ws63-hal 0.2.1

Hardware Abstraction Layer for HiSilicon WS63 (RISC-V RV32IMFC_Zicsr)
Documentation 
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155

//! Ultra-Low-Power GPIO (ULP_GPIO) driver for WS63.
//!
//! The WS63 ULP_GPIO provides 8 additional GPIO pins (GPIO107-114) that
//! can operate in ultra-low-power modes. The register layout is identical
//! to the standard GPIO blocks.
//!
//! These pins are accessible at physical address 0x5703_0000 and use
//! the same register layout as GPIO0.

use crate::peripherals::UlpGpio;
use core::marker::PhantomData;

/// ULP GPIO pin mode marker types.
pub struct Input;
pub struct Output;

/// ULP GPIO pin driver.
pub struct UlpGpioPin<'d, MODE> {
    bit: u8,
    _mode: PhantomData<&'d MODE>,
}

fn regs() -> &'static ws63_pac::gpio0::RegisterBlock {
    // SAFETY: PAC peripheral pointer is a static physical MMIO address, always valid
    unsafe { &*UlpGpio::ptr() }
}

impl<MODE> UlpGpioPin<'_, MODE> {
    /// Get the pin number (107-114).
    pub fn number(&self) -> u8 {
        107 + self.bit
    }
}

impl UlpGpioPin<'_, Output> {
    /// Set the pin high.
    pub fn set_high(&mut self) {
        unsafe { regs().gpio_data_set().write(|w| w.bits(1 << self.bit)) };
    }

    /// Set the pin low.
    pub fn set_low(&mut self) {
        unsafe { regs().gpio_data_clr().write(|w| w.bits(1 << self.bit)) };
    }

    /// Toggle the pin output level.
    pub fn toggle(&mut self) {
        let val = regs().gpio_sw_out().read().bits();
        if val & (1 << self.bit) != 0 {
            unsafe { regs().gpio_data_clr().write(|w| w.bits(1 << self.bit)) };
        } else {
            unsafe { regs().gpio_data_set().write(|w| w.bits(1 << self.bit)) };
        }
    }

    /// Check if the output is set high.
    pub fn is_set_high(&self) -> bool {
        (regs().gpio_sw_out().read().bits() >> self.bit) & 1 != 0
    }

    /// Convert the pin to input mode.
    pub fn into_input(self) -> UlpGpioPin<'static, Input> {
        regs().gpio_sw_oen().modify(|r, w| unsafe { w.bits(r.bits() | (1 << self.bit)) });
        UlpGpioPin { bit: self.bit, _mode: PhantomData }
    }
}

impl UlpGpioPin<'_, Input> {
    /// Check if the input is high.
    pub fn is_high(&self) -> bool {
        (regs().gpio_sw_out().read().bits() >> self.bit) & 1 != 0
    }

    /// Check if the input is low.
    pub fn is_low(&self) -> bool {
        !self.is_high()
    }

    /// Enable the interrupt for this pin.
    pub fn enable_interrupt(&self) {
        regs().gpio_int_en().modify(|r, w| unsafe { w.bits(r.bits() | (1 << self.bit)) });
    }

    /// Disable the interrupt for this pin.
    pub fn disable_interrupt(&self) {
        regs().gpio_int_en().modify(|r, w| unsafe { w.bits(r.bits() & !(1 << self.bit)) });
    }

    /// Clear the interrupt for this pin.
    pub fn clear_interrupt(&self) {
        unsafe { regs().gpio_int_eoi().write(|w| w.bits(1 << self.bit)) };
    }

    /// Check if an interrupt is pending for this pin.
    pub fn interrupt_pending(&self) -> bool {
        (regs().gpio_int_raw().read().bits() >> self.bit) & 1 != 0
    }

    /// Convert the pin to output mode.
    pub fn into_output(self) -> UlpGpioPin<'static, Output> {
        regs().gpio_sw_oen().modify(|r, w| unsafe { w.bits(r.bits() & !(1 << self.bit)) });
        UlpGpioPin { bit: self.bit, _mode: PhantomData }
    }
}

// ── embedded-hal traits ────────────────────────────────────────────

impl embedded_hal::digital::ErrorType for UlpGpioPin<'_, Output> {
    type Error = core::convert::Infallible;
}
impl embedded_hal::digital::OutputPin for UlpGpioPin<'_, Output> {
    fn set_low(&mut self) -> Result<(), Self::Error> {
        UlpGpioPin::set_low(self);
        Ok(())
    }
    fn set_high(&mut self) -> Result<(), Self::Error> {
        UlpGpioPin::set_high(self);
        Ok(())
    }
}
impl embedded_hal::digital::StatefulOutputPin for UlpGpioPin<'_, Output> {
    fn is_set_high(&mut self) -> Result<bool, Self::Error> {
        Ok(UlpGpioPin::is_set_high(self))
    }
    fn is_set_low(&mut self) -> Result<bool, Self::Error> {
        Ok(!UlpGpioPin::is_set_high(self))
    }
}
impl embedded_hal::digital::ErrorType for UlpGpioPin<'_, Input> {
    type Error = core::convert::Infallible;
}
impl embedded_hal::digital::InputPin for UlpGpioPin<'_, Input> {
    fn is_high(&mut self) -> Result<bool, Self::Error> {
        Ok(UlpGpioPin::is_high(self))
    }
    fn is_low(&mut self) -> Result<bool, Self::Error> {
        Ok(!UlpGpioPin::is_high(self))
    }
}

/// Create a ULP GPIO pin in input mode.
pub fn create_input_pin(pin: u8) -> UlpGpioPin<'static, Input> {
    let bit = pin - 107;
    assert!(bit < 8, "ULP GPIO pin must be 107-114");
    regs().gpio_sw_oen().modify(|r, w| unsafe { w.bits(r.bits() | (1 << bit)) });
    UlpGpioPin { bit, _mode: PhantomData }
}

/// Create a ULP GPIO pin in output mode.
pub fn create_output_pin(pin: u8) -> UlpGpioPin<'static, Output> {
    let bit = pin - 107;
    assert!(bit < 8, "ULP GPIO pin must be 107-114");
    regs().gpio_sw_oen().modify(|r, w| unsafe { w.bits(r.bits() & !(1 << bit)) });
    UlpGpioPin { bit, _mode: PhantomData }
}