Struct esp32s2_hal::peripherals::RTC_I2C
source · pub struct RTC_I2C { /* private fields */ }
Implementations§
source§impl RTC_I2C
impl RTC_I2C
sourcepub unsafe fn steal() -> RTC_I2C
pub unsafe fn steal() -> RTC_I2C
Unsafely create an instance of this peripheral out of thin air.
Safety
You must ensure that you’re only using one instance of this type at a time.
Methods from Deref<Target = RegisterBlock>§
pub fn scl_low(&self) -> &Reg<SCL_LOW_SPEC>
pub fn scl_low(&self) -> &Reg<SCL_LOW_SPEC>
0x00 - Configure the low level width of SCL
pub fn ctrl(&self) -> &Reg<CTRL_SPEC>
pub fn ctrl(&self) -> &Reg<CTRL_SPEC>
0x04 - Transmission setting
pub fn status(&self) -> &Reg<STATUS_SPEC>
pub fn status(&self) -> &Reg<STATUS_SPEC>
0x08 - RTC I2C status
pub fn to(&self) -> &Reg<TO_SPEC>
pub fn to(&self) -> &Reg<TO_SPEC>
0x0c - Configure RTC I2C timeout
pub fn slave_addr(&self) -> &Reg<SLAVE_ADDR_SPEC>
pub fn slave_addr(&self) -> &Reg<SLAVE_ADDR_SPEC>
0x10 - Configure slave address
pub fn scl_high(&self) -> &Reg<SCL_HIGH_SPEC>
pub fn scl_high(&self) -> &Reg<SCL_HIGH_SPEC>
0x14 - Configure the high level width of SCL
pub fn sda_duty(&self) -> &Reg<SDA_DUTY_SPEC>
pub fn sda_duty(&self) -> &Reg<SDA_DUTY_SPEC>
0x18 - Configure the SDA hold time after a negative SCL edge
pub fn scl_start_period(&self) -> &Reg<SCL_START_PERIOD_SPEC>
pub fn scl_start_period(&self) -> &Reg<SCL_START_PERIOD_SPEC>
0x1c - Configure the delay between the SDA and SCL negative edge for a start condition
pub fn scl_stop_period(&self) -> &Reg<SCL_STOP_PERIOD_SPEC>
pub fn scl_stop_period(&self) -> &Reg<SCL_STOP_PERIOD_SPEC>
0x20 - Configure the delay between SDA and SCL positive edge for a stop condition
pub fn int_clr(&self) -> &Reg<INT_CLR_SPEC>
pub fn int_clr(&self) -> &Reg<INT_CLR_SPEC>
0x24 - Clear RTC I2C interrupt
pub fn int_raw(&self) -> &Reg<INT_RAW_SPEC>
pub fn int_raw(&self) -> &Reg<INT_RAW_SPEC>
0x28 - RTC I2C raw interrupt
pub fn int_st(&self) -> &Reg<INT_ST_SPEC>
pub fn int_st(&self) -> &Reg<INT_ST_SPEC>
0x2c - RTC I2C interrupt status
pub fn int_ena(&self) -> &Reg<INT_ENA_SPEC>
pub fn int_ena(&self) -> &Reg<INT_ENA_SPEC>
0x30 - Enable RTC I2C interrupt
pub fn data(&self) -> &Reg<DATA_SPEC>
pub fn data(&self) -> &Reg<DATA_SPEC>
0x34 - RTC I2C read data
pub fn cmd_iter(&self) -> impl Iterator<Item = &Reg<CMD_SPEC>>
pub fn cmd_iter(&self) -> impl Iterator<Item = &Reg<CMD_SPEC>>
Iterator for array of: 0x38..0x78 - RTC I2C Command %s
pub fn date(&self) -> &Reg<DATE_SPEC>
pub fn date(&self) -> &Reg<DATE_SPEC>
0xfc - Version control register