stm32h7 0.16.0

Device support crates for STM32H7 devices
Documentation 
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63

///Register `CSR1` reader
pub type R = crate::R<CSR1rs>;
///Field `PVDO` reader - Programmable voltage detect output This bit is set and cleared by hardware. It is valid only if the PVD has been enabled by the PVDE bit. Note: since the PVD is disabled in Standby mode, this bit is equal to 0 after Standby or reset until the PVDE bit is set.
pub type PVDO_R = crate::BitReader;
///Field `ACTVOSRDY` reader - Voltage levels ready bit for currently used VOS and SDLEVEL This bit is set to 1 by hardware when the voltage regulator and the SD converter are both disabled and Bypass mode is selected in PWR control register 3 (PWR_CR3).
pub type ACTVOSRDY_R = crate::BitReader;
///Field `ACTVOS` reader - VOS currently applied for VCORE voltage scaling selection. These bits reflect the last VOS value applied to the PMU.
pub type ACTVOS_R = crate::FieldReader;
///Field `AVDO` reader - Analog voltage detector output on VDDA This bit is set and cleared by hardware. It is valid only if AVD on VDDA is enabled by the AVDEN bit. Note: Since the AVD is disabled in Standby mode, this bit is equal to 0 after Standby or reset until the AVDEN bit is set.
pub type AVDO_R = crate::BitReader;
///Field `MMCVDO` reader - MMCVDO
pub type MMCVDO_R = crate::BitReader;
impl R {
    ///Bit 4 - Programmable voltage detect output This bit is set and cleared by hardware. It is valid only if the PVD has been enabled by the PVDE bit. Note: since the PVD is disabled in Standby mode, this bit is equal to 0 after Standby or reset until the PVDE bit is set.
    #[inline(always)]
    pub fn pvdo(&self) -> PVDO_R {
        PVDO_R::new(((self.bits >> 4) & 1) != 0)
    }
    ///Bit 13 - Voltage levels ready bit for currently used VOS and SDLEVEL This bit is set to 1 by hardware when the voltage regulator and the SD converter are both disabled and Bypass mode is selected in PWR control register 3 (PWR_CR3).
    #[inline(always)]
    pub fn actvosrdy(&self) -> ACTVOSRDY_R {
        ACTVOSRDY_R::new(((self.bits >> 13) & 1) != 0)
    }
    ///Bits 14:15 - VOS currently applied for VCORE voltage scaling selection. These bits reflect the last VOS value applied to the PMU.
    #[inline(always)]
    pub fn actvos(&self) -> ACTVOS_R {
        ACTVOS_R::new(((self.bits >> 14) & 3) as u8)
    }
    ///Bit 16 - Analog voltage detector output on VDDA This bit is set and cleared by hardware. It is valid only if AVD on VDDA is enabled by the AVDEN bit. Note: Since the AVD is disabled in Standby mode, this bit is equal to 0 after Standby or reset until the AVDEN bit is set.
    #[inline(always)]
    pub fn avdo(&self) -> AVDO_R {
        AVDO_R::new(((self.bits >> 16) & 1) != 0)
    }
    ///Bit 17 - MMCVDO
    #[inline(always)]
    pub fn mmcvdo(&self) -> MMCVDO_R {
        MMCVDO_R::new(((self.bits >> 17) & 1) != 0)
    }
}
impl core::fmt::Debug for R {
    fn fmt(&self, f: &mut core::fmt::Formatter) -> core::fmt::Result {
        f.debug_struct("CSR1")
            .field("pvdo", &self.pvdo())
            .field("actvosrdy", &self.actvosrdy())
            .field("actvos", &self.actvos())
            .field("avdo", &self.avdo())
            .field("mmcvdo", &self.mmcvdo())
            .finish()
    }
}
/**PWR control status register 1

You can [`read`](crate::Reg::read) this register and get [`csr1::R`](R). See [API](https://docs.rs/svd2rust/#read--modify--write-api).*/
pub struct CSR1rs;
impl crate::RegisterSpec for CSR1rs {
    type Ux = u32;
}
///`read()` method returns [`csr1::R`](R) reader structure
impl crate::Readable for CSR1rs {}
///`reset()` method sets CSR1 to value 0x4000
impl crate::Resettable for CSR1rs {
    const RESET_VALUE: u32 = 0x4000;
}