[−][src]Struct stm32f1xx_hal::gpio::gpiod::PD2
Pin
Methods
impl<MODE> PD2<MODE>
[src]
pub fn into_alternate_push_pull(self, cr: &mut CRL) -> PD2<Alternate<PushPull>>
[src]
Configures the pin to operate as an alternate function push-pull output pin.
pub fn into_alternate_open_drain(
self,
cr: &mut CRL
) -> PD2<Alternate<OpenDrain>>
[src]
self,
cr: &mut CRL
) -> PD2<Alternate<OpenDrain>>
Configures the pin to operate as an alternate function open-drain output pin.
pub fn into_floating_input(self, cr: &mut CRL) -> PD2<Input<Floating>>
[src]
Configures the pin to operate as a floating input pin
pub fn into_pull_down_input(self, cr: &mut CRL) -> PD2<Input<PullDown>>
[src]
Configures the pin to operate as a pulled down input pin
pub fn into_pull_up_input(self, cr: &mut CRL) -> PD2<Input<PullUp>>
[src]
Configures the pin to operate as a pulled up input pin
pub fn into_open_drain_output(self, cr: &mut CRL) -> PD2<Output<OpenDrain>>
[src]
Configures the pin to operate as an open-drain output pin. Initial state will be low.
pub fn into_open_drain_output_with_state(
self,
cr: &mut CRL,
initial_state: State
) -> PD2<Output<OpenDrain>>
[src]
self,
cr: &mut CRL,
initial_state: State
) -> PD2<Output<OpenDrain>>
Configures the pin to operate as an open-drain output pin.
initial_state
specifies whether the pin should be initially high or low.
pub fn into_push_pull_output(self, cr: &mut CRL) -> PD2<Output<PushPull>>
[src]
Configures the pin to operate as an push-pull output pin. Initial state will be low.
pub fn into_push_pull_output_with_state(
self,
cr: &mut CRL,
initial_state: State
) -> PD2<Output<PushPull>>
[src]
self,
cr: &mut CRL,
initial_state: State
) -> PD2<Output<PushPull>>
Configures the pin to operate as an push-pull output pin.
initial_state
specifies whether the pin should be initially high or low.
pub fn into_analog(self, cr: &mut CRL) -> PD2<Analog>
[src]
Configures the pin to operate as an analog input pin
impl<MODE> PD2<MODE>
[src]
pub fn downgrade(self) -> PDx<MODE>
[src]
Erases the pin number from the type
This is useful when you want to collect the pins into an array where you need all the elements to have the same type
Trait Implementations
impl<MODE> OutputPin for PD2<Output<MODE>>
[src]
impl<MODE> OutputPin for PD2<Alternate<MODE>>
[src]
impl<MODE> StatefulOutputPin for PD2<Output<MODE>>
[src]
fn is_set_high(&self) -> bool
[src]
fn is_set_low(&self) -> bool
[src]
impl<MODE> StatefulOutputPin for PD2<Alternate<MODE>>
[src]
fn is_set_high(&self) -> bool
[src]
fn is_set_low(&self) -> bool
[src]
impl<MODE> Default for PD2<Output<MODE>>
[src]
impl<MODE> InputPin for PD2<Input<MODE>>
[src]
impl InputPin for PD2<Output<OpenDrain>>
[src]
Auto Trait Implementations
Blanket Implementations
impl<T, U> TryFrom for T where
U: Into<T>,
[src]
U: Into<T>,
type Error = Infallible
The type returned in the event of a conversion error.
fn try_from(value: U) -> Result<T, <T as TryFrom<U>>::Error>
[src]
impl<T> From for T
[src]
impl<T, U> TryInto for T where
U: TryFrom<T>,
[src]
U: TryFrom<T>,
type Error = <U as TryFrom<T>>::Error
The type returned in the event of a conversion error.
fn try_into(self) -> Result<U, <U as TryFrom<T>>::Error>
[src]
impl<T, U> Into for T where
U: From<T>,
[src]
U: From<T>,
impl<T> Borrow for T where
T: ?Sized,
[src]
T: ?Sized,
impl<T> BorrowMut for T where
T: ?Sized,
[src]
T: ?Sized,
fn borrow_mut(&mut self) -> &mut T
[src]
impl<T> Any for T where
T: 'static + ?Sized,
[src]
T: 'static + ?Sized,
impl<P> ToggleableOutputPin for P where
P: Default,
[src]
P: Default,
impl<T> Same for T
type Output = T
Should always be Self