Struct RoutingConfig

pub struct RoutingConfig {
    pub from: Option<String>,
    pub to: Option<String>,
    pub via: Option<String>,
    pub on_link: Option<bool>,
    pub metric: Option<u16>,
    pub type: Option<RouteType>,
    pub scope: Option<RouteScope>,
    pub table: Option<u16>,
    pub mtu: Option<u16>,
    pub congestion_window: Option<u16>,
    pub advertised_receive_window: Option<u16>,
}

The routes block defines standard static routes for an interface. At least to must be specified. If type is local or nat a default scope of host is assumed. If type is unicast and no gateway (via) is given or type is broadcast, multicast or anycast a default scope of link is assumend. Otherwise, a global scope is the default setting.

For from, to, and via, both IPv4 and IPv6 addresses are recognized, and must be in the form addr/prefixlen or addr.

Fields

from: Option<String>

Set a source IP address for traffic going through the route. (NetworkManager: as of v1.8.0)

to: Option<String>

Destination address for the route.

via: Option<String>

Address to the gateway to use for this route.

on_link: Option<bool>

When set to “true”, specifies that the route is directly connected to the interface. (NetworkManager: as of v1.12.0 for IPv4 and v1.18.0 for IPv6)

metric: Option<u16>

The relative priority of the route. Must be a positive integer value.

type: Option<RouteType>

The type of route. Valid options are “unicast” (default), “anycast”, “blackhole”, “broadcast”, “local”, “multicast”, “nat”, “prohibit”, “throw”, “unreachable” or “xresolve”.

scope: Option<RouteScope>

The route scope, how wide-ranging it is to the network. Possible values are “global”, “link”, or “host”.

table: Option<u16>

The table number to use for the route. In some scenarios, it may be useful to set routes in a separate routing table. It may also be used to refer to routing policy rules which also accept a table parameter. Allowed values are positive integers starting from 1. Some values are already in use to refer to specific routing tables: see /etc/iproute2/rt_tables. (NetworkManager: as of v1.10.0)

mtu: Option<u16>

The MTU to be used for the route, in bytes. Must be a positive integer value.

congestion_window: Option<u16>

The congestion window to be used for the route, represented by number of segments. Must be a positive integer value.

advertised_receive_window: Option<u16>

The receive window to be advertised for the route, represented by number of segments. Must be a positive integer value.

Trait Implementations

impl Clone for RoutingConfig

fn clone(&self) -> RoutingConfig

Returns a duplicate of the value.

fn clone_from(&mut self, source: &Self)

Performs copy-assignment from source.

impl Debug for RoutingConfig

fn fmt(&self, f: &mut Formatter<'_>) -> Result

Formats the value using the given formatter.

impl Default for RoutingConfig

fn default() -> RoutingConfig

Returns the “default value” for a type.

impl<'de> Deserialize<'de> for RoutingConfig

fn deserialize<__D>(__deserializer: __D) -> Result<Self, __D::Error>

where __D: Deserializer<'de>,

Deserialize this value from the given Serde deserializer.

impl PartialEq for RoutingConfig

fn eq(&self, other: &RoutingConfig) -> bool

Tests for self and other values to be equal, and is used by ==.

fn ne(&self, other: &Rhs) -> bool

Tests for !=. The default implementation is almost always sufficient, and should not be overridden without very good reason.

impl Serialize for RoutingConfig

fn serialize<__S>(&self, __serializer: __S) -> Result<__S::Ok, __S::Error>

where __S: Serializer,

Serialize this value into the given Serde serializer.

impl Eq for RoutingConfig

impl StructuralPartialEq for RoutingConfig