Struct Shape

pub struct Shape { /* private fields */ }

Implementations

impl Shape

pub fn visible(self, value: bool) -> Self

Determines whether or not this shape is visible.

pub fn layer(self, value: ShapeLayer) -> Self

Specifies whether shapes are drawn below or above traces.

pub fn x_ref(self, value: impl AsRef<str>) -> Self

Sets the shape’s x coordinate axis. If set to an x axis id (e.g. “x” or “x2”), the x position refers to an x coordinate. If set to “paper”, the x position refers to the distance from the left side of the plotting area in normalized coordinates where “0” (“1”) corresponds to the left (right) side. If the axis type is “log”, then you must take the log of your desired range. If the axis type is “date”, then you must convert the date to unix time in milliseconds.

pub fn x_size_mode(self, value: ShapeSizeMode) -> Self

Sets the shapes’s sizing mode along the x axis. If set to “scaled”, x0, x1 and x coordinates within path refer to data values on the x axis or a fraction of the plot area’s width (xref set to “paper”). If set to “pixel”, xanchor specifies the x position in terms of data or plot fraction but x0, x1 and x coordinates within path are pixels relative to xanchor. This way, the shape can have a fixed width while maintaining a position relative to data or plot fraction.

pub fn x_anchor(self, value: impl Into<NumOrString>) -> Self

Only relevant in conjunction with xsizemode set to “pixel”. Specifies the anchor point on the x axis to which x0, x1 and x coordinates within path are relative to. E.g. useful to attach a pixel sized shape to a certain data value. No effect when xsizemode not set to “pixel”.

pub fn x0(self, value: impl Into<NumOrString>) -> Self

Sets the shape’s starting x position. See type and xsizemode for more info.

pub fn x1(self, value: impl Into<NumOrString>) -> Self

Sets the shape’s end x position. See type and xsizemode for more info.

pub fn y_ref(self, value: impl AsRef<str>) -> Self

Sets the annotation’s y coordinate axis. If set to an y axis id (e.g. “y” or “y2”), the y position refers to an y coordinate If set to “paper”, the y position refers to the distance from the bottom of the plotting area in normalized coordinates where “0” (“1”) corresponds to the bottom (top).

pub fn y_size_mode(self, value: ShapeSizeMode) -> Self

Sets the shapes’s sizing mode along the y axis. If set to “scaled”, y0, y1 and y coordinates within path refer to data values on the y axis or a fraction of the plot area’s height (yref set to “paper”). If set to “pixel”, yanchor specifies the y position in terms of data or plot fraction but y0, y1 and y coordinates within path are pixels relative to yanchor. This way, the shape can have a fixed height while maintaining a position relative to data or plot fraction.

pub fn y_anchor(self, value: impl Into<NumOrString>) -> Self

Only relevant in conjunction with ysizemode set to “pixel”. Specifies the anchor point on the y axis to which y0, y1 and y coordinates within path are relative to. E.g. useful to attach a pixel sized shape to a certain data value. No effect when ysizemode not set to “pixel”.

pub fn y0(self, value: impl Into<NumOrString>) -> Self

Sets the shape’s starting y position. See type and ysizemode for more info.

pub fn y1(self, value: impl Into<NumOrString>) -> Self

Sets the shape’s end y position. See type and ysizemode for more info.

pub fn path(self, value: impl AsRef<str>) -> Self

For type “path” - a valid SVG path with the pixel values replaced by data values in xsizemode/ysizemode being “scaled” and taken unmodified as pixels relative to xanchor and yanchor in case of “pixel” size mode. There are a few restrictions / quirks only absolute instructions, not relative. So the allowed segments are: M, L, H, V, Q, C, T, S, and Z arcs (A) are not allowed because radius rx and ry are relative. In the future we could consider supporting relative commands, but we would have to decide on how to handle date and log axes. Note that even as is, Q and C Bezier paths that are smooth on linear axes may not be smooth on log, and vice versa. no chained “polybezier” commands - specify the segment type for each one. On category axes, values are numbers scaled to the serial numbers of categories because using the categories themselves there would be no way to describe fractional positions On data axes: because space and T are both normal components of path strings, we can’t use either to separate date from time parts. Therefore we’ll use underscore for this purpose: 2015-02-21_13:45:56.789

pub fn opacity(self, value: f64) -> Self

Sets the opacity of the shape. Number between or equal to 0 and 1.

pub fn line(self, value: ShapeLine) -> Self

Sets the shape line properties (color, width, dash).

pub fn fill_color(self, value: impl Color) -> Self

Sets the color filling the shape’s interior. Only applies to closed shapes.

pub fn fill_rule(self, value: FillRule) -> Self

Determines which regions of complex paths constitute the interior. For more info please visit https://developer.mozilla.org/en-US/docs/Web/SVG/Attribute/fill-rule

pub fn editable(self, value: bool) -> Self

Determines whether the shape could be activated for edit or not. Has no effect when the older editable shapes mode is enabled via config.editable or config.edits.shapePosition.

pub fn name(self, value: impl AsRef<str>) -> Self

When used in a template, named items are created in the output figure in addition to any items the figure already has in this array. You can modify these items in the output figure by making your own item with templateitemname matching this name alongside your modifications (including visible: false or enabled: false to hide it). Has no effect outside of a template.

pub fn template_item_name(self, value: impl AsRef<str>) -> Self

Used to refer to a named item in this array in the template. Named items from the template will be created even without a matching item in the input figure, but you can modify one by making an item with templateitemname matching its name, alongside your modifications (including visible: false or enabled: false to hide it). If there is no template or no matching item, this item will be hidden unless you explicitly show it with visible: true.

impl Shape

pub fn new() -> Self

pub fn shape_type(self, shape_type: ShapeType) -> Self

Specifies the shape type to be drawn. If “line”, a line is drawn from (x0,y0) to (x1,y1) with respect to the axes’ sizing mode. If “circle”, a circle is drawn from ((x0+x1)/2, (y0+y1)/2)) with radius (|(x0+x1)/2 - x0|, |(y0+y1)/2 -y0)|) with respect to the axes’ sizing mode. If “rect”, a rectangle is drawn linking (x0,y0), (x1,y0), (x1,y1), (x0,y1), (x0,y0) with respect to the axes’ sizing mode. If “path”, draw a custom SVG path using path. with respect to the axes’ sizing mode.

Trait Implementations

impl Clone for Shape

fn clone(&self) -> Shape

Returns a duplicate of the value.

fn clone_from(&mut self, source: &Self)

Performs copy-assignment from source.

impl Debug for Shape

fn fmt(&self, f: &mut Formatter<'_>) -> Result

Formats the value using the given formatter.

impl Default for Shape

fn default() -> Self

Returns the “default value” for a type.

impl Serialize for Shape

fn serialize<__S>(&self, __serializer: __S) -> Result<__S::Ok, __S::Error>

where __S: Serializer,

Serialize this value into the given Serde serializer.