f4 - Oversampling configuration. OVERSAMPLE should not be combined with SCAN. The RESOLUTION is applied before averaging, thus for high OVERSAMPLE a higher RESOLUTION should be used.
samplerate: SAMPLERATE
0x5f8 - Controls normal or continuous sample rate
result: RESULT
0x62c - RESULT EasyDMA channel
Auto Trait Implementations
impl Send for RegisterBlock
impl Send for RegisterBlock
impl !Sync for RegisterBlock
impl !Sync for RegisterBlock
Blanket Implementations
impl<T, U> TryFrom for T where
T: From<U>,
[src]
impl<T, U> TryFrom for T where
T: From<U>,
type Error = !
try_from
)The type returned in the event of a conversion error.
fn try_from(value: U) -> Result<T, <T as TryFrom<U>>::Error>
[src]
fn try_from(value: U) -> Result<T, <T as TryFrom<U>>::Error>
try_from
)Performs the conversion.
impl<T> From for T
[src]
impl<T> From for T
impl<T, U> TryInto for T where
U: TryFrom<T>,
[src]
impl<T, U> TryInto for T where
U: TryFrom<T>,
type Error = <U as TryFrom<T>>::Error
try_from
)The type returned in the event of a conversion error.
fn try_into(self) -> Result<U, <U as TryFrom<T>>::Error>
[src]
fn try_into(self) -> Result<U, <U as TryFrom<T>>::Error>
try_from
)Performs the conversion.
impl<T, U> Into for T where
U: From<T>,
[src]
impl<T, U> Into for T where
U: From<T>,
impl<T> Borrow for T where
T: ?Sized,
[src]
impl<T> Borrow for T where
T: ?Sized,
impl<T> BorrowMut for T where
T: ?Sized,
[src]
impl<T> BorrowMut for T where
T: ?Sized,
fn borrow_mut(&mut self) -> &mut T
[src]
fn borrow_mut(&mut self) -> &mut T
Mutably borrows from an owned value. Read more
impl<T> Any for T where
T: 'static + ?Sized,
[src]
impl<T> Any for T where
T: 'static + ?Sized,
fn get_type_id(&self) -> TypeId
[src]
fn get_type_id(&self) -> TypeId
🔬 This is a nightly-only experimental API. (get_type_id
)
this method will likely be replaced by an associated static
Gets the TypeId
of self
. Read more