SSD1331 driver

SPI (4 wire) driver for the SSD1331 OLED display.

The display is configured by this driver to use a 16 bit, R5 G6 B5 pixel definition. You can convert images into the correct BMP format with the following commands:

convert my_image.png -flip -type truecolor -define bmp:subtype=RGB565 -depth 16 -strip my_image.bmp

You can also export images directly from The GIMP by saving as .bmp and choosing the following option:

Documentation

Examples

Load a BMP image of the Rust logo and display it in the center of the display. From examples/bmp.rs:

#![no_std]
#![no_main]

use cortex_m_rt::{entry, exception, ExceptionFrame};
use embedded_graphics::{geometry::Point, image::Image, pixelcolor::Rgb565, prelude::*};
use panic_semihosting as _;
use ssd1331::{DisplayRotation, Ssd1331};
use stm32f1xx_hal::{
    delay::Delay,
    prelude::*,
    spi::{Mode, Phase, Polarity, Spi},
    stm32,
};
use tinybmp::Bmp;

#[entry]
fn main() -> ! {
    let cp = cortex_m::Peripherals::take().unwrap();
    let dp = stm32::Peripherals::take().unwrap();
    let mut flash = dp.FLASH.constrain();
    let mut rcc = dp.RCC.constrain();
    let clocks = rcc.cfgr.freeze(&mut flash.acr);
    let mut afio = dp.AFIO.constrain(&mut rcc.apb2);
    let mut gpioa = dp.GPIOA.split(&mut rcc.apb2);
    let mut gpiob = dp.GPIOB.split(&mut rcc.apb2);

    // SPI1
    let sck = gpioa.pa5.into_alternate_push_pull(&mut gpioa.crl);
    let miso = gpioa.pa6;
    let mosi = gpioa.pa7.into_alternate_push_pull(&mut gpioa.crl);
    let mut delay = Delay::new(cp.SYST, clocks);
    let mut rst = gpiob.pb0.into_push_pull_output(&mut gpiob.crl);
    let dc = gpiob.pb1.into_push_pull_output(&mut gpiob.crl);

    let spi = Spi::spi1(
        dp.SPI1,
        (sck, miso, mosi),
        &mut afio.mapr,
        Mode {
            polarity: Polarity::IdleLow,
            phase: Phase::CaptureOnFirstTransition,
        },
        8.mhz(),
        clocks,
        &mut rcc.apb2,
    );

    let mut disp = Ssd1331::new(spi, dc, DisplayRotation::Rotate0);

    disp.reset(&mut rst, &mut delay).unwrap();
    disp.init().unwrap();
    disp.flush().unwrap();

    let (w, h) = disp.dimensions();

    let bmp = Bmp::from_slice(include_bytes!("./rust-pride.bmp")).unwrap();

    let im: Image<Bmp, Rgb565> = Image::new(&bmp, Point::zero());

    // Position image in the center of the display
    let moved = im.translate(Point::new(
        (w as u32 - bmp.width()) as i32 / 2,
        (h as u32 - bmp.height()) as i32 / 2,
    ));

    moved.draw(&mut disp).unwrap();

    disp.flush().unwrap();

    loop {}
}

#[exception]
fn HardFault(ef: &ExceptionFrame) -> ! {
    panic!("{:#?}", ef);
}

Migrating from 0.1 to 0.2

The full changelog can be found here. A tl;dr version is shown below.

Version 0.1.x

use ssd1331::{prelude::*, Builder};

let mut disp: GraphicsMode<_> = Builder::new().connect_spi(spi, dc).into();

disp.reset(&mut rst, &mut delay);
disp.init().unwrap();
disp.flush().unwrap();

disp.get_dimensions();
disp.get_rotation();

Version 0.2.x

use ssd1331::{Ssd1331, DisplayRotation};

let mut disp = Ssd1331::new(spi, dc, DisplayRotation::Rotate0);

disp.reset(&mut rst, &mut delay).unwrap();
disp.init().unwrap();
disp.flush().unwrap();

disp.dimensions();
disp.rotation();

License

Licensed under either of

• Apache License, Version 2.0 (LICENSE-APACHE or http://www.apache.org/licenses/LICENSE-2.0)
• MIT license (LICENSE-MIT or http://opensource.org/licenses/MIT)

at your option.

Contribution

Unless you explicitly state otherwise, any contribution intentionally submitted for inclusion in the work by you, as defined in the Apache-2.0 license, shall be dual licensed as above, without any additional terms or conditions.