[−][src]Struct cc13x2_cc26x2_hal::aux_anaif::RegisterBlock
Register block
Fields
adcctl: ADCCTL
0x10 - ADC Control Configuration of ADI_4_AUX:ADC0.SMPL_MODE decides if the ADC trigger starts sampling or conversion.
adcfifostat: ADCFIFOSTAT
0x14 - ADC FIFO Status FIFO can hold up to four ADC samples.
adcfifo: ADCFIFO
0x18 - ADC FIFO
adctrig: ADCTRIG
0x1c - ADC Trigger
isrcctl: ISRCCTL
0x20 - Current Source Control
dacctl: DACCTL
0x30 - DAC Control This register controls the analog part of the DAC.
lpmbiasctl: LPMBIASCTL
0x34 - Low Power Mode Bias Control The low power mode bias module provides bias current to DAC and Comparator A when AUX_SYSIF:OPMODEREQ.REQ differers from A.
dacsmplctl: DACSMPLCTL
0x38 - DAC Sample Control The DAC sample clock maintains the DAC voltage stored in the sample-and-hold capacitor. The DAC sample clock waveform consists of a setup phase followed by a hold phase. In the setup phase the sample-and-hold capacitor charges to the programmed voltage. The hold phase maintains the voltage with minimal power. DACSMPLCFG0 and DACSMPLCFG1 configure the DAC sample clock waveform.
dacsmplcfg0: DACSMPLCFG0
0x3c - DAC Sample Configuration 0
dacsmplcfg1: DACSMPLCFG1
0x40 - DAC Sample Configuration 1 The sample clock period equals (high time + low time) * base period. DACSMPLCFG0.CLKDIV determines the base period. Timing requirements (DAC Buffer On / DAC Buffer Off): - (high time + low time) * base period > (4 us / 1 us) - (high time * base period) > (2 us / 0.5 us) - (low time * base period) > (2 us / 0.5 us) - (low time * base period + HOLD_INTERVAL * sample clock period) < 32 us If AUX_SYSIF:OPMODEREQ.REQ equals PDLP, you must set: - H_PER = L_PER = HOLD_INTERVAL = 0.
dacvalue: DACVALUE
0x44 - DAC Value
dacstat: DACSTAT
0x48 - DAC Status
Auto Trait Implementations
impl Send for RegisterBlock
impl !Sync for RegisterBlock
Blanket Implementations
impl<T> From for T
[src]
impl<T, U> TryFrom for T where
U: Into<T>,
[src]
U: Into<T>,
type Error = Infallible
The type returned in the event of a conversion error.
fn try_from(value: U) -> Result<T, <T as TryFrom<U>>::Error>
[src]
impl<T, U> TryInto for T where
U: TryFrom<T>,
[src]
U: TryFrom<T>,
type Error = <U as TryFrom<T>>::Error
The type returned in the event of a conversion error.
fn try_into(self) -> Result<U, <U as TryFrom<T>>::Error>
[src]
impl<T, U> Into for T where
U: From<T>,
[src]
U: From<T>,
impl<T> Borrow for T where
T: ?Sized,
[src]
T: ?Sized,
impl<T> BorrowMut for T where
T: ?Sized,
[src]
T: ?Sized,
fn borrow_mut(&mut self) -> &mut T
[src]
impl<T> Any for T where
T: 'static + ?Sized,
[src]
T: 'static + ?Sized,
impl<T> Same for T
type Output = T
Should always be Self