Struct esp32_hal::pac::uart0::conf0::R

pub struct R(_);

Register CONF0 reader

Implementations

impl R

pub fn parity(&self) -> BitReaderRaw<bool>

Bit 0 - This register is used to configure the parity check mode. 0:even 1:odd

pub fn parity_en(&self) -> BitReaderRaw<bool>

Bit 1 - Set this bit to enable uart parity check.

pub fn bit_num(&self) -> FieldReaderRaw<u8, u8>

Bits 2:3 - This registe is used to set the length of data: 0:5bits 1:6bits 2:7bits 3:8bits

pub fn stop_bit_num(&self) -> FieldReaderRaw<u8, u8>

Bits 4:5 - This register is used to set the length of stop bit. 1:1bit 2:1.5bits 3:2bits

pub fn sw_rts(&self) -> BitReaderRaw<bool>

Bit 6 - This register is used to configure the software rts signal which is used in software flow control.

pub fn sw_dtr(&self) -> BitReaderRaw<bool>

Bit 7 - This register is used to configure the software dtr signal which is used in software flow control..

pub fn txd_brk(&self) -> BitReaderRaw<bool>

Bit 8 - Set this bit to enbale transmitter to send 0 when the process of sending data is done.

pub fn irda_dplx(&self) -> BitReaderRaw<bool>

Bit 9 - Set this bit to enable irda loopback mode.

pub fn irda_tx_en(&self) -> BitReaderRaw<bool>

Bit 10 - This is the start enable bit for irda transmitter.

pub fn irda_wctl(&self) -> BitReaderRaw<bool>

Bit 11 - 1.the irda transmitter’s 11th bit is the same to the 10th bit. 0.set irda transmitter’s 11th bit to 0.

pub fn irda_tx_inv(&self) -> BitReaderRaw<bool>

Bit 12 - Set this bit to inverse the level value of irda transmitter’s level.

pub fn irda_rx_inv(&self) -> BitReaderRaw<bool>

Bit 13 - Set this bit to inverse the level value of irda receiver’s level.

pub fn loopback(&self) -> BitReaderRaw<bool>

Bit 14 - Set this bit to enable uart loopback test mode.

pub fn tx_flow_en(&self) -> BitReaderRaw<bool>

Bit 15 - Set this bit to enable transmitter’s flow control function.

pub fn irda_en(&self) -> BitReaderRaw<bool>

Bit 16 - Set this bit to enable irda protocol.

pub fn rxfifo_rst(&self) -> BitReaderRaw<bool>

Bit 17 - Set this bit to reset uart receiver’s fifo.

pub fn txfifo_rst(&self) -> BitReaderRaw<bool>

Bit 18 - Set this bit to reset uart transmitter’s fifo.

pub fn rxd_inv(&self) -> BitReaderRaw<bool>

Bit 19 - Set this bit to inverse the level value of uart rxd signal.

pub fn cts_inv(&self) -> BitReaderRaw<bool>

Bit 20 - Set this bit to inverse the level value of uart cts signal.

pub fn dsr_inv(&self) -> BitReaderRaw<bool>

Bit 21 - Set this bit to inverse the level value of uart dsr signal.

pub fn txd_inv(&self) -> BitReaderRaw<bool>

Bit 22 - Set this bit to inverse the level value of uart txd signal.

pub fn rts_inv(&self) -> BitReaderRaw<bool>

Bit 23 - Set this bit to inverse the level value of uart rts signal.

pub fn dtr_inv(&self) -> BitReaderRaw<bool>

Bit 24 - Set this bit to inverse the level value of uart dtr signal.

pub fn clk_en(&self) -> BitReaderRaw<bool>

Bit 25 - 1.force clock on for registers.support clock only when write registers

pub fn err_wr_mask(&self) -> BitReaderRaw<bool>

Bit 26 - 1.receiver stops storing data int fifo when data is wrong. 0.receiver stores the data even if the received data is wrong.

pub fn tick_ref_always_on(&self) -> BitReaderRaw<bool>

Bit 27 - This register is used to select the clock.1.apb clock 0:ref_tick

Methods from Deref<Target = R<CONF0_SPEC>>

pub fn bits(&self) -> <REG as RegisterSpec>::Ux

Reads raw bits from register.

Trait Implementations

impl Deref for R

type Target = R<CONF0_SPEC>

The resulting type after dereferencing.

fn deref(&self) -> &<R as Deref>::Target

Dereferences the value.

impl From<R<CONF0_SPEC>> for R

fn from(reader: R<CONF0_SPEC>) -> R

Converts to this type from the input type.