pub type R = R<USER_SPEC>;
Expand description
Register USER
reader
Aliased Type§
struct R { /* private fields */ }
Implementations§
source§impl R
impl R
sourcepub fn doutdin(&self) -> DOUTDIN_R
pub fn doutdin(&self) -> DOUTDIN_R
Bit 0 - Set the bit to enable full duplex communication. 1: enable 0: disable. Can be configured in CONF state.
sourcepub fn qpi_mode(&self) -> QPI_MODE_R
pub fn qpi_mode(&self) -> QPI_MODE_R
Bit 3 - Both for master mode and slave mode. 1: spi controller is in QPI mode. 0: others. Can be configured in CONF state.
sourcepub fn tsck_i_edge(&self) -> TSCK_I_EDGE_R
pub fn tsck_i_edge(&self) -> TSCK_I_EDGE_R
Bit 5 - In the slave mode, this bit can be used to change the polarity of tsck. 0: tsck = spi_ck_i. 1:tsck = !spi_ck_i.
sourcepub fn cs_hold(&self) -> CS_HOLD_R
pub fn cs_hold(&self) -> CS_HOLD_R
Bit 6 - spi cs keep low when spi is in done phase. 1: enable 0: disable. Can be configured in CONF state.
sourcepub fn cs_setup(&self) -> CS_SETUP_R
pub fn cs_setup(&self) -> CS_SETUP_R
Bit 7 - spi cs is enable when spi is in prepare phase. 1: enable 0: disable. Can be configured in CONF state.
sourcepub fn rsck_i_edge(&self) -> RSCK_I_EDGE_R
pub fn rsck_i_edge(&self) -> RSCK_I_EDGE_R
Bit 8 - In the slave mode, this bit can be used to change the polarity of rsck. 0: rsck = !spi_ck_i. 1:rsck = spi_ck_i.
sourcepub fn ck_out_edge(&self) -> CK_OUT_EDGE_R
pub fn ck_out_edge(&self) -> CK_OUT_EDGE_R
Bit 9 - the bit combined with spi_mosi_delay_mode bits to set mosi signal delay mode. Can be configured in CONF state.
sourcepub fn fwrite_dual(&self) -> FWRITE_DUAL_R
pub fn fwrite_dual(&self) -> FWRITE_DUAL_R
Bit 12 - In the write operations read-data phase apply 2 signals. Can be configured in CONF state.
sourcepub fn fwrite_quad(&self) -> FWRITE_QUAD_R
pub fn fwrite_quad(&self) -> FWRITE_QUAD_R
Bit 13 - In the write operations read-data phase apply 4 signals. Can be configured in CONF state.
sourcepub fn usr_conf_nxt(&self) -> USR_CONF_NXT_R
pub fn usr_conf_nxt(&self) -> USR_CONF_NXT_R
Bit 15 - 1: Enable the DMA CONF phase of next seg-trans operation, which means seg-trans will continue. 0: The seg-trans will end after the current SPI seg-trans or this is not seg-trans mode. Can be configured in CONF state.
sourcepub fn sio(&self) -> SIO_R
pub fn sio(&self) -> SIO_R
Bit 17 - Set the bit to enable 3-line half duplex communication mosi and miso signals share the same pin. 1: enable 0: disable. Can be configured in CONF state.
sourcepub fn usr_miso_highpart(&self) -> USR_MISO_HIGHPART_R
pub fn usr_miso_highpart(&self) -> USR_MISO_HIGHPART_R
Bit 24 - read-data phase only access to high-part of the buffer spi_w8~spi_w15. 1: enable 0: disable. Can be configured in CONF state.
sourcepub fn usr_mosi_highpart(&self) -> USR_MOSI_HIGHPART_R
pub fn usr_mosi_highpart(&self) -> USR_MOSI_HIGHPART_R
Bit 25 - write-data phase only access to high-part of the buffer spi_w8~spi_w15. 1: enable 0: disable. Can be configured in CONF state.
sourcepub fn usr_dummy_idle(&self) -> USR_DUMMY_IDLE_R
pub fn usr_dummy_idle(&self) -> USR_DUMMY_IDLE_R
Bit 26 - spi clock is disable in dummy phase when the bit is enable. Can be configured in CONF state.
sourcepub fn usr_mosi(&self) -> USR_MOSI_R
pub fn usr_mosi(&self) -> USR_MOSI_R
Bit 27 - This bit enable the write-data phase of an operation. Can be configured in CONF state.
sourcepub fn usr_miso(&self) -> USR_MISO_R
pub fn usr_miso(&self) -> USR_MISO_R
Bit 28 - This bit enable the read-data phase of an operation. Can be configured in CONF state.
sourcepub fn usr_dummy(&self) -> USR_DUMMY_R
pub fn usr_dummy(&self) -> USR_DUMMY_R
Bit 29 - This bit enable the dummy phase of an operation. Can be configured in CONF state.
sourcepub fn usr_addr(&self) -> USR_ADDR_R
pub fn usr_addr(&self) -> USR_ADDR_R
Bit 30 - This bit enable the address phase of an operation. Can be configured in CONF state.
sourcepub fn usr_command(&self) -> USR_COMMAND_R
pub fn usr_command(&self) -> USR_COMMAND_R
Bit 31 - This bit enable the command phase of an operation. Can be configured in CONF state.