#[doc = "Register `CH%sCONF1` reader"]
pub struct R(crate::R<CHCONF1_SPEC>);
impl core::ops::Deref for R {
    type Target = crate::R<CHCONF1_SPEC>;
    #[inline(always)]
    fn deref(&self) -> &Self::Target {
        &self.0
    }
}
impl From<crate::R<CHCONF1_SPEC>> for R {
    #[inline(always)]
    fn from(reader: crate::R<CHCONF1_SPEC>) -> Self {
        R(reader)
    }
}
#[doc = "Register `CH%sCONF1` writer"]
pub struct W(crate::W<CHCONF1_SPEC>);
impl core::ops::Deref for W {
    type Target = crate::W<CHCONF1_SPEC>;
    #[inline(always)]
    fn deref(&self) -> &Self::Target {
        &self.0
    }
}
impl core::ops::DerefMut for W {
    #[inline(always)]
    fn deref_mut(&mut self) -> &mut Self::Target {
        &mut self.0
    }
}
impl From<crate::W<CHCONF1_SPEC>> for W {
    #[inline(always)]
    fn from(writer: crate::W<CHCONF1_SPEC>) -> Self {
        W(writer)
    }
}
#[doc = "Field `TX_START` reader - Set this bit to start sending data for channel0."]
pub type TX_START_R = crate::BitReader<bool>;
#[doc = "Field `TX_START` writer - Set this bit to start sending data for channel0."]
pub type TX_START_W<'a, const O: u8> = crate::BitWriter<'a, u32, CHCONF1_SPEC, bool, O>;
#[doc = "Field `RX_EN` reader - Set this bit to enbale receving data for channel0."]
pub type RX_EN_R = crate::BitReader<bool>;
#[doc = "Field `RX_EN` writer - Set this bit to enbale receving data for channel0."]
pub type RX_EN_W<'a, const O: u8> = crate::BitWriter<'a, u32, CHCONF1_SPEC, bool, O>;
#[doc = "Field `MEM_WR_RST` reader - Set this bit to reset write ram address for channel0 by receiver access."]
pub type MEM_WR_RST_R = crate::BitReader<bool>;
#[doc = "Field `MEM_WR_RST` writer - Set this bit to reset write ram address for channel0 by receiver access."]
pub type MEM_WR_RST_W<'a, const O: u8> = crate::BitWriter<'a, u32, CHCONF1_SPEC, bool, O>;
#[doc = "Field `MEM_RD_RST` reader - Set this bit to reset read ram address for channel0 by transmitter access."]
pub type MEM_RD_RST_R = crate::BitReader<bool>;
#[doc = "Field `MEM_RD_RST` writer - Set this bit to reset read ram address for channel0 by transmitter access."]
pub type MEM_RD_RST_W<'a, const O: u8> = crate::BitWriter<'a, u32, CHCONF1_SPEC, bool, O>;
#[doc = "Field `APB_MEM_RST` reader - Set this bit to reset W/R ram address for channel0 by apb fifo access"]
pub type APB_MEM_RST_R = crate::BitReader<bool>;
#[doc = "Field `APB_MEM_RST` writer - Set this bit to reset W/R ram address for channel0 by apb fifo access"]
pub type APB_MEM_RST_W<'a, const O: u8> = crate::BitWriter<'a, u32, CHCONF1_SPEC, bool, O>;
#[doc = "Field `MEM_OWNER` reader - This is the mark of channel0's ram usage right.1'b1：receiver uses the ram 0：transmitter uses the ram"]
pub type MEM_OWNER_R = crate::BitReader<bool>;
#[doc = "Field `MEM_OWNER` writer - This is the mark of channel0's ram usage right.1'b1：receiver uses the ram 0：transmitter uses the ram"]
pub type MEM_OWNER_W<'a, const O: u8> = crate::BitWriter<'a, u32, CHCONF1_SPEC, bool, O>;
#[doc = "Field `TX_CONTI_MODE` reader - Set this bit to continue sending from the first data to the last data in channel0 again and again."]
