[−][src]Struct nrf52832_hal::nrf52832_pac::saadc::RegisterBlock

#[repr(C)]

pub struct RegisterBlock {
    pub tasks_start: TASKS_START,
    pub tasks_sample: TASKS_SAMPLE,
    pub tasks_stop: TASKS_STOP,
    pub tasks_calibrateoffset: TASKS_CALIBRATEOFFSET,
    pub events_started: EVENTS_STARTED,
    pub events_end: EVENTS_END,
    pub events_done: EVENTS_DONE,
    pub events_resultdone: EVENTS_RESULTDONE,
    pub events_calibratedone: EVENTS_CALIBRATEDONE,
    pub events_stopped: EVENTS_STOPPED,
    pub events_ch: [EVENTS_CH; 8],
    pub inten: INTEN,
    pub intenset: INTENSET,
    pub intenclr: INTENCLR,
    pub status: STATUS,
    pub enable: ENABLE,
    pub ch: [CH; 8],
    pub resolution: RESOLUTION,
    pub oversample: OVERSAMPLE,
    pub samplerate: SAMPLERATE,
    pub result: RESULT,
    // some fields omitted
}

Register block

Fields

0x00 - Start the ADC and prepare the result buffer in RAM

0x04 - Take one ADC sample, if scan is enabled all channels are sampled

0x08 - Stop the ADC and terminate any on-going conversion

0x0c - Starts offset auto-calibration

0x100 - The ADC has started

0x104 - The ADC has filled up the Result buffer

0x108 - A conversion task has been completed. Depending on the mode, multiple conversions might be needed for a result to be transferred to RAM.

0x10c - A result is ready to get transferred to RAM.

0x110 - Calibration is complete

0x114 - The ADC has stopped

0x118 - Unspecified

0x300 - Enable or disable interrupt

0x304 - Enable interrupt

0x308 - Disable interrupt

0x400 - Status

0x500 - Enable or disable ADC

0x510 - Unspecified

0x5f0 - Resolution configuration

0x5f4 - Oversampling configuration. OVERSAMPLE should not be combined with SCAN. The RESOLUTION is applied before averaging, thus for high OVERSAMPLE a higher RESOLUTION should be used.

0x5f8 - Controls normal or continuous sample rate

0x62c - RESULT EasyDMA channel

Auto Trait Implementations

Blanket Implementations

impl<T> From for T
[src]

Performs the conversion.

impl<T, U> TryFrom for T where
    T: From<U>, 
[src]

🔬 This is a nightly-only experimental API. (try_from)

The type returned in the event of a conversion error.

🔬 This is a nightly-only experimental API. (try_from)

Performs the conversion.

impl<T, U> TryInto for T where
    U: TryFrom<T>, 
[src]

🔬 This is a nightly-only experimental API. (try_from)

The type returned in the event of a conversion error.

🔬 This is a nightly-only experimental API. (try_from)

Performs the conversion.

impl<T, U> Into for T where
    U: From<T>, 
[src]

Performs the conversion.

impl<T> Borrow for T where
    T: ?Sized, 
[src]

Immutably borrows from an owned value. Read more

impl<T> BorrowMut for T where
    T: ?Sized, 
[src]

Mutably borrows from an owned value. Read more

impl<T> Any for T where
    T: 'static + ?Sized, 
[src]

🔬 This is a nightly-only experimental API. (get_type_id)

this method will likely be replaced by an associated static

Gets the TypeId of self. Read more