Struct stm32h7::stm32h743::quadspi::cr::W

source · [−]

pub struct W(_);

Expand description

Register CR writer

Implementations

source

impl W

source

pub fn en(&mut self) -> EN_W<'_, 0>

Bit 0 - Enable Enable the QUADSPI.

source

pub fn abort(&mut self) -> ABORT_W<'_, 1>

Bit 1 - Abort request This bit aborts the on-going command sequence. It is automatically reset once the abort is complete. This bit stops the current transfer. In polling mode or memory-mapped mode, this bit also reset the APM bit or the DM bit.

source

pub fn dmaen(&mut self) -> DMAEN_W<'_, 2>

Bit 2 - DMA enable In indirect mode, DMA can be used to input or output data via the QUADSPI_DR register. DMA transfers are initiated when the FIFO threshold flag, FTF, is set.

source

pub fn tcen(&mut self) -> TCEN_W<'_, 3>

Bit 3 - Timeout counter enable This bit is valid only when memory-mapped mode (FMODE = 11) is selected. Activating this bit causes the chip select (nCS) to be released (and thus reduces consumption) if there has not been an access after a certain amount of time, where this time is defined by TIMEOUT[15:0] (QUADSPI_LPTR). Enable the timeout counter. By default, the QUADSPI never stops its prefetch operation, keeping the previous read operation active with nCS maintained low, even if no access to the Flash memory occurs for a long time. Since Flash memories tend to consume more when nCS is held low, the application might want to activate the timeout counter (TCEN = 1, QUADSPI_CR[3]) so that nCS is released after a period of TIMEOUT[15:0] (QUADSPI_LPTR) cycles have elapsed without an access since when the FIFO becomes full with prefetch data. This bit can be modified only when BUSY = 0.

source

pub fn sshift(&mut self) -> SSHIFT_W<'_, 4>

Bit 4 - Sample shift By default, the QUADSPI samples data 1/2 of a CLK cycle after the data is driven by the Flash memory. This bit allows the data is to be sampled later in order to account for external signal delays. Firmware must assure that SSHIFT = 0 when in DDR mode (when DDRM = 1). This field can be modified only when BUSY = 0.

source

pub fn dfm(&mut self) -> DFM_W<'_, 6>

Bit 6 - Dual-flash mode This bit activates dual-flash mode, where two external Flash memories are used simultaneously to double throughput and capacity. This bit can be modified only when BUSY = 0.

source

pub fn fsel(&mut self) -> FSEL_W<'_, 7>

Bit 7 - Flash memory selection This bit selects the Flash memory to be addressed in single flash mode (when DFM = 0). This bit can be modified only when BUSY = 0. This bit is ignored when DFM = 1.

source

pub fn fthres(&mut self) -> FTHRES_W<'_, 8>

Bits 8:12 - FIFO threshold level Defines, in indirect mode, the threshold number of bytes in the FIFO that will cause the FIFO threshold flag (FTF, QUADSPI_SR[2]) to be set. In indirect write mode (FMODE = 00): … In indirect read mode (FMODE = 01): … If DMAEN = 1, then the DMA controller for the corresponding channel must be disabled before changing the FTHRES value.

source

pub fn teie(&mut self) -> TEIE_W<'_, 16>

Bit 16 - Transfer error interrupt enable This bit enables the transfer error interrupt.

source

pub fn tcie(&mut self) -> TCIE_W<'_, 17>

Bit 17 - Transfer complete interrupt enable This bit enables the transfer complete interrupt.

source

pub fn ftie(&mut self) -> FTIE_W<'_, 18>

Bit 18 - FIFO threshold interrupt enable This bit enables the FIFO threshold interrupt.

source

pub fn smie(&mut self) -> SMIE_W<'_, 19>

Bit 19 - Status match interrupt enable This bit enables the status match interrupt.

source

pub fn toie(&mut self) -> TOIE_W<'_, 20>

Bit 20 - TimeOut interrupt enable This bit enables the TimeOut interrupt.

source

pub fn apms(&mut self) -> APMS_W<'_, 22>

Bit 22 - Automatic poll mode stop This bit determines if automatic polling is stopped after a match. This bit can be modified only when BUSY = 0.

source

pub fn pmm(&mut self) -> PMM_W<'_, 23>

Bit 23 - Polling match mode This bit indicates which method should be used for determining a match during automatic polling mode. This bit can be modified only when BUSY = 0.

source