pub type TX_CONTI_MODE_R = crate::BitReader<bool>;
#[doc = "Field `TX_CONTI_MODE` writer - Set this bit to continue sending from the first data to the last data in channel0 again and again."]
pub type TX_CONTI_MODE_W<'a, const O: u8> = crate::BitWriter<'a, u32, CHCONF1_SPEC, bool, O>;
#[doc = "Field `RX_FILTER_EN` reader - This is the receive filter enable bit for channel0."]
pub type RX_FILTER_EN_R = crate::BitReader<bool>;
#[doc = "Field `RX_FILTER_EN` writer - This is the receive filter enable bit for channel0."]
pub type RX_FILTER_EN_W<'a, const O: u8> = crate::BitWriter<'a, u32, CHCONF1_SPEC, bool, O>;
#[doc = "Field `RX_FILTER_THRES` reader - in receive mode channel0 ignore input pulse when the pulse width is smaller then this value."]
pub type RX_FILTER_THRES_R = crate::FieldReader<u8, u8>;
#[doc = "Field `RX_FILTER_THRES` writer - in receive mode channel0 ignore input pulse when the pulse width is smaller then this value."]
pub type RX_FILTER_THRES_W<'a, const O: u8> =
    crate::FieldWriter<'a, u32, CHCONF1_SPEC, u8, u8, 8, O>;
#[doc = "Field `REF_CNT_RST` reader - This bit is used to reset divider in channel0."]
pub type REF_CNT_RST_R = crate::BitReader<bool>;
#[doc = "Field `REF_CNT_RST` writer - This bit is used to reset divider in channel0."]
pub type REF_CNT_RST_W<'a, const O: u8> = crate::BitWriter<'a, u32, CHCONF1_SPEC, bool, O>;
#[doc = "Field `REF_ALWAYS_ON` reader - This bit is used to select base clock. 1'b1:clk_apb 1'b0:clk_ref"]
pub type REF_ALWAYS_ON_R = crate::BitReader<bool>;
#[doc = "Field `REF_ALWAYS_ON` writer - This bit is used to select base clock. 1'b1:clk_apb 1'b0:clk_ref"]
pub type REF_ALWAYS_ON_W<'a, const O: u8> = crate::BitWriter<'a, u32, CHCONF1_SPEC, bool, O>;
#[doc = "Field `IDLE_OUT_LV` reader - This bit configures the output signal's level for channel0 in IDLE state."]
pub type IDLE_OUT_LV_R = crate::BitReader<bool>;
#[doc = "Field `IDLE_OUT_LV` writer - This bit configures the output signal's level for channel0 in IDLE state."]
pub type IDLE_OUT_LV_W<'a, const O: u8> = crate::BitWriter<'a, u32, CHCONF1_SPEC, bool, O>;
#[doc = "Field `IDLE_OUT_EN` reader - This is the output enable control bit for channel0 in IDLE state."]
pub type IDLE_OUT_EN_R = crate::BitReader<bool>;
#[doc = "Field `IDLE_OUT_EN` writer - This is the output enable control bit for channel0 in IDLE state."]
pub type IDLE_OUT_EN_W<'a, const O: u8> = crate::BitWriter<'a, u32, CHCONF1_SPEC, bool, O>;
impl R {
    #[doc = "Bit 0 - Set this bit to start sending data for channel0."]
    #[inline(always)]
    pub fn tx_start(&self) -> TX_START_R {
        TX_START_R::new((self.bits & 1) != 0)
    }
    #[doc = "Bit 1 - Set this bit to enbale receving data for channel0."]
    #[inline(always)]
    pub fn rx_en(&self) -> RX_EN_R {
        RX_EN_R::new(((self.bits >> 1) & 1) != 0)
    }
    #[doc = "Bit 2 - Set this bit to reset write ram address for channel0 by receiver access."]
    #[inline(always)]
    pub fn mem_wr_rst(&self) -> MEM_WR_RST_R {
        MEM_WR_RST_R::new(((self.bits >> 2) & 1) != 0)
    }
    #[doc = "Bit 3 - Set this bit to reset read ram address for channel0 by transmitter access."]
