Struct ltc681x::monitor::LTC681X

pub struct LTC681X<B, CS, P, T, const L: usize>
where
    B: Transfer<u8>,
    CS: OutputPin,
    P: PollMethod<CS>,
    T: DeviceTypes,
{ /* private fields */ }

Client for LTC681X IC

Implementations

impl<B, CS, const L: usize> LTC681X<B, CS, NoPolling, LTC6810, L>

where B: Transfer<u8>, CS: OutputPin,

pub fn ltc6810(bus: B, cs: CS) -> Self

Creates a client instant for LTC6810 variant

impl<B, CS, const L: usize> LTC681X<B, CS, NoPolling, LTC6811, L>

where B: Transfer<u8>, CS: OutputPin,

pub fn ltc6811(bus: B, cs: CS) -> Self

Creates a client instant for LTC6811 variant

impl<B, CS, const L: usize> LTC681X<B, CS, NoPolling, LTC6812, L>

where B: Transfer<u8>, CS: OutputPin,

pub fn ltc6812(bus: B, cs: CS) -> Self

Creates a client instant for LTC6812 variant

impl<B, CS, const L: usize> LTC681X<B, CS, NoPolling, LTC6813, L>

where B: Transfer<u8>, CS: OutputPin,

pub fn ltc6813(bus: B, cs: CS) -> Self

Creates a client instant for LTC6813 variant

impl<B, CS, P, T, const L: usize> LTC681X<B, CS, P, T, L>

where B: Transfer<u8>, CS: OutputPin, P: PollMethod<CS>, T: DeviceTypes,

pub fn enable_sdo_polling(self) -> LTC681X<B, CS, SDOLinePolling, T, L>

Enables SDO ADC polling

After entering a conversion command, the SDO line is driven low when the device is busy performing conversions. SDO is pulled high when the device completes conversions.

Trait Implementations

impl<B, CS, P, T, const L: usize> LTC681XClient<T, L> for LTC681X<B, CS, P, T, L>

where B: Transfer<u8>, CS: OutputPin, P: PollMethod<CS>, T: DeviceTypes,

fn start_conv_cells( &mut self, mode: ADCMode, cells: T::CellSelection, dcp: bool ) -> Result<CommandTime, Error<B, CS>>

See LTC681XClient::start_conv_cells

fn start_conv_gpio( &mut self, mode: ADCMode, channels: T::GPIOSelection ) -> Result<CommandTime, Error<B, CS>>

See LTC681XClient::start_conv_gpio

fn start_overlap_measurement( &mut self, mode: ADCMode, dcp: bool ) -> Result<(), Error<B, CS>>

See LTC681XClient::start_conv_gpio

fn measure_internal_parameters( &mut self, mode: ADCMode, group: StatusGroup ) -> Result<CommandTime, Error<B, CS>>

See LTC681XClient::start_conv_gpio

fn read_register( &mut self, register: T::Register ) -> Result<[[u16; 3]; L], Error<B, CS>>

See LTC681XClient::read_cell_voltages

fn write_register( &mut self, register: T::Register, data: [[u8; 6]; L] ) -> Result<(), Error<B, CS>>

See LTC681XClient::read_cell_voltages

fn write_configuration( &mut self, config: [Configuration; L] ) -> Result<(), Self::Error>

See LTC681XClient::read_cell_voltages

fn read_voltages<R: RegisterLocator<T> + 'static>( &mut self, locator: R ) -> Result<Vec<Vec<Voltage<T>, 18>, L>, Self::Error>

where T: 'static,

See LTC681XClient::read_cell_voltages

fn read_overlap_result(&mut self) -> Result<[[u16; 4]; L], Self::Error>

See LTC681XClient::read_cell_voltages

fn read_internal_device_parameters( &mut self ) -> Result<Vec<InternalDeviceParameters, L>, Self::Error>

See LTC681XClient::read_cell_voltages

type Error = Error<B, CS>

impl<B, CS, T, const L: usize> PollClient for LTC681X<B, CS, SDOLinePolling, T, L>

where B: Transfer<u8>, CS: OutputPin, T: DeviceTypes,

fn adc_ready(&mut self) -> Result<bool, Self::Error>

Returns false if the ADC is busy If ADC is ready, CS line is pulled high

type Error = Error<B, CS>