1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125

#[doc = "Register `MODE` reader"]
pub struct R(crate::R<MODE_SPEC>);
impl core::ops::Deref for R {
    type Target = crate::R<MODE_SPEC>;
    #[inline(always)]
    fn deref(&self) -> &Self::Target {
        &self.0
    }
}
impl From<crate::R<MODE_SPEC>> for R {
    #[inline(always)]
    fn from(reader: crate::R<MODE_SPEC>) -> Self {
        R(reader)
    }
}
#[doc = "Register `MODE` writer"]
pub struct W(crate::W<MODE_SPEC>);
impl core::ops::Deref for W {
    type Target = crate::W<MODE_SPEC>;
    #[inline(always)]
    fn deref(&self) -> &Self::Target {
        &self.0
    }
}
impl core::ops::DerefMut for W {
    #[inline(always)]
    fn deref_mut(&mut self) -> &mut Self::Target {
        &mut self.0
    }
}
impl From<crate::W<MODE_SPEC>> for W {
    #[inline(always)]
    fn from(writer: crate::W<MODE_SPEC>) -> Self {
        W(writer)
    }
}
#[doc = "Field `RESET_MODE` reader - This bit is used to configure the operating mode of the TWAI Controller. 1: Reset mode; 0: Operating mode."]
pub type RESET_MODE_R = crate::BitReader<bool>;
#[doc = "Field `RESET_MODE` writer - This bit is used to configure the operating mode of the TWAI Controller. 1: Reset mode; 0: Operating mode."]
pub type RESET_MODE_W<'a, const O: u8> = crate::BitWriter<'a, u32, MODE_SPEC, bool, O>;
#[doc = "Field `LISTEN_ONLY_MODE` reader - 1: Listen only mode. In this mode the nodes will only receive messages from the bus, without generating the acknowledge signal nor updating the RX error counter."]
pub type LISTEN_ONLY_MODE_R = crate::BitReader<bool>;
#[doc = "Field `LISTEN_ONLY_MODE` writer - 1: Listen only mode. In this mode the nodes will only receive messages from the bus, without generating the acknowledge signal nor updating the RX error counter."]
pub type LISTEN_ONLY_MODE_W<'a, const O: u8> = crate::BitWriter<'a, u32, MODE_SPEC, bool, O>;
#[doc = "Field `SELF_TEST_MODE` reader - 1: Self test mode. In this mode the TX nodes can perform a successful transmission without receiving the acknowledge signal. This mode is often used to test a single node with the self reception request command."]
pub type SELF_TEST_MODE_R = crate::BitReader<bool>;
#[doc = "Field `SELF_TEST_MODE` writer - 1: Self test mode. In this mode the TX nodes can perform a successful transmission without receiving the acknowledge signal. This mode is often used to test a single node with the self reception request command."]
pub type SELF_TEST_MODE_W<'a, const O: u8> = crate::BitWriter<'a, u32, MODE_SPEC, bool, O>;
#[doc = "Field `RX_FILTER_MODE` reader - This bit is used to configure the filter mode. 0: Dual filter mode; 1: Single filter mode."]
pub type RX_FILTER_MODE_R = crate::BitReader<bool>;
#[doc = "Field `RX_FILTER_MODE` writer - This bit is used to configure the filter mode. 0: Dual filter mode; 1: Single filter mode."]
pub type RX_FILTER_MODE_W<'a, const O: u8> = crate::BitWriter<'a, u32, MODE_SPEC, bool, O>;
impl R {
    #[doc = "Bit 0 - This bit is used to configure the operating mode of the TWAI Controller. 1: Reset mode; 0: Operating mode."]
    #[inline(always)]
    pub fn reset_mode(&self) -> RESET_MODE_R {
        RESET_MODE_R::new((self.bits & 1) != 0)
    }
    #[doc = "Bit 1 - 1: Listen only mode. In this mode the nodes will only receive messages from the bus, without generating the acknowledge signal nor updating the RX error counter."]
