Struct esp32s2::efuse::rd_repeat_data1::R

pub struct R(_);

Register RD_REPEAT_DATA1 reader

Implementations

impl R

pub fn vdd_spi_drefm(&self) -> VDD_SPI_DREFM_R

Bits 0:1 - SPI regulator medium voltage reference.

pub fn vdd_spi_drefl(&self) -> VDD_SPI_DREFL_R

Bits 2:3 - SPI regulator low voltage reference.

pub fn vdd_spi_xpd(&self) -> VDD_SPI_XPD_R

Bit 4 - If VDD_SPI_FORCE is 1, this value determines if the VDD_SPI regulator is powered on.

pub fn vdd_spi_tieh(&self) -> VDD_SPI_TIEH_R

Bit 5 - If VDD_SPI_FORCE is 1, determines VDD_SPI voltage. 0: VDD_SPI connects to 1.8 V LDO. 1: VDD_SPI connects to VDD_RTC_IO.

pub fn vdd_spi_force(&self) -> VDD_SPI_FORCE_R

Bit 6 - Set this bit to use XPD_VDD_PSI_REG and VDD_SPI_TIEH to configure VDD_SPI LDO.

pub fn vdd_spi_en_init(&self) -> VDD_SPI_EN_INIT_R

Bit 7 - Set SPI regulator to 0 to configure init[1:0]=0.

pub fn vdd_spi_encurlim(&self) -> VDD_SPI_ENCURLIM_R

Bit 8 - Set SPI regulator to 1 to enable output current limit.

pub fn vdd_spi_dcurlim(&self) -> VDD_SPI_DCURLIM_R

Bits 9:11 - Tunes the current limit threshold of SPI regulator when tieh=0, about 800 mA/(8+d).

pub fn vdd_spi_init(&self) -> VDD_SPI_INIT_R

Bits 12:13 - Adds resistor from LDO output to ground. 0: no resistance. 1: 6 K. 2: 4 K. 3: 2 K.

pub fn vdd_spi_dcap(&self) -> VDD_SPI_DCAP_R

Bits 14:15 - Prevents SPI regulator from overshoot.

pub fn wdt_delay_sel(&self) -> WDT_DELAY_SEL_R

Bits 16:17 - Selects RTC watchdog timeout threshold at startup. 0: 40,000 slow clock cycles. 1: 80,000 slow clock cycles. 2: 160,000 slow clock cycles. 3: 320,000 slow clock cycles.

pub fn spi_boot_crypt_cnt(&self) -> SPI_BOOT_CRYPT_CNT_R

Bits 18:20 - Enables encryption and decryption, when an SPI boot mode is set. Feature is enabled 1 or 3 bits are set in the eFuse, disabled otherwise.

pub fn secure_boot_key_revoke0(&self) -> SECURE_BOOT_KEY_REVOKE0_R

Bit 21 - If set, revokes use of secure boot key digest 0.

pub fn secure_boot_key_revoke1(&self) -> SECURE_BOOT_KEY_REVOKE1_R

Bit 22 - If set, revokes use of secure boot key digest 1.

pub fn secure_boot_key_revoke2(&self) -> SECURE_BOOT_KEY_REVOKE2_R

Bit 23 - If set, revokes use of secure boot key digest 2.

pub fn key_purpose_0(&self) -> KEY_PURPOSE_0_R

Bits 24:27 - Purpose of KEY0. Refer to Table Key Purpose Values.

pub fn key_purpose_1(&self) -> KEY_PURPOSE_1_R

Bits 28:31 - Purpose of KEY1. Refer to Table Key Purpose Values.

Methods from Deref<Target = R<RD_REPEAT_DATA1_SPEC>>

pub fn bits(&self) -> REG::Ux

Reads raw bits from register.

Trait Implementations

impl Deref for R

type Target = R<RD_REPEAT_DATA1_SPEC>

The resulting type after dereferencing.

fn deref(&self) -> &Self::Target

Dereferences the value.

impl From<R<RD_REPEAT_DATA1_SPEC>> for R

fn from(reader: R<RD_REPEAT_DATA1_SPEC>) -> Self

Converts to this type from the input type.