Struct esp32s3::io_mux::gpio::W

source · [−]

pub struct W(_);

Expand description

Register GPIO%s writer

Implementations

source

impl W

source

pub fn mcu_oe(&mut self) -> MCU_OE_W<'_, 0>

Bit 0 - Output enable of the pad in sleep mode. 1: output enabled; 0: output disabled.

source

pub fn slp_sel(&mut self) -> SLP_SEL_W<'_, 1>

Bit 1 - Sleep mode selection of this pad. Set to 1 to put the pad in pad mode.

source

pub fn mcu_wpd(&mut self) -> MCU_WPD_W<'_, 2>

Bit 2 - Pull-down enable of the pad in sleep mode. 1: internal pull-down enabled; 0: internal pull-down disabled.

source

pub fn mcu_wpu(&mut self) -> MCU_WPU_W<'_, 3>

Bit 3 - Pull-up enable of the pad during sleep mode. 1: internal pull-up enabled; 0: internal pull-up disabled.

source

pub fn mcu_ie(&mut self) -> MCU_IE_W<'_, 4>

Bit 4 - Input enable of the pad during sleep mode. 1: input enabled; 0: input disabled.

source

pub fn fun_wpd(&mut self) -> FUN_WPD_W<'_, 7>

Bit 7 - Pull-down enable of the pad. 1: internal pull-down enabled; 0: internal pull-down disabled.

source

pub fn fun_wpu(&mut self) -> FUN_WPU_W<'_, 8>

Bit 8 - Pull-up enable of the pad. 1: internal pull-up enabled; 0: internal pull-up disabled.

source

pub fn fun_ie(&mut self) -> FUN_IE_W<'_, 9>

Bit 9 - Input enable of the pad. 1: input enabled; 0: input disabled.

source

pub fn fun_drv(&mut self) -> FUN_DRV_W<'_, 10>

Bits 10:11 - Select the drive strength of the pad. 0: ~5 mA; 1: ~10mA; 2: ~20mA; 3: ~40mA.

source

pub fn mcu_sel(&mut self) -> MCU_SEL_W<'_, 12>

Bits 12:14 - Select IO MUX function for this signal. 0: Select Function 1; 1: Select Function 2; etc.

source

pub fn filter_en(&mut self) -> FILTER_EN_W<'_, 15>

Bit 15 - Enable filter for pin input signals. 1: Filter enabled; 2: Filter disabled.

source

pub unsafe fn bits(&mut self, bits: u32) -> &mut Self

Writes raw bits to the register.

Methods from Deref<Target = W<GPIO_SPEC>>

source

pub unsafe fn bits(&mut self, bits: REG::Ux) -> &mut Self

Writes raw bits to the register.

Trait Implementations

source

impl Deref for W

type Target = W<GPIO_SPEC>

The resulting type after dereferencing.

source

fn deref(&self) -> &Self::Target

Dereferences the value.

source

impl DerefMut for W

source

fn deref_mut(&mut self) -> &mut Self::Target

Mutably dereferences the value.

source

impl From<W<GPIO_SPEC>> for W

source

fn from(writer: W<GPIO_SPEC>) -> Self

Converts to this type from the input type.

Auto Trait Implementations

impl RefUnwindSafe for W

impl Send for W

impl Sync for W

impl Unpin for W

impl UnwindSafe for W

Blanket Implementations

source

impl<T> Any for T where
T: 'static + ?Sized,

source

fn type_id(&self) -> TypeId

Gets the TypeId of self. Read more

source

impl<T> Borrow<T> for T where
T: ?Sized,

const: unstable · source

fn borrow(&self) -> &T

Immutably borrows from an owned value. Read more

source

impl<T> BorrowMut<T> for T where
T: ?Sized,

const: unstable · source

fn borrow_mut(&mut self) -> &mut T

Mutably borrows from an owned value. Read more

source

impl<T> From<T> for T

const: unstable · source

fn from(t: T) -> T

Returns the argument unchanged.

source

impl<T, U> Into for T where
U: From<T>,

const: unstable · source

fn into(self) -> U

Calls U::from(self).

That is, this conversion is whatever the implementation of From<T> for U chooses to do.

source

impl<T, U> TryFrom for T where
U: Into<T>,

type Error = Infallible

The type returned in the event of a conversion error.

const: unstable · source

fn try_from(value: U) -> Result<T, <T as TryFrom>::Error>

Performs the conversion.

source

impl<T, U> TryInto for T where
U: TryFrom<T>,

type Error = >::Error

The type returned in the event of a conversion error.

const: unstable · source

fn try_into(self) -> Result<U, >::Error>

Performs the conversion.

Struct esp32s3::io_mux::gpio::W

Implementations

impl W

pub fn mcu_oe(&mut self) -> MCU_OE_W<'_, 0>

pub fn slp_sel(&mut self) -> SLP_SEL_W<'_, 1>

pub fn mcu_wpd(&mut self) -> MCU_WPD_W<'_, 2>

pub fn mcu_wpu(&mut self) -> MCU_WPU_W<'_, 3>

pub fn mcu_ie(&mut self) -> MCU_IE_W<'_, 4>

pub fn fun_wpd(&mut self) -> FUN_WPD_W<'_, 7>

pub fn fun_wpu(&mut self) -> FUN_WPU_W<'_, 8>

pub fn fun_ie(&mut self) -> FUN_IE_W<'_, 9>

pub fn fun_drv(&mut self) -> FUN_DRV_W<'_, 10>

pub fn mcu_sel(&mut self) -> MCU_SEL_W<'_, 12>

pub fn filter_en(&mut self) -> FILTER_EN_W<'_, 15>

pub unsafe fn bits(&mut self, bits: u32) -> &mut Self

Methods from Deref<Target = W<GPIO_SPEC>>

pub unsafe fn bits(&mut self, bits: REG::Ux) -> &mut Self

Trait Implementations

impl Deref for W

type Target = W<GPIO_SPEC>

fn deref(&self) -> &Self::Target

impl DerefMut for W

fn deref_mut(&mut self) -> &mut Self::Target

impl From<W<GPIO_SPEC>> for W

fn from(writer: W<GPIO_SPEC>) -> Self

Auto Trait Implementations

impl RefUnwindSafe for W

impl Send for W

impl Sync for W

impl Unpin for W

impl UnwindSafe for W

Blanket Implementations

impl<T> Any for T where T: 'static + ?Sized,

fn type_id(&self) -> TypeId

impl<T> Borrow<T> for T where T: ?Sized,

fn borrow(&self) -> &T

impl<T> BorrowMut<T> for T where T: ?Sized,

fn borrow_mut(&mut self) -> &mut T

impl<T> From<T> for T

fn from(t: T) -> T

impl<T, U> Into<U> for T where U: From<T>,

fn into(self) -> U

impl<T, U> TryFrom<U> for T where U: Into<T>,

type Error = Infallible

fn try_from(value: U) -> Result<T, <T as TryFrom<U>>::Error>

impl<T, U> TryInto<U> for T where U: TryFrom<T>,

type Error = <U as TryFrom<T>>::Error

fn try_into(self) -> Result<U, <U as TryFrom<T>>::Error>

impl<T> Any for T where
T: 'static + ?Sized,

impl<T> Borrow<T> for T where
T: ?Sized,

impl<T> BorrowMut<T> for T where
T: ?Sized,

impl<T, U> Into<U> for T where
U: From<T>,

impl<T, U> TryFrom<U> for T where
U: Into<T>,

impl<T, U> TryInto<U> for T where
U: TryFrom<T>,