[−][src]Struct nrf52811_hal::Twim
Interface to a TWIM instance.
This is a very basic interface that comes with the following limitation:
The TWIM instances share the same address space with instances of SPIM,
SPIS, SPI, TWIS, and TWI. For example, TWIM0 conflicts with SPIM0, SPIS0,
etc.; TWIM1 conflicts with SPIM1, SPIS1, etc. You need to make sure that
conflicting instances are disabled before using Twim
. Please refer to the
product specification for more information (section 15.2 for nRF52832,
section 6.1.2 for nRF52840).
Implementations
impl<T> Twim<T> where
T: Instance,
[src]
T: Instance,
pub fn new(twim: T, pins: Pins, frequency: FREQUENCY_A) -> Twim<T>
[src]
pub fn disable(&mut self)
[src]
Disable the instance.
Disabling the instance will switch off the peripheral leading to a considerably lower energy use. However, while the instance is disabled it is not possible to use it for communication. The configuration of the instance will be retained.
pub fn enable(&mut self)
[src]
Re-enable the instance after it was previously disabled.
pub fn write(&mut self, address: u8, buffer: &[u8]) -> Result<(), Error>
[src]
Write to an I2C slave.
The buffer must have a length of at most 255 bytes on the nRF52832 and at most 65535 bytes on the nRF52840.
pub fn read(&mut self, address: u8, buffer: &mut [u8]) -> Result<(), Error>
[src]
Read from an I2C slave.
The buffer must have a length of at most 255 bytes on the nRF52832 and at most 65535 bytes on the nRF52840.
pub fn write_then_read(
&mut self,
address: u8,
wr_buffer: &[u8],
rd_buffer: &mut [u8]
) -> Result<(), Error>
[src]
&mut self,
address: u8,
wr_buffer: &[u8],
rd_buffer: &mut [u8]
) -> Result<(), Error>
Write data to an I2C slave, then read data from the slave without triggering a stop condition between the two.
The buffers must have a length of at most 255 bytes on the nRF52832 and at most 65535 bytes on the nRF52840.
pub fn copy_write_then_read(
&mut self,
address: u8,
wr_buffer: &[u8],
rd_buffer: &mut [u8]
) -> Result<(), Error>
[src]
&mut self,
address: u8,
wr_buffer: &[u8],
rd_buffer: &mut [u8]
) -> Result<(), Error>
Copy data into RAM and write to an I2C slave, then read data from the slave without triggering a stop condition between the two.
The write buffer must have a length of at most 255 bytes on the nRF52832 and at most 1024 bytes on the nRF52840.
The read buffer must have a length of at most 255 bytes on the nRF52832 and at most 65535 bytes on the nRF52840.
pub fn free(self) -> T
[src]
Return the raw interface to the underlying TWIM peripheral.
Trait Implementations
impl<T> Read for Twim<T> where
T: Instance,
[src]
T: Instance,
type Error = Error
Error type
pub fn read(&mut self, addr: u8, bytes: &'w mut [u8]) -> Result<(), Error>
[src]
impl<T> Write for Twim<T> where
T: Instance,
[src]
T: Instance,
type Error = Error
Error type
pub fn write(&mut self, addr: u8, bytes: &'w [u8]) -> Result<(), Error>
[src]
impl<T> WriteRead for Twim<T> where
T: Instance,
[src]
T: Instance,
Auto Trait Implementations
impl<T> Send for Twim<T> where
T: Send,
T: Send,
impl<T> Sync for Twim<T> where
T: Sync,
T: Sync,
impl<T> Unpin for Twim<T> where
T: Unpin,
T: Unpin,
Blanket Implementations
impl<T> Any for T where
T: 'static + ?Sized,
[src]
T: 'static + ?Sized,
impl<T> Borrow<T> for T where
T: ?Sized,
[src]
T: ?Sized,
impl<T> BorrowMut<T> for T where
T: ?Sized,
[src]
T: ?Sized,
pub fn borrow_mut(&mut self) -> &mut T
[src]
impl<T> From<T> for T
[src]
impl<T, U> Into<U> for T where
U: From<T>,
[src]
U: From<T>,
impl<Src, Dst> LosslessTryInto<Dst> for Src where
Dst: LosslessTryFrom<Src>,
[src]
Dst: LosslessTryFrom<Src>,
pub fn lossless_try_into(self) -> Option<Dst>
[src]
impl<Src, Dst> LossyInto<Dst> for Src where
Dst: LossyFrom<Src>,
[src]
Dst: LossyFrom<Src>,
pub fn lossy_into(self) -> Dst
[src]
impl<T> Same<T> for T
type Output = T
Should always be Self
impl<T, U> TryFrom<U> for T where
U: Into<T>,
[src]
U: Into<T>,
type Error = Infallible
The type returned in the event of a conversion error.
pub fn try_from(value: U) -> Result<T, <T as TryFrom<U>>::Error>
[src]
impl<T, U> TryInto<U> for T where
U: TryFrom<T>,
[src]
U: TryFrom<T>,