Struct esp32::uhci0::int_raw::R

pub struct R(_);

Register INT_RAW reader

Implementations

impl R

pub fn rx_start_int_raw(&self) -> RX_START_INT_RAW_R

Bit 0 - when a separator char has been send it will produce uhci_rx_start_int interrupt.

pub fn tx_start_int_raw(&self) -> TX_START_INT_RAW_R

Bit 1 - when DMA detects a separator char it will produce uhci_tx_start_int interrupt.

pub fn rx_hung_int_raw(&self) -> RX_HUNG_INT_RAW_R

Bit 2 - when DMA takes a lot of time to receive a data it will produce uhci_rx_hung_int interrupt.

pub fn tx_hung_int_raw(&self) -> TX_HUNG_INT_RAW_R

Bit 3 - when DMA takes a lot of time to read a data from RAM it will produce uhci_tx_hung_int interrupt.

pub fn in_done_int_raw(&self) -> IN_DONE_INT_RAW_R

Bit 4 - when a in link descriptor has been completed it will produce uhci_in_done_int interrupt.

pub fn in_suc_eof_int_raw(&self) -> IN_SUC_EOF_INT_RAW_R

Bit 5 - when a data packet has been received it will produce uhci_in_suc_eof_int interrupt.

pub fn in_err_eof_int_raw(&self) -> IN_ERR_EOF_INT_RAW_R

Bit 6 - when there are some errors about eof in in link descriptor it will produce uhci_in_err_eof_int interrupt.

pub fn out_done_int_raw(&self) -> OUT_DONE_INT_RAW_R

Bit 7 - when a out link descriptor is completed it will produce uhci_out_done_int interrupt.

pub fn out_eof_int_raw(&self) -> OUT_EOF_INT_RAW_R

Bit 8 - when the current descriptor’s eof bit is 1 it will produce uhci_out_eof_int interrupt.

pub fn in_dscr_err_int_raw(&self) -> IN_DSCR_ERR_INT_RAW_R

Bit 9 - when there are some errors about the out link descriptor it will produce uhci_in_dscr_err_int interrupt.

pub fn out_dscr_err_int_raw(&self) -> OUT_DSCR_ERR_INT_RAW_R

Bit 10 - when there are some errors about the in link descriptor it will produce uhci_out_dscr_err_int interrupt.

pub fn in_dscr_empty_int_raw(&self) -> IN_DSCR_EMPTY_INT_RAW_R

Bit 11 - when there are not enough in links for DMA it will produce uhci_in_dscr_err_int interrupt.

pub fn outlink_eof_err_int_raw(&self) -> OUTLINK_EOF_ERR_INT_RAW_R

Bit 12 - when there are some errors about eof in outlink descriptor it will produce uhci_outlink_eof_err_int interrupt.

pub fn out_total_eof_int_raw(&self) -> OUT_TOTAL_EOF_INT_RAW_R

Bit 13 - When all data have been send it will produce uhci_out_total_eof_int interrupt.

pub fn send_s_q_int_raw(&self) -> SEND_S_Q_INT_RAW_R

Bit 14 - When use single send registers to send a short packets it will produce this interrupt when dma has send the short packet.

pub fn send_a_q_int_raw(&self) -> SEND_A_Q_INT_RAW_R

Bit 15 - When use always_send registers to send a series of short packets it will produce this interrupt when dma has send the short packet.

pub fn dma_infifo_full_wm_int_raw(&self) -> DMA_INFIFO_FULL_WM_INT_RAW_R

Bit 16

Methods from Deref<Target = R<INT_RAW_SPEC>>

pub fn bits(&self) -> REG::Ux

Reads raw bits from register.

Trait Implementations

impl Deref for R

type Target = R<INT_RAW_SPEC>

The resulting type after dereferencing.

fn deref(&self) -> &Self::Target

Dereferences the value.

impl From<R<INT_RAW_SPEC>> for R

fn from(reader: R<INT_RAW_SPEC>) -> Self

Converts to this type from the input type.