Module esp32h2::uart0::conf0

a

Structs

• CONF0_SPEC
  a

Type Aliases

• AUTOBAUD_EN_R
  Field AUTOBAUD_EN reader - This is the enable bit for detecting baudrate.
• AUTOBAUD_EN_W
  Field AUTOBAUD_EN writer - This is the enable bit for detecting baudrate.
• BIT_NUM_R
  Field BIT_NUM reader - This register is used to set the length of data.
• BIT_NUM_W
  Field BIT_NUM writer - This register is used to set the length of data.
• DIS_RX_DAT_OVF_R
  Field DIS_RX_DAT_OVF reader - Disable UART Rx data overflow detect.
• DIS_RX_DAT_OVF_W
  Field DIS_RX_DAT_OVF writer - Disable UART Rx data overflow detect.
• ERR_WR_MASK_R
  Field ERR_WR_MASK reader - 1’h1: Receiver stops storing data into FIFO when data is wrong. 1’h0: Receiver stores the data even if the received data is wrong.
• ERR_WR_MASK_W
  Field ERR_WR_MASK writer - 1’h1: Receiver stops storing data into FIFO when data is wrong. 1’h0: Receiver stores the data even if the received data is wrong.
• IRDA_DPLX_R
  Field IRDA_DPLX reader - Set this bit to enable IrDA loopback mode.
• IRDA_DPLX_W
  Field IRDA_DPLX writer - Set this bit to enable IrDA loopback mode.
• IRDA_EN_R
  Field IRDA_EN reader - Set this bit to enable IrDA protocol.
• IRDA_EN_W
  Field IRDA_EN writer - Set this bit to enable IrDA protocol.
• IRDA_RX_INV_R
  Field IRDA_RX_INV reader - Set this bit to invert the level of IrDA receiver.
• IRDA_RX_INV_W
  Field IRDA_RX_INV writer - Set this bit to invert the level of IrDA receiver.
• IRDA_TX_EN_R
  Field IRDA_TX_EN reader - This is the start enable bit for IrDA transmitter.
• IRDA_TX_EN_W
  Field IRDA_TX_EN writer - This is the start enable bit for IrDA transmitter.
• IRDA_TX_INV_R
  Field IRDA_TX_INV reader - Set this bit to invert the level of IrDA transmitter.
• IRDA_TX_INV_W
  Field IRDA_TX_INV writer - Set this bit to invert the level of IrDA transmitter.
• IRDA_WCTL_R
  Field IRDA_WCTL reader - 1’h1: The IrDA transmitter’s 11th bit is the same as 10th bit. 1’h0: Set IrDA transmitter’s 11th bit to 0.
• IRDA_WCTL_W
  Field IRDA_WCTL writer - 1’h1: The IrDA transmitter’s 11th bit is the same as 10th bit. 1’h0: Set IrDA transmitter’s 11th bit to 0.
• LOOPBACK_R
  Field LOOPBACK reader - Set this bit to enable uart loopback test mode.
• LOOPBACK_W
  Field LOOPBACK writer - Set this bit to enable uart loopback test mode.
• MEM_CLK_EN_R
  Field MEM_CLK_EN reader - UART memory clock gate enable signal.
• MEM_CLK_EN_W
  Field MEM_CLK_EN writer - UART memory clock gate enable signal.
• PARITY_EN_R
  Field PARITY_EN reader - Set this bit to enable uart parity check.
• PARITY_EN_W
  Field PARITY_EN writer - Set this bit to enable uart parity check.
• PARITY_R
  Field PARITY reader - This register is used to configure the parity check mode.
• PARITY_W
  Field PARITY writer - This register is used to configure the parity check mode.
• R
  Register CONF0 reader
• RXD_INV_R
  Field RXD_INV reader - Set this bit to inverse the level value of uart rxd signal.
• RXD_INV_W
  Field RXD_INV writer - Set this bit to inverse the level value of uart rxd signal.
• RXFIFO_RST_R
  Field RXFIFO_RST reader - Set this bit to reset the uart receive-FIFO.
• RXFIFO_RST_W
  Field RXFIFO_RST writer - Set this bit to reset the uart receive-FIFO.
• STOP_BIT_NUM_R
  Field STOP_BIT_NUM reader - This register is used to set the length of stop bit.
• STOP_BIT_NUM_W
  Field STOP_BIT_NUM writer - This register is used to set the length of stop bit.
• SW_RTS_R
  Field SW_RTS reader - This register is used to configure the software rts signal which is used in software flow control.
• SW_RTS_W
  Field SW_RTS writer - This register is used to configure the software rts signal which is used in software flow control.
• TXD_BRK_R
  Field TXD_BRK reader - Set this bit to enbale transmitter to send NULL when the process of sending data is done.
• TXD_BRK_W
  Field TXD_BRK writer - Set this bit to enbale transmitter to send NULL when the process of sending data is done.
• TXD_INV_R
  Field TXD_INV reader - Set this bit to inverse the level value of uart txd signal.
• TXD_INV_W
  Field TXD_INV writer - Set this bit to inverse the level value of uart txd signal.
• TXFIFO_RST_R
  Field TXFIFO_RST reader - Set this bit to reset the uart transmit-FIFO.
• TXFIFO_RST_W
  Field TXFIFO_RST writer - Set this bit to reset the uart transmit-FIFO.
• TX_FLOW_EN_R
  Field TX_FLOW_EN reader - Set this bit to enable flow control function for transmitter.
• TX_FLOW_EN_W
  Field TX_FLOW_EN writer - Set this bit to enable flow control function for transmitter.
• W
  Register CONF0 writer