    #[inline(always)]
    pub fn mem_rd_rst(&self) -> MEM_RD_RST_R {
        MEM_RD_RST_R::new(((self.bits >> 3) & 1) != 0)
    }
    #[doc = "Bit 4 - Set this bit to reset W/R ram address for channel0 by apb fifo access"]
    #[inline(always)]
    pub fn apb_mem_rst(&self) -> APB_MEM_RST_R {
        APB_MEM_RST_R::new(((self.bits >> 4) & 1) != 0)
    }
    #[doc = "Bit 5 - This is the mark of channel0's ram usage right.1'b1：receiver uses the ram 0：transmitter uses the ram"]
    #[inline(always)]
    pub fn mem_owner(&self) -> MEM_OWNER_R {
        MEM_OWNER_R::new(((self.bits >> 5) & 1) != 0)
    }
    #[doc = "Bit 6 - Set this bit to continue sending from the first data to the last data in channel0 again and again."]
    #[inline(always)]
    pub fn tx_conti_mode(&self) -> TX_CONTI_MODE_R {
        TX_CONTI_MODE_R::new(((self.bits >> 6) & 1) != 0)
    }
    #[doc = "Bit 7 - This is the receive filter enable bit for channel0."]
    #[inline(always)]
    pub fn rx_filter_en(&self) -> RX_FILTER_EN_R {
        RX_FILTER_EN_R::new(((self.bits >> 7) & 1) != 0)
    }
    #[doc = "Bits 8:15 - in receive mode channel0 ignore input pulse when the pulse width is smaller then this value."]
    #[inline(always)]
    pub fn rx_filter_thres(&self) -> RX_FILTER_THRES_R {
        RX_FILTER_THRES_R::new(((self.bits >> 8) & 0xff) as u8)
    }
    #[doc = "Bit 16 - This bit is used to reset divider in channel0."]
    #[inline(always)]
    pub fn ref_cnt_rst(&self) -> REF_CNT_RST_R {
        REF_CNT_RST_R::new(((self.bits >> 16) & 1) != 0)
    }
    #[doc = "Bit 17 - This bit is used to select base clock. 1'b1:clk_apb 1'b0:clk_ref"]
    #[inline(always)]
    pub fn ref_always_on(&self) -> REF_ALWAYS_ON_R {
        REF_ALWAYS_ON_R::new(((self.bits >> 17) & 1) != 0)
    }
    #[doc = "Bit 18 - This bit configures the output signal's level for channel0 in IDLE state."]
    #[inline(always)]
    pub fn idle_out_lv(&self) -> IDLE_OUT_LV_R {
        IDLE_OUT_LV_R::new(((self.bits >> 18) & 1) != 0)
    }
    #[doc = "Bit 19 - This is the output enable control bit for channel0 in IDLE state."]
    #[inline(always)]
    pub fn idle_out_en(&self) -> IDLE_OUT_EN_R {
        IDLE_OUT_EN_R::new(((self.bits >> 19) & 1) != 0)
    }
}
impl W {
    #[doc = "Bit 0 - Set this bit to start sending data for channel0."]
    #[inline(always)]
    #[must_use]
    pub fn tx_start(&mut self) -> TX_START_W<0> {
        TX_START_W::new(self)
    }
    #[doc = "Bit 1 - Set this bit to enbale receving data for channel0."]
    #[inline(always)]
    #[must_use]
    pub fn rx_en(&mut self) -> RX_EN_W<1> {
        RX_EN_W::new(self)
    }
    #[doc = "Bit 2 - Set this bit to reset write ram address for channel0 by receiver access."]
    #[inline(always)]
    #[must_use]
    pub fn mem_wr_rst(&mut self) -> MEM_WR_RST_W<2> {
        MEM_WR_RST_W::new(self)
    }
    #[doc = "Bit 3 - Set this bit to reset read ram address for channel0 by transmitter access."]
