Struct nrf52832_hal::gpio::p0::P0_10 [−][src]
pub struct P0_10<MODE> { /* fields omitted */ }
Implementations
impl<MODE> P0_10<MODE>
[src]
impl<MODE> P0_10<MODE>
[src]pub fn into_floating_input(self) -> P0_10<Input<Floating>>
[src]
pub fn into_floating_input(self) -> P0_10<Input<Floating>>
[src]Convert the pin to be a floating input
pub fn into_pulldown_input(self) -> P0_10<Input<PullDown>>
[src]
pub fn into_pullup_input(self) -> P0_10<Input<PullUp>>
[src]
pub fn into_push_pull_output(
self,
initial_output: Level
) -> P0_10<Output<PushPull>>
[src]
pub fn into_push_pull_output(
self,
initial_output: Level
) -> P0_10<Output<PushPull>>
[src]Convert the pin to bepin a push-pull output with normal drive
pub fn into_open_drain_output(
self,
config: OpenDrainConfig,
initial_output: Level
) -> P0_10<Output<OpenDrain>>
[src]
pub fn into_open_drain_output(
self,
config: OpenDrainConfig,
initial_output: Level
) -> P0_10<Output<OpenDrain>>
[src]Convert the pin to be an open-drain output
This method currently does not support configuring an internal pull-up or pull-down resistor.
pub fn into_disconnected(self) -> P0_10<Disconnected>
[src]
pub fn into_disconnected(self) -> P0_10<Disconnected>
[src]Disconnects the pin.
In disconnected mode the pin cannot be used as input or output. It is primarily useful to reduce power usage.
Trait Implementations
Auto Trait Implementations
impl<MODE> Send for P0_10<MODE> where
MODE: Send,
MODE: Send,
impl<MODE> Sync for P0_10<MODE> where
MODE: Sync,
MODE: Sync,
impl<MODE> Unpin for P0_10<MODE> where
MODE: Unpin,
MODE: Unpin,
Blanket Implementations
impl<T> BorrowMut<T> for T where
T: ?Sized,
[src]
impl<T> BorrowMut<T> for T where
T: ?Sized,
[src]pub fn borrow_mut(&mut self) -> &mut T
[src]
pub fn borrow_mut(&mut self) -> &mut T
[src]Mutably borrows from an owned value. Read more
impl<T> CheckedAs for T
[src]
impl<T> CheckedAs for T
[src]pub fn checked_as<Dst>(self) -> Option<Dst> where
T: CheckedCast<Dst>,
[src]
pub fn checked_as<Dst>(self) -> Option<Dst> where
T: CheckedCast<Dst>,
[src]Casts the value.
impl<Src, Dst> LosslessTryInto<Dst> for Src where
Dst: LosslessTryFrom<Src>,
[src]
impl<Src, Dst> LosslessTryInto<Dst> for Src where
Dst: LosslessTryFrom<Src>,
[src]pub fn lossless_try_into(self) -> Option<Dst>
[src]
pub fn lossless_try_into(self) -> Option<Dst>
[src]Performs the conversion.
impl<Src, Dst> LossyInto<Dst> for Src where
Dst: LossyFrom<Src>,
[src]
impl<Src, Dst> LossyInto<Dst> for Src where
Dst: LossyFrom<Src>,
[src]pub fn lossy_into(self) -> Dst
[src]
pub fn lossy_into(self) -> Dst
[src]Performs the conversion.
impl<T> OverflowingAs for T
[src]
impl<T> OverflowingAs for T
[src]pub fn overflowing_as<Dst>(self) -> (Dst, bool) where
T: OverflowingCast<Dst>,
[src]
pub fn overflowing_as<Dst>(self) -> (Dst, bool) where
T: OverflowingCast<Dst>,
[src]Casts the value.
impl<T> Same<T> for T
impl<T> Same<T> for T
type Output = T
type Output = T
Should always be Self
impl<T> SaturatingAs for T
[src]
impl<T> SaturatingAs for T
[src]pub fn saturating_as<Dst>(self) -> Dst where
T: SaturatingCast<Dst>,
[src]
pub fn saturating_as<Dst>(self) -> Dst where
T: SaturatingCast<Dst>,
[src]Casts the value.
impl<T> UnwrappedAs for T
[src]
impl<T> UnwrappedAs for T
[src]pub fn unwrapped_as<Dst>(self) -> Dst where
T: UnwrappedCast<Dst>,
[src]
pub fn unwrapped_as<Dst>(self) -> Dst where
T: UnwrappedCast<Dst>,
[src]Casts the value.
impl<T> WrappingAs for T
[src]
impl<T> WrappingAs for T
[src]pub fn wrapping_as<Dst>(self) -> Dst where
T: WrappingCast<Dst>,
[src]
pub fn wrapping_as<Dst>(self) -> Dst where
T: WrappingCast<Dst>,
[src]Casts the value.