Struct esp32c2_hal::pac::io_mux::gpio::W

pub struct W(_);

Register GPIO%s writer

Implementations

impl W

pub fn mcu_oe(&mut self) -> BitWriterRaw<'_, u32, GPIO_SPEC, bool, BitM, 0>

Bit 0 - Output enable of the pad in sleep mode. 1: output enabled; 0: output disabled.

pub fn slp_sel(&mut self) -> BitWriterRaw<'_, u32, GPIO_SPEC, bool, BitM, 1>

Bit 1 - Sleep mode selection of this pad. Set to 1 to put the pad in pad mode.

pub fn mcu_wpd(&mut self) -> BitWriterRaw<'_, u32, GPIO_SPEC, bool, BitM, 2>

Bit 2 - Pull-down enable of the pad in sleep mode. 1: internal pull-down enabled; 0: internal pull-down disabled.

pub fn mcu_wpu(&mut self) -> BitWriterRaw<'_, u32, GPIO_SPEC, bool, BitM, 3>

Bit 3 - Pull-up enable of the pad during sleep mode. 1: internal pull-up enabled; 0: internal pull-up disabled.

pub fn mcu_ie(&mut self) -> BitWriterRaw<'_, u32, GPIO_SPEC, bool, BitM, 4>

Bit 4 - Input enable of the pad during sleep mode. 1: input enabled; 0: input disabled.

pub fn fun_wpd(&mut self) -> BitWriterRaw<'_, u32, GPIO_SPEC, bool, BitM, 7>

Bit 7 - Pull-down enable of the pad. 1: internal pull-down enabled; 0: internal pull-down disabled.

pub fn fun_wpu(&mut self) -> BitWriterRaw<'_, u32, GPIO_SPEC, bool, BitM, 8>

Bit 8 - Pull-up enable of the pad. 1: internal pull-up enabled; 0: internal pull-up disabled.

pub fn fun_ie(&mut self) -> BitWriterRaw<'_, u32, GPIO_SPEC, bool, BitM, 9>

Bit 9 - Input enable of the pad. 1: input enabled; 0: input disabled.

pub fn fun_drv(
    &mut self
) -> FieldWriterRaw<'_, u32, GPIO_SPEC, u8, u8, Unsafe, 2, 10>

Bits 10:11 - Select the drive strength of the pad. 0: ~5 mA; 1: ~10mA; 2: ~20mA; 3: ~40mA.

pub fn mcu_sel(
    &mut self
) -> FieldWriterRaw<'_, u32, GPIO_SPEC, u8, u8, Unsafe, 3, 12>

Bits 12:14 - Select IO MUX function for this signal. 0: Select Function 1; 1: Select Function 2; etc.

pub fn filter_en(&mut self) -> BitWriterRaw<'_, u32, GPIO_SPEC, bool, BitM, 15>

Bit 15 - Enable filter for pin input signals. 1: Filter enabled; 2: Filter disabled.

pub unsafe fn bits(&mut self, bits: u32) -> &mut W

Writes raw bits to the register.

Methods from Deref<Target = W<GPIO_SPEC>>

pub unsafe fn bits(&mut self, bits: <REG as RegisterSpec>::Ux) -> &mut W<REG>

Writes raw bits to the register.

Safety

Read datasheet or reference manual to find what values are allowed to pass.

Trait Implementations

impl Deref for W

type Target = W<GPIO_SPEC>

The resulting type after dereferencing.

fn deref(&self) -> &<W as Deref>::Target

Dereferences the value.

impl DerefMut for W

fn deref_mut(&mut self) -> &mut <W as Deref>::Target

Mutably dereferences the value.

impl From<W<GPIO_SPEC>> for W

fn from(writer: W<GPIO_SPEC>) -> W

Converts to this type from the input type.