Struct grep_pcre2::RegexMatcherBuilder

pub struct RegexMatcherBuilder { /* private fields */ }

A builder for configuring the compilation of a PCRE2 regex.

Implementations

impl RegexMatcherBuilder

pub fn new() -> RegexMatcherBuilder

Create a new matcher builder with a default configuration.

pub fn build(&self, pattern: &str) -> Result<RegexMatcher, Error>

Compile the given pattern into a PCRE matcher using the current configuration.

If there was a problem compiling the pattern, then an error is returned.

pub fn build_many<P: AsRef<str>>( &self, patterns: &[P] ) -> Result<RegexMatcher, Error>

Compile all of the given patterns into a single regex that matches when at least one of the patterns matches.

If there was a problem building the regex, then an error is returned.

pub fn caseless(&mut self, yes: bool) -> &mut RegexMatcherBuilder

Enables case insensitive matching.

If the utf option is also set, then Unicode case folding is used to determine case insensitivity. When the utf option is not set, then only standard ASCII case insensitivity is considered.

This option corresponds to the i flag.

pub fn case_smart(&mut self, yes: bool) -> &mut RegexMatcherBuilder

Whether to enable “smart case” or not.

When smart case is enabled, the builder will automatically enable case insensitive matching based on how the pattern is written. Namely, case insensitive mode is enabled when both of the following things are believed to be true:

1. The pattern contains at least one literal character. For example, a\w contains a literal (a) but \w does not.
2. Of the literals in the pattern, none of them are considered to be uppercase according to Unicode. For example, foo\pL has no uppercase literals but Foo\pL does.

Note that the implementation of this is not perfect. Namely, \p{Ll} will prevent case insensitive matching even though it is part of a meta sequence. This bug will probably never be fixed.

pub fn dotall(&mut self, yes: bool) -> &mut RegexMatcherBuilder

Enables “dot all” matching.

When enabled, the . metacharacter in the pattern matches any character, include \n. When disabled (the default), . will match any character except for \n.

This option corresponds to the s flag.

pub fn extended(&mut self, yes: bool) -> &mut RegexMatcherBuilder

Enable “extended” mode in the pattern, where whitespace is ignored.

This option corresponds to the x flag.

pub fn multi_line(&mut self, yes: bool) -> &mut RegexMatcherBuilder

Enable multiline matching mode.

When enabled, the ^ and $ anchors will match both at the beginning and end of a subject string, in addition to matching at the start of a line and the end of a line. When disabled, the ^ and $ anchors will only match at the beginning and end of a subject string.

This option corresponds to the m flag.

pub fn crlf(&mut self, yes: bool) -> &mut RegexMatcherBuilder

Enable matching of CRLF as a line terminator.

When enabled, anchors such as ^ and $ will match any of the following as a line terminator: \r, \n or \r\n.

This is disabled by default, in which case, only \n is recognized as a line terminator.

pub fn word(&mut self, yes: bool) -> &mut RegexMatcherBuilder

Require that all matches occur on word boundaries.

Enabling this option is subtly different than putting \b assertions on both sides of your pattern. In particular, a \b assertion requires that one side of it match a word character while the other match a non-word character. This option, in contrast, merely requires that one side match a non-word character.

For example, \b-2\b will not match foo -2 bar since - is not a word character. However, -2 with this word option enabled will match the -2 in foo -2 bar.

pub fn fixed_strings(&mut self, yes: bool) -> &mut RegexMatcherBuilder

Whether the patterns should be treated as literal strings or not. When this is active, all characters, including ones that would normally be special regex meta characters, are matched literally.

pub fn whole_line(&mut self, yes: bool) -> &mut RegexMatcherBuilder

Whether each pattern should match the entire line or not. This is equivalent to surrounding the pattern with (?m:^) and (?m:$).

pub fn ucp(&mut self, yes: bool) -> &mut RegexMatcherBuilder

Enable Unicode matching mode.

When enabled, the following patterns become Unicode aware: \b, \B, \d, \D, \s, \S, \w, \W.

When set, this implies UTF matching mode. It is not possible to enable Unicode matching mode without enabling UTF matching mode.

This is disabled by default.

pub fn utf(&mut self, yes: bool) -> &mut RegexMatcherBuilder

Enable UTF matching mode.

When enabled, characters are treated as sequences of code units that make up a single codepoint instead of as single bytes. For example, this will cause . to match any single UTF-8 encoded codepoint, where as when this is disabled, . will any single byte (except for \n in both cases, unless “dot all” mode is enabled).

Note that when UTF matching mode is enabled, every search performed will do a UTF-8 validation check, which can impact performance. The UTF-8 check can be disabled via the disable_utf_check option, but it is undefined behavior to enable UTF matching mode and search invalid UTF-8.

This is disabled by default.

pub fn disable_utf_check(&mut self) -> &mut RegexMatcherBuilder

👎Deprecated since 0.2.4: now a no-op due to new PCRE2 features

This is now deprecated and is a no-op.

Previously, this option permitted disabling PCRE2’s UTF-8 validity check, which could result in undefined behavior if the haystack was not valid UTF-8. But PCRE2 introduced a new option, PCRE2_MATCH_INVALID_UTF, in 10.34 which this crate always sets. When this option is enabled, PCRE2 claims to not have undefined behavior when the haystack is invalid UTF-8.

Therefore, disabling the UTF-8 check is not something that is exposed by this crate.

pub fn jit(&mut self, yes: bool) -> &mut RegexMatcherBuilder

Enable PCRE2’s JIT and return an error if it’s not available.

This generally speeds up matching quite a bit. The downside is that it can increase the time it takes to compile a pattern.

If the JIT isn’t available or if JIT compilation returns an error, then regex compilation will fail with the corresponding error.

This is disabled by default, and always overrides jit_if_available.

pub fn jit_if_available(&mut self, yes: bool) -> &mut RegexMatcherBuilder

Enable PCRE2’s JIT if it’s available.

This generally speeds up matching quite a bit. The downside is that it can increase the time it takes to compile a pattern.

If the JIT isn’t available or if JIT compilation returns an error, then a debug message with the error will be emitted and the regex will otherwise silently fall back to non-JIT matching.

This is disabled by default, and always overrides jit.

pub fn max_jit_stack_size( &mut self, bytes: Option<usize> ) -> &mut RegexMatcherBuilder

Set the maximum size of PCRE2’s JIT stack, in bytes. If the JIT is not enabled, then this has no effect.

When None is given, no custom JIT stack will be created, and instead, the default JIT stack is used. When the default is used, its maximum size is 32 KB.

When this is set, then a new JIT stack will be created with the given maximum size as its limit.

Increasing the stack size can be useful for larger regular expressions.

By default, this is set to None.

Trait Implementations

impl Clone for RegexMatcherBuilder

fn clone(&self) -> RegexMatcherBuilder

Returns a copy of the value.

fn clone_from(&mut self, source: &Self)

Performs copy-assignment from source.

impl Debug for RegexMatcherBuilder

fn fmt(&self, f: &mut Formatter<'_>) -> Result

Formats the value using the given formatter.