Struct esp32s3_hal::pac::i2s1::rx_conf::W

pub struct W(_);

Register RX_CONF writer

Implementations

impl W

pub fn rx_reset(&mut self) -> BitWriterRaw<'_, u32, RX_CONF_SPEC, bool, BitM, 0>

Bit 0 - Set this bit to reset receiver

pub fn rx_fifo_reset(
    &mut self
) -> BitWriterRaw<'_, u32, RX_CONF_SPEC, bool, BitM, 1>

Bit 1 - Set this bit to reset Rx AFIFO

pub fn rx_start(&mut self) -> BitWriterRaw<'_, u32, RX_CONF_SPEC, bool, BitM, 2>

Bit 2 - Set this bit to start receiving data

pub fn rx_slave_mod(
    &mut self
) -> BitWriterRaw<'_, u32, RX_CONF_SPEC, bool, BitM, 3>

Bit 3 - Set this bit to enable slave receiver mode

pub fn rx_mono(&mut self) -> BitWriterRaw<'_, u32, RX_CONF_SPEC, bool, BitM, 5>

Bit 5 - Set this bit to enable receiver in mono mode

pub fn rx_big_endian(
    &mut self
) -> BitWriterRaw<'_, u32, RX_CONF_SPEC, bool, BitM, 7>

Bit 7 - I2S Rx byte endian, 1: low addr value to high addr. 0: low addr with low addr value.

pub fn rx_update(
    &mut self
) -> BitWriterRaw<'_, u32, RX_CONF_SPEC, bool, BitM, 8>

Bit 8 - Set 1 to update I2S RX registers from APB clock domain to I2S RX clock domain. This bit will be cleared by hardware after update register done.

pub fn rx_mono_fst_vld(
    &mut self
) -> BitWriterRaw<'_, u32, RX_CONF_SPEC, bool, BitM, 9>

Bit 9 - 1: The first channel data value is valid in I2S RX mono mode. 0: The second channel data value is valid in I2S RX mono mode.

pub fn rx_pcm_conf(
    &mut self
) -> FieldWriterRaw<'_, u32, RX_CONF_SPEC, u8, u8, Unsafe, 2, 10>

Bits 10:11 - I2S RX compress/decompress configuration bit. & 0 (atol): A-Law decompress, 1 (ltoa) : A-Law compress, 2 (utol) : u-Law decompress, 3 (ltou) : u-Law compress. &

pub fn rx_pcm_bypass(
    &mut self
) -> BitWriterRaw<'_, u32, RX_CONF_SPEC, bool, BitM, 12>

Bit 12 - Set this bit to bypass Compress/Decompress module for received data.

pub fn rx_stop_mode(
    &mut self
) -> FieldWriterRaw<'_, u32, RX_CONF_SPEC, u8, u8, Unsafe, 2, 13>

Bits 13:14 - 0 : I2S Rx only stop when reg_rx_start is cleared. 1: Stop when reg_rx_start is 0 or in_suc_eof is 1. 2: Stop I2S RX when reg_rx_start is 0 or RX FIFO is full.

pub fn rx_left_align(
    &mut self
) -> BitWriterRaw<'_, u32, RX_CONF_SPEC, bool, BitM, 15>

Bit 15 - 1: I2S RX left alignment mode. 0: I2S RX right alignment mode.

pub fn rx_24_fill_en(
    &mut self
) -> BitWriterRaw<'_, u32, RX_CONF_SPEC, bool, BitM, 16>

Bit 16 - 1: store 24 channel bits to 32 bits. 0:store 24 channel bits to 24 bits.

pub fn rx_ws_idle_pol(
    &mut self
) -> BitWriterRaw<'_, u32, RX_CONF_SPEC, bool, BitM, 17>

Bit 17 - 0: WS should be 0 when receiving left channel data, and WS is 1in right channel. 1: WS should be 1 when receiving left channel data, and WS is 0in right channel.

pub fn rx_bit_order(
    &mut self
) -> BitWriterRaw<'_, u32, RX_CONF_SPEC, bool, BitM, 18>

Bit 18 - I2S Rx bit endian. 1:small endian, the LSB is received first. 0:big endian, the MSB is received first.

pub fn rx_tdm_en(
    &mut self
) -> BitWriterRaw<'_, u32, RX_CONF_SPEC, bool, BitM, 19>

Bit 19 - 1: Enable I2S TDM Rx mode . 0: Disable.

pub fn rx_pdm_en(
    &mut self
) -> BitWriterRaw<'_, u32, RX_CONF_SPEC, bool, BitM, 20>

Bit 20 - 1: Enable I2S PDM Rx mode . 0: Disable.

pub unsafe fn bits(&mut self, bits: u32) -> &mut W

Writes raw bits to the register.

Methods from Deref<Target = W<RX_CONF_SPEC>>

pub unsafe fn bits(&mut self, bits: <REG as RegisterSpec>::Ux) -> &mut W<REG>

Writes raw bits to the register.

Safety

Read datasheet or reference manual to find what values are allowed to pass.

Trait Implementations

impl Deref for W

type Target = W<RX_CONF_SPEC>

The resulting type after dereferencing.

fn deref(&self) -> &<W as Deref>::Target

Dereferences the value.

impl DerefMut for W

fn deref_mut(&mut self) -> &mut <W as Deref>::Target

Mutably dereferences the value.

impl From<W<RX_CONF_SPEC>> for W

fn from(writer: W<RX_CONF_SPEC>) -> W

Converts to this type from the input type.