Struct lpc81x_pac::lpc811::usart0::stat::W

impl W

pub fn deltacts(&mut self) -> DELTACTS_W<'_, 5>

Bit 5 - This bit is set when a change in the state is detected for the CTS flag above. This bit is cleared by software.

pub fn overrunint(&mut self) -> OVERRUNINT_W<'_, 8>

Bit 8 - Overrun Error interrupt flag. This flag is set when a new character is received while the receiver buffer is still in use. If this occurs, the newly received character in the shift register is lost.

pub fn deltarxbrk(&mut self) -> DELTARXBRK_W<'_, 11>

Bit 11 - This bit is set when a change in the state of receiver break detection occurs.Cleared by software.

pub fn start(&mut self) -> START_W<'_, 12>

Bit 12 - This bit is set when a start is detected on the receiver input. Its purpose is primarily to allow wake-up from Deep-sleep or Power-down mode immediately when a start is detected. Cleared by software.

pub fn framerrint(&mut self) -> FRAMERRINT_W<'_, 13>

Bit 13 - Framing Error interrupt flag. This flag is set when a character is received with a missing stop bit at the expected location. This could be an indication of a baud rate or configuration mismatch with the transmitting source.

pub fn parityerrint(&mut self) -> PARITYERRINT_W<'_, 14>

Bit 14 - Parity Error interrupt flag. This flag is set when a parity error is detected in a received character.

pub fn rxnoiseint(&mut self) -> RXNOISEINT_W<'_, 15>

Bit 15 - Received Noise interrupt flag. Three samples of received data are taken in order to determine the value of each received data bit, except in synchronous mode. This acts as a noise filter if one sample disagrees. This flag is set when a received data bit contains one disagreeing sample. This could indicate line noise, a baud rate or character format mismatch, or loss of synchronization during data reception.

pub unsafe fn bits(&mut self, bits: u32) -> &mut Self

Writes raw bits to the register.

Methods from Deref<Target = W<STAT_SPEC>>§

pub unsafe fn bits(&mut self, bits: REG::Ux) -> &mut Self

Writes raw bits to the register.

Examples found in repository ?

src/lpc810/gpio/b0_0.rs (line 57)

    pub unsafe fn bits(&mut self, bits: u8) -> &mut Self {
        self.0.bits(bits);
        self
    }

More examples

Hide additional examples

src/lpc810/gpio/b0_1.rs (line 57)

    pub unsafe fn bits(&mut self, bits: u8) -> &mut Self {
        self.0.bits(bits);
        self
    }

src/lpc810/gpio/b0_10.rs (line 57)

    pub unsafe fn bits(&mut self, bits: u8) -> &mut Self {
        self.0.bits(bits);
        self
    }

src/lpc810/gpio/b0_11.rs (line 57)

    pub unsafe fn bits(&mut self, bits: u8) -> &mut Self {
        self.0.bits(bits);
        self
    }

src/lpc810/gpio/b0_12.rs (line 57)

    pub unsafe fn bits(&mut self, bits: u8) -> &mut Self {
        self.0.bits(bits);
        self
    }

src/lpc810/gpio/b0_13.rs (line 57)

    pub unsafe fn bits(&mut self, bits: u8) -> &mut Self {
        self.0.bits(bits);
        self
    }

Additional examples can be found in:

Trait Implementations§

impl Deref for W

type Target = W<STAT_SPEC>

The resulting type after dereferencing.

fn deref(&self) -> &Self::Target

Dereferences the value.

impl DerefMut for W

fn deref_mut(&mut self) -> &mut Self::Target

Mutably dereferences the value.

impl From<W<STAT_SPEC>> for W

fn from(writer: W<STAT_SPEC>) -> Self

Converts to this type from the input type.

Auto Trait Implementations§

impl UnwindSafe for W

Blanket Implementations§

impl<T> Any for Twhere
T: 'static + ?Sized,

fn type_id(&self) -> TypeId

Gets the TypeId of self. Read more

impl<T> Borrow<T> for Twhere
T: ?Sized,

const: unstable · source§

fn borrow(&self) -> &T

Immutably borrows from an owned value. Read more

impl<T> BorrowMut<T> for Twhere
T: ?Sized,

const: unstable · source§

fn borrow_mut(&mut self) -> &mut T

Mutably borrows from an owned value. Read more

impl<T> From<T> for T

const: unstable · source§

fn from(t: T) -> T

Returns the argument unchanged.

impl<T, U> Into for Twhere
U: From<T>,

const: unstable · source§

fn into(self) -> U

Calls U::from(self).

That is, this conversion is whatever the implementation of From<T> for U chooses to do.

impl<T, U> TryFrom for Twhere
U: Into<T>,

type Error = Infallible

The type returned in the event of a conversion error.

const: unstable · source§

fn try_from(value: U) -> Result<T, <T as TryFrom>::Error>

Performs the conversion.

impl<T, U> TryInto for Twhere
U: TryFrom<T>,