Struct esp32c2_hal::pac::uart0::rs485_conf::W
pub struct W(_);
Expand description
Register RS485_CONF
writer
Implementations§
§impl W
impl W
pub fn rs485_en(
&mut self
) -> BitWriterRaw<'_, u32, RS485_CONF_SPEC, bool, BitM, 0>
pub fn rs485_en(
&mut self
) -> BitWriterRaw<'_, u32, RS485_CONF_SPEC, bool, BitM, 0>
Bit 0 - Set this bit to choose the rs485 mode.
pub fn dl0_en(
&mut self
) -> BitWriterRaw<'_, u32, RS485_CONF_SPEC, bool, BitM, 1>
pub fn dl0_en(
&mut self
) -> BitWriterRaw<'_, u32, RS485_CONF_SPEC, bool, BitM, 1>
Bit 1 - Set this bit to delay the stop bit by 1 bit.
pub fn dl1_en(
&mut self
) -> BitWriterRaw<'_, u32, RS485_CONF_SPEC, bool, BitM, 2>
pub fn dl1_en(
&mut self
) -> BitWriterRaw<'_, u32, RS485_CONF_SPEC, bool, BitM, 2>
Bit 2 - Set this bit to delay the stop bit by 1 bit.
pub fn rs485tx_rx_en(
&mut self
) -> BitWriterRaw<'_, u32, RS485_CONF_SPEC, bool, BitM, 3>
pub fn rs485tx_rx_en(
&mut self
) -> BitWriterRaw<'_, u32, RS485_CONF_SPEC, bool, BitM, 3>
Bit 3 - Set this bit to enable receiver could receive data when the transmitter is transmitting data in rs485 mode.
pub fn rs485rxby_tx_en(
&mut self
) -> BitWriterRaw<'_, u32, RS485_CONF_SPEC, bool, BitM, 4>
pub fn rs485rxby_tx_en(
&mut self
) -> BitWriterRaw<'_, u32, RS485_CONF_SPEC, bool, BitM, 4>
Bit 4 - 1’h1: enable rs485 transmitter to send data when rs485 receiver line is busy.
pub fn rs485_rx_dly_num(
&mut self
) -> BitWriterRaw<'_, u32, RS485_CONF_SPEC, bool, BitM, 5>
pub fn rs485_rx_dly_num(
&mut self
) -> BitWriterRaw<'_, u32, RS485_CONF_SPEC, bool, BitM, 5>
Bit 5 - This register is used to delay the receiver’s internal data signal.
pub fn rs485_tx_dly_num(
&mut self
) -> FieldWriterRaw<'_, u32, RS485_CONF_SPEC, u8, u8, Unsafe, 4, 6>
pub fn rs485_tx_dly_num(
&mut self
) -> FieldWriterRaw<'_, u32, RS485_CONF_SPEC, u8, u8, Unsafe, 4, 6>
Bits 6:9 - This register is used to delay the transmitter’s internal data signal.
Methods from Deref<Target = W<RS485_CONF_SPEC>>§
pub unsafe fn bits(&mut self, bits: <REG as RegisterSpec>::Ux) -> &mut W<REG>
pub unsafe fn bits(&mut self, bits: <REG as RegisterSpec>::Ux) -> &mut W<REG>
Writes raw bits to the register.
Safety
Read datasheet or reference manual to find what values are allowed to pass.
Trait Implementations§
§impl From<W<RS485_CONF_SPEC>> for W
impl From<W<RS485_CONF_SPEC>> for W
§fn from(writer: W<RS485_CONF_SPEC>) -> W
fn from(writer: W<RS485_CONF_SPEC>) -> W
Converts to this type from the input type.