Struct esp32c6::rmt::ch_tx_conf0::W

pub struct W(_);

Register CH%s_TX_CONF0 writer

Implementations

impl W

pub fn tx_start(&mut self) -> TX_START_W<'_, 0>

Bit 0 - Set this bit to start sending data on CHANNEL%s.

pub fn mem_rd_rst(&mut self) -> MEM_RD_RST_W<'_, 1>

Bit 1 - Set this bit to reset read ram address for CHANNEL%s by accessing transmitter.

pub fn apb_mem_rst(&mut self) -> APB_MEM_RST_W<'_, 2>

Bit 2 - Set this bit to reset W/R ram address for CHANNEL%s by accessing apb fifo.

pub fn tx_conti_mode(&mut self) -> TX_CONTI_MODE_W<'_, 3>

Bit 3 - Set this bit to restart transmission from the first data to the last data in CHANNEL%s.

pub fn mem_tx_wrap_en(&mut self) -> MEM_TX_WRAP_EN_W<'_, 4>

Bit 4 - This is the channel %s enable bit for wraparound mode: it will resume sending at the start when the data to be sent is more than its memory size.

pub fn idle_out_lv(&mut self) -> IDLE_OUT_LV_W<'_, 5>

Bit 5 - This bit configures the level of output signal in CHANNEL%s when the latter is in IDLE state.

pub fn idle_out_en(&mut self) -> IDLE_OUT_EN_W<'_, 6>

Bit 6 - This is the output enable-control bit for CHANNEL%s in IDLE state.

pub fn tx_stop(&mut self) -> TX_STOP_W<'_, 7>

Bit 7 - Set this bit to stop the transmitter of CHANNEL%s sending data out.

pub fn div_cnt(&mut self) -> DIV_CNT_W<'_, 8>

Bits 8:15 - This register is used to configure the divider for clock of CHANNEL%s.

pub fn mem_size(&mut self) -> MEM_SIZE_W<'_, 16>

Bits 16:18 - This register is used to configure the maximum size of memory allocated to CHANNEL%s.

pub fn carrier_eff_en(&mut self) -> CARRIER_EFF_EN_W<'_, 20>

Bit 20 - 1: Add carrier modulation on the output signal only at the send data state for CHANNEL%s. 0: Add carrier modulation on the output signal at all state for CHANNEL%s. Only valid when RMT_CARRIER_EN_CH%s is 1.

pub fn carrier_en(&mut self) -> CARRIER_EN_W<'_, 21>

Bit 21 - This is the carrier modulation enable-control bit for CHANNEL%s. 1: Add carrier modulation in the output signal. 0: No carrier modulation in sig_out.

pub fn carrier_out_lv(&mut self) -> CARRIER_OUT_LV_W<'_, 22>

Bit 22 - This bit is used to configure the position of carrier wave for CHANNEL%s. 1’h0: add carrier wave on low level. 1’h1: add carrier wave on high level.

pub fn afifo_rst(&mut self) -> AFIFO_RST_W<'_, 23>

Bit 23 - Reserved

pub fn conf_update(&mut self) -> CONF_UPDATE_W<'_, 24>

Bit 24 - synchronization bit for CHANNEL%s

pub unsafe fn bits(&mut self, bits: u32) -> &mut Self

Writes raw bits to the register.

Methods from Deref<Target = W<CH_TX_CONF0_SPEC>>

pub unsafe fn bits(&mut self, bits: REG::Ux) -> &mut Self

Writes raw bits to the register.

Safety

Read datasheet or reference manual to find what values are allowed to pass.

Trait Implementations

impl Deref for W

type Target = W<CH_TX_CONF0_SPEC>

The resulting type after dereferencing.

fn deref(&self) -> &Self::Target

Dereferences the value.

impl DerefMut for W

fn deref_mut(&mut self) -> &mut Self::Target

Mutably dereferences the value.

impl From<W<CH_TX_CONF0_SPEC>> for W

fn from(writer: W<CH_TX_CONF0_SPEC>) -> Self

Converts to this type from the input type.