Struct esp32c3::rtc_cntl::sdio_conf::W

pub struct W(_);

Register SDIO_CONF writer

Implementations

impl W

pub fn sdio_timer_target(&mut self) -> SDIO_TIMER_TARGET_W<'_, 0>

Bits 0:7 - timer count to apply reg_sdio_dcap after sdio power on

pub fn sdio_dthdrv(&mut self) -> SDIO_DTHDRV_W<'_, 9>

Bits 9:10 - Tieh = 1 mode drive ability. Initially set to 0 to limit charge current

pub fn sdio_dcap(&mut self) -> SDIO_DCAP_W<'_, 11>

Bits 11:12 - ability to prevent LDO from overshoot

pub fn sdio_initi(&mut self) -> SDIO_INITI_W<'_, 13>

Bits 13:14 - add resistor from ldo output to ground. 0: no res

pub fn sdio_en_initi(&mut self) -> SDIO_EN_INITI_W<'_, 15>

Bit 15 - 0 to set init[1:0]=0

pub fn sdio_dcurlim(&mut self) -> SDIO_DCURLIM_W<'_, 16>

Bits 16:18 - tune current limit threshold when tieh = 0. About 800mA/(8+d)

pub fn sdio_modecurlim(&mut self) -> SDIO_MODECURLIM_W<'_, 19>

Bit 19 - select current limit mode

pub fn sdio_encurlim(&mut self) -> SDIO_ENCURLIM_W<'_, 20>

Bit 20 - enable current limit

pub fn sdio_reg_pd_en(&mut self) -> SDIO_REG_PD_EN_W<'_, 21>

Bit 21 - power down SDIO_REG in sleep. Only active when reg_sdio_force = 0

pub fn sdio_force(&mut self) -> SDIO_FORCE_W<'_, 22>

Bit 22 - 1: use SW option to control SDIO_REG

pub fn sdio_tieh(&mut self) -> SDIO_TIEH_W<'_, 23>

Bit 23 - SW option for SDIO_TIEH. Only active when reg_sdio_force = 1

pub fn drefl_sdio(&mut self) -> DREFL_SDIO_W<'_, 25>

Bits 25:26 - SW option for DREFL_SDIO. Only active when reg_sdio_force = 1

pub fn drefm_sdio(&mut self) -> DREFM_SDIO_W<'_, 27>

Bits 27:28 - SW option for DREFM_SDIO. Only active when reg_sdio_force = 1

pub fn drefh_sdio(&mut self) -> DREFH_SDIO_W<'_, 29>

Bits 29:30 - SW option for DREFH_SDIO. Only active when reg_sdio_force = 1

pub fn xpd_sdio(&mut self) -> XPD_SDIO_W<'_, 31>

Bit 31

pub unsafe fn bits(&mut self, bits: u32) -> &mut Self

Writes raw bits to the register.

Methods from Deref<Target = W<SDIO_CONF_SPEC>>

pub unsafe fn bits(&mut self, bits: REG::Ux) -> &mut Self

Writes raw bits to the register.

Trait Implementations

impl Deref for W

type Target = W<SDIO_CONF_SPEC>

The resulting type after dereferencing.

fn deref(&self) -> &Self::Target

Dereferences the value.

impl DerefMut for W

fn deref_mut(&mut self) -> &mut Self::Target

Mutably dereferences the value.

impl From<W<SDIO_CONF_SPEC>> for W

fn from(writer: W<SDIO_CONF_SPEC>) -> Self

Converts to this type from the input type.