    #[inline(always)]
    pub fn listen_only_mode(&self) -> LISTEN_ONLY_MODE_R {
        LISTEN_ONLY_MODE_R::new(((self.bits >> 1) & 1) != 0)
    }
    #[doc = "Bit 2 - 1: Self test mode. In this mode the TX nodes can perform a successful transmission without receiving the acknowledge signal. This mode is often used to test a single node with the self reception request command."]
    #[inline(always)]
    pub fn self_test_mode(&self) -> SELF_TEST_MODE_R {
        SELF_TEST_MODE_R::new(((self.bits >> 2) & 1) != 0)
    }
    #[doc = "Bit 3 - This bit is used to configure the filter mode. 0: Dual filter mode; 1: Single filter mode."]
    #[inline(always)]
    pub fn rx_filter_mode(&self) -> RX_FILTER_MODE_R {
        RX_FILTER_MODE_R::new(((self.bits >> 3) & 1) != 0)
    }
}
impl W {
    #[doc = "Bit 0 - This bit is used to configure the operating mode of the TWAI Controller. 1: Reset mode; 0: Operating mode."]
    #[inline(always)]
    #[must_use]
    pub fn reset_mode(&mut self) -> RESET_MODE_W<0> {
        RESET_MODE_W::new(self)
    }
    #[doc = "Bit 1 - 1: Listen only mode. In this mode the nodes will only receive messages from the bus, without generating the acknowledge signal nor updating the RX error counter."]
    #[inline(always)]
    #[must_use]
    pub fn listen_only_mode(&mut self) -> LISTEN_ONLY_MODE_W<1> {
        LISTEN_ONLY_MODE_W::new(self)
    }
    #[doc = "Bit 2 - 1: Self test mode. In this mode the TX nodes can perform a successful transmission without receiving the acknowledge signal. This mode is often used to test a single node with the self reception request command."]
    #[inline(always)]
    #[must_use]
    pub fn self_test_mode(&mut self) -> SELF_TEST_MODE_W<2> {
        SELF_TEST_MODE_W::new(self)
    }
    #[doc = "Bit 3 - This bit is used to configure the filter mode. 0: Dual filter mode; 1: Single filter mode."]
    #[inline(always)]
    #[must_use]
    pub fn rx_filter_mode(&mut self) -> RX_FILTER_MODE_W<3> {
        RX_FILTER_MODE_W::new(self)
    }
    #[doc = "Writes raw bits to the register."]
    #[inline(always)]
    pub unsafe fn bits(&mut self, bits: u32) -> &mut Self {
        self.0.bits(bits);
        self
    }
}
#[doc = "Mode Register\n\nThis register you can [`read`](crate::generic::Reg::read), [`write_with_zero`](crate::generic::Reg::write_with_zero), [`reset`](crate::generic::Reg::reset), [`write`](crate::generic::Reg::write), [`modify`](crate::generic::Reg::modify). See [API](https://docs.rs/svd2rust/#read--modify--write-api).\n\nFor information about available fields see [mode](index.html) module"]
pub struct MODE_SPEC;
impl crate::RegisterSpec for MODE_SPEC {
    type Ux = u32;
}
#[doc = "`read()` method returns [mode::R](R) reader structure"]
impl crate::Readable for MODE_SPEC {
    type Reader = R;
}
#[doc = "`write(|w| ..)` method takes [mode::W](W) writer structure"]
impl crate::Writable for MODE_SPEC {
    type Writer = W;
    const ZERO_TO_MODIFY_FIELDS_BITMAP: Self::Ux = 0;
    const ONE_TO_MODIFY_FIELDS_BITMAP: Self::Ux = 0;
}
#[doc = "`reset()` method sets MODE to value 0x01"]
impl crate::Resettable for MODE_SPEC {
    const RESET_VALUE: Self::Ux = 0x01;
}