[−][src]Struct nrf9160_hal::gpio::p0::P0_17
Implementations
impl<MODE> P0_17<MODE>
[src]
pub fn into_floating_input(self) -> P0_17<Input<Floating>>
[src]
Convert the pin to be a floating input
pub fn into_pulldown_input(self) -> P0_17<Input<PullDown>>
[src]
pub fn into_pullup_input(self) -> P0_17<Input<PullUp>>
[src]
pub fn into_push_pull_output(
self,
initial_output: Level
) -> P0_17<Output<PushPull>>
[src]
self,
initial_output: Level
) -> P0_17<Output<PushPull>>
Convert the pin to bepin a push-pull output with normal drive
pub fn into_open_drain_output(
self,
config: OpenDrainConfig,
initial_output: Level
) -> P0_17<Output<OpenDrain>>
[src]
self,
config: OpenDrainConfig,
initial_output: Level
) -> P0_17<Output<OpenDrain>>
Convert the pin to be an open-drain output
This method currently does not support configuring an internal pull-up or pull-down resistor.
pub fn degrade(self) -> Pin<MODE>
[src]
Degrade to a generic pin struct, which can be used with peripherals
Trait Implementations
impl Channel<Saadc> for P0_17<Input<Floating>>
[src]
type ID = u8
Channel ID type Read more
fn channel() -> <P0_17<Input<Floating>> as Channel<Saadc>>::ID
[src]
impl<MODE> InputPin for P0_17<Input<MODE>>
[src]
type Error = Void
Error type
fn is_high(&self) -> Result<bool, <P0_17<Input<MODE>> as InputPin>::Error>
[src]
fn is_low(&self) -> Result<bool, <P0_17<Input<MODE>> as InputPin>::Error>
[src]
impl<MODE> OutputPin for P0_17<Output<MODE>>
[src]
type Error = Void
Error type
fn set_high(&mut self) -> Result<(), <P0_17<Output<MODE>> as OutputPin>::Error>
[src]
Set the output as high
fn set_low(&mut self) -> Result<(), <P0_17<Output<MODE>> as OutputPin>::Error>
[src]
Set the output as low
impl<MODE> StatefulOutputPin for P0_17<Output<MODE>>
[src]
Auto Trait Implementations
impl<MODE> Send for P0_17<MODE> where
MODE: Send,
MODE: Send,
impl<MODE> Sync for P0_17<MODE> where
MODE: Sync,
MODE: Sync,
impl<MODE> Unpin for P0_17<MODE> where
MODE: Unpin,
MODE: Unpin,
Blanket Implementations
impl<T> Any for T where
T: 'static + ?Sized,
[src]
T: 'static + ?Sized,
impl<T> Borrow<T> for T where
T: ?Sized,
[src]
T: ?Sized,
impl<T> BorrowMut<T> for T where
T: ?Sized,
[src]
T: ?Sized,
fn borrow_mut(&mut self) -> &mut T
[src]
impl<T> From<T> for T
[src]
impl<T> InputPin for T where
T: InputPin,
[src]
T: InputPin,
type Error = ()
Error type
fn is_low(&self) -> Result<bool, <T as InputPin>::Error>
[src]
fn is_high(&self) -> Result<bool, <T as InputPin>::Error>
[src]
impl<T, U> Into<U> for T where
U: From<T>,
[src]
U: From<T>,
impl<T> OutputPin for T where
T: OutputPin,
[src]
T: OutputPin,
type Error = ()
Error type
fn set_low(&mut self) -> Result<(), <T as OutputPin>::Error>
[src]
fn set_high(&mut self) -> Result<(), <T as OutputPin>::Error>
[src]
impl<T> Same<T> for T
type Output = T
Should always be Self
impl<T> StatefulOutputPin for T where
T: StatefulOutputPin + OutputPin,
[src]
T: StatefulOutputPin + OutputPin,
fn is_set_low(&self) -> Result<bool, <T as OutputPin>::Error>
[src]
fn is_set_high(&self) -> Result<bool, <T as OutputPin>::Error>
[src]
impl<T, U> TryFrom<U> for T where
U: Into<T>,
[src]
U: Into<T>,
type Error = Infallible
The type returned in the event of a conversion error.
fn try_from(value: U) -> Result<T, <T as TryFrom<U>>::Error>
[src]
impl<T, U> TryInto<U> for T where
U: TryFrom<T>,
[src]
U: TryFrom<T>,