[−][src]Struct stm32f3::stm32f3x8::usart1::cr2::W
Value to write to the register
Methods
impl W
[src]
impl W
pub fn reset_value() -> W | [src] |
Reset value of the register
pub unsafe fn bits(&mut self, bits: u32) -> &mut Self | [src] |
Writes raw bits to the register
pub fn rtoen(&mut self) -> _RTOENW | [src] |
Bit 23 - Receiver timeout enable
pub fn abrmod(&mut self) -> _ABRMODW | [src] |
Bits 21:22 - Auto baud rate mode
pub fn abren(&mut self) -> _ABRENW | [src] |
Bit 20 - Auto baud rate enable
pub fn msbfirst(&mut self) -> _MSBFIRSTW | [src] |
Bit 19 - Most significant bit first
pub fn datainv(&mut self) -> _DATAINVW | [src] |
Bit 18 - Binary data inversion
pub fn txinv(&mut self) -> _TXINVW | [src] |
Bit 17 - TX pin active level inversion
pub fn rxinv(&mut self) -> _RXINVW | [src] |
Bit 16 - RX pin active level inversion
pub fn swap(&mut self) -> _SWAPW | [src] |
Bit 15 - Swap TX/RX pins
pub fn linen(&mut self) -> _LINENW | [src] |
Bit 14 - LIN mode enable
pub fn stop(&mut self) -> _STOPW | [src] |
Bits 12:13 - STOP bits
pub fn clken(&mut self) -> _CLKENW | [src] |
Bit 11 - Clock enable
pub fn cpol(&mut self) -> _CPOLW | [src] |
Bit 10 - Clock polarity
pub fn cpha(&mut self) -> _CPHAW | [src] |
Bit 9 - Clock phase
pub fn lbcl(&mut self) -> _LBCLW | [src] |
Bit 8 - Last bit clock pulse
pub fn lbdie(&mut self) -> _LBDIEW | [src] |
Bit 6 - LIN break detection interrupt enable
pub fn lbdl(&mut self) -> _LBDLW | [src] |
Bit 5 - LIN break detection length
pub fn addm7(&mut self) -> _ADDM7W | [src] |
Bit 4 - 7-bit Address Detection/4-bit Address Detection
pub fn add(&mut self) -> _ADDW | [src] |
Bits 24:31 - Address of the USART node
Auto Trait Implementations
Blanket Implementations
impl<T, U> TryFrom for T where
T: From<U>,
[src]
impl<T, U> TryFrom for T where
T: From<U>,
type Error = !
try_from
)The type returned in the event of a conversion error.
fn try_from(value: U) -> Result<T, <T as TryFrom<U>>::Error> | [src] |
impl<T> From for T
[src]
impl<T> From for T
impl<T, U> TryInto for T where
U: TryFrom<T>,
[src]
impl<T, U> TryInto for T where
U: TryFrom<T>,
type Error = <U as TryFrom<T>>::Error
try_from
)The type returned in the event of a conversion error.
fn try_into(self) -> Result<U, <U as TryFrom<T>>::Error> | [src] |
impl<T, U> Into for T where
U: From<T>,
[src]
impl<T, U> Into for T where
U: From<T>,
impl<T> Borrow for T where
T: ?Sized,
[src]
impl<T> Borrow for T where
T: ?Sized,
impl<T> BorrowMut for T where
T: ?Sized,
[src]
impl<T> BorrowMut for T where
T: ?Sized,
fn borrow_mut(&mut self) -> &mut T | [src] |
impl<T> Any for T where
T: 'static + ?Sized,
[src]
impl<T> Any for T where
T: 'static + ?Sized,
fn get_type_id(&self) -> TypeId | [src] |