Struct stm32h7::stm32h743::sdmmc1::dctrl::W

pub struct W(_);

Register DCTRL writer

Implementations

impl W

pub fn dten(&mut self) -> DTEN_W<'_, 0>

Bit 0 - Data transfer enable bit This bit can only be written by firmware when DPSM is inactive (DPSMACT = 0). This bit is cleared by Hardware when data transfer completes. This bit shall only be used to transfer data when no associated data transfer command is used, i.e. shall not be used with SD or eMMC cards.

pub fn dtdir(&mut self) -> DTDIR_W<'_, 1>

Bit 1 - Data transfer direction selection This bit can only be written by firmware when DPSM is inactive (DPSMACT = 0).

pub fn dtmode(&mut self) -> DTMODE_W<'_, 2>

Bits 2:3 - Data transfer mode selection. This bit can only be written by firmware when DPSM is inactive (DPSMACT = 0).

pub fn dblocksize(&mut self) -> DBLOCKSIZE_W<'_, 4>

Bits 4:7 - Data block size This bit can only be written by firmware when DPSM is inactive (DPSMACT = 0). Define the data block length when the block data transfer mode is selected: When DATALENGTH is not a multiple of DBLOCKSIZE, the transfered data is truncated at a multiple of DBLOCKSIZE. (Any remain data will not be transfered.) When DDR = 1, DBLOCKSIZE = 0000 shall not be used. (No data will be transfered)

pub fn rwstart(&mut self) -> RWSTART_W<'_, 8>

Bit 8 - Read wait start. If this bit is set, read wait operation starts.

pub fn rwstop(&mut self) -> RWSTOP_W<'_, 9>

Bit 9 - Read wait stop This bit is written by firmware and auto cleared by hardware when the DPSM moves from the READ_WAIT state to the WAIT_R or IDLE state.

pub fn rwmod(&mut self) -> RWMOD_W<'_, 10>

Bit 10 - Read wait mode. This bit can only be written by firmware when DPSM is inactive (DPSMACT = 0).

pub fn sdioen(&mut self) -> SDIOEN_W<'_, 11>

Bit 11 - SD I/O interrupt enable functions This bit can only be written by firmware when DPSM is inactive (DPSMACT = 0). If this bit is set, the DPSM enables the SD I/O card specific interrupt operation.

pub fn bootacken(&mut self) -> BOOTACKEN_W<'_, 12>

Bit 12 - Enable the reception of the boot acknowledgment. This bit can only be written by firmware when DPSM is inactive (DPSMACT = 0).

pub fn fiforst(&mut self) -> FIFORST_W<'_, 13>

Bit 13 - FIFO reset, will flush any remaining data. This bit can only be written by firmware when IDMAEN= 0 and DPSM is active (DPSMACT = 1). This bit will only take effect when a transfer error or transfer hold occurs.

pub unsafe fn bits(&mut self, bits: u32) -> &mut Self

Writes raw bits to the register.

Methods from Deref<Target = W<DCTRL_SPEC>>

pub unsafe fn bits(&mut self, bits: REG::Ux) -> &mut Self

Writes raw bits to the register.

Trait Implementations

impl Deref for W

type Target = W<DCTRL_SPEC>

The resulting type after dereferencing.

fn deref(&self) -> &Self::Target

Dereferences the value.

impl DerefMut for W

fn deref_mut(&mut self) -> &mut Self::Target

Mutably dereferences the value.

impl From<W<DCTRL_SPEC>> for W

fn from(writer: W<DCTRL_SPEC>) -> Self

Converts to this type from the input type.