    #[inline(always)]
    #[must_use]
    pub fn mem_rd_rst(&mut self) -> MEM_RD_RST_W<3> {
        MEM_RD_RST_W::new(self)
    }
    #[doc = "Bit 4 - Set this bit to reset W/R ram address for channel0 by apb fifo access"]
    #[inline(always)]
    #[must_use]
    pub fn apb_mem_rst(&mut self) -> APB_MEM_RST_W<4> {
        APB_MEM_RST_W::new(self)
    }
    #[doc = "Bit 5 - This is the mark of channel0's ram usage right.1'b1：receiver uses the ram 0：transmitter uses the ram"]
    #[inline(always)]
    #[must_use]
    pub fn mem_owner(&mut self) -> MEM_OWNER_W<5> {
        MEM_OWNER_W::new(self)
    }
    #[doc = "Bit 6 - Set this bit to continue sending from the first data to the last data in channel0 again and again."]
    #[inline(always)]
    #[must_use]
    pub fn tx_conti_mode(&mut self) -> TX_CONTI_MODE_W<6> {
        TX_CONTI_MODE_W::new(self)
    }
    #[doc = "Bit 7 - This is the receive filter enable bit for channel0."]
    #[inline(always)]
    #[must_use]
    pub fn rx_filter_en(&mut self) -> RX_FILTER_EN_W<7> {
        RX_FILTER_EN_W::new(self)
    }
    #[doc = "Bits 8:15 - in receive mode channel0 ignore input pulse when the pulse width is smaller then this value."]
    #[inline(always)]
    #[must_use]
    pub fn rx_filter_thres(&mut self) -> RX_FILTER_THRES_W<8> {
        RX_FILTER_THRES_W::new(self)
    }
    #[doc = "Bit 16 - This bit is used to reset divider in channel0."]
    #[inline(always)]
    #[must_use]
    pub fn ref_cnt_rst(&mut self) -> REF_CNT_RST_W<16> {
        REF_CNT_RST_W::new(self)
    }
    #[doc = "Bit 17 - This bit is used to select base clock. 1'b1:clk_apb 1'b0:clk_ref"]
    #[inline(always)]
    #[must_use]
    pub fn ref_always_on(&mut self) -> REF_ALWAYS_ON_W<17> {
        REF_ALWAYS_ON_W::new(self)
    }
    #[doc = "Bit 18 - This bit configures the output signal's level for channel0 in IDLE state."]
    #[inline(always)]
    #[must_use]
    pub fn idle_out_lv(&mut self) -> IDLE_OUT_LV_W<18> {
        IDLE_OUT_LV_W::new(self)
    }
    #[doc = "Bit 19 - This is the output enable control bit for channel0 in IDLE state."]
    #[inline(always)]
    #[must_use]
    pub fn idle_out_en(&mut self) -> IDLE_OUT_EN_W<19> {
        IDLE_OUT_EN_W::new(self)
    }
    #[doc = "Writes raw bits to the register."]
    #[inline(always)]
    pub unsafe fn bits(&mut self, bits: u32) -> &mut Self {
        self.0.bits(bits);
        self
    }
}
#[doc = "\n\nThis register you can [`read`](crate::generic::Reg::read), [`write_with_zero`](crate::generic::Reg::write_with_zero), [`reset`](crate::generic::Reg::reset), [`write`](crate::generic::Reg::write), [`modify`](crate::generic::Reg::modify). See [API](https://docs.rs/svd2rust/#read--modify--write-api).\n\nFor information about available fields see [chconf1](index.html) module"]
pub struct CHCONF1_SPEC;
impl crate::RegisterSpec for CHCONF1_SPEC {
    type Ux = u32;
}
#[doc = "`read()` method returns [chconf1::R](R) reader structure"]
impl crate::Readable for CHCONF1_SPEC {
    type Reader = R;
}
#[doc = "`write(|w| ..)` method takes [chconf1::W](W) writer structure"]
impl crate::Writable for CHCONF1_SPEC {
    type Writer = W;
    const ZERO_TO_MODIFY_FIELDS_BITMAP: Self::Ux = 0;
    const ONE_TO_MODIFY_FIELDS_BITMAP: Self::Ux = 0;
}
#[doc = "`reset()` method sets CH%sCONF1 to value 0x0f20"]
impl crate::Resettable for CHCONF1_SPEC {
    const RESET_VALUE: Self::Ux = 0x0f20;
}