[−][src]Struct nrf52832_hal::target::pwm0::RegisterBlock
Register block
Fields
tasks_stop: TASKS_STOP
0x04 - Stops PWM pulse generation on all channels at the end of current PWM period, and stops sequence playback
tasks_seqstart: [TASKS_SEQSTART; 2]
0x08 - Description collection[0]: Loads the first PWM value on all enabled channels from sequence 0, and starts playing that sequence at the rate defined in SEQ[0]REFRESH and/or DECODER.MODE. Causes PWM generation to start it was not running.
tasks_nextstep: TASKS_NEXTSTEP
0x10 - Steps by one value in the current sequence on all enabled channels if DECODER.MODE=NextStep. Does not cause PWM generation to start it was not running.
events_stopped: EVENTS_STOPPED
0x104 - Response to STOP task, emitted when PWM pulses are no longer generated
events_seqstarted: [EVENTS_SEQSTARTED; 2]
0x108 - Description collection[0]: First PWM period started on sequence 0
events_seqend: [EVENTS_SEQEND; 2]
0x110 - Description collection[0]: Emitted at end of every sequence 0, when last value from RAM has been applied to wave counter
events_pwmperiodend: EVENTS_PWMPERIODEND
0x118 - Emitted at the end of each PWM period
events_loopsdone: EVENTS_LOOPSDONE
0x11c - Concatenated sequences have been played the amount of times defined in LOOP.CNT
shorts: SHORTS
0x200 - Shortcut register
inten: INTEN
0x300 - Enable or disable interrupt
intenset: INTENSET
0x304 - Enable interrupt
intenclr: INTENCLR
0x308 - Disable interrupt
enable: ENABLE
0x500 - PWM module enable register
mode: MODE
0x504 - Selects operating mode of the wave counter
countertop: COUNTERTOP
0x508 - Value up to which the pulse generator counter counts
prescaler: PRESCALER
0x50c - Configuration for PWM_CLK
decoder: DECODER
0x510 - Configuration of the decoder
loop_: LOOP
0x514 - Amount of playback of a loop
seq0: SEQ
0x520 - Unspecified
seq1: SEQ
0x540 - Unspecified
psel: PSEL
0x560 - Unspecified
Auto Trait Implementations
impl Send for RegisterBlock
impl Send for RegisterBlock
impl !Sync for RegisterBlock
impl !Sync for RegisterBlock
Blanket Implementations
impl<T> From for T
[src]
impl<T> From for T
impl<T, U> TryFrom for T where
T: From<U>,
[src]
impl<T, U> TryFrom for T where
T: From<U>,
type Error = !
try_from
)The type returned in the event of a conversion error.
fn try_from(value: U) -> Result<T, <T as TryFrom<U>>::Error>
[src]
fn try_from(value: U) -> Result<T, <T as TryFrom<U>>::Error>
try_from
)Performs the conversion.
impl<T, U> TryInto for T where
U: TryFrom<T>,
[src]
impl<T, U> TryInto for T where
U: TryFrom<T>,
type Error = <U as TryFrom<T>>::Error
try_from
)The type returned in the event of a conversion error.
fn try_into(self) -> Result<U, <U as TryFrom<T>>::Error>
[src]
fn try_into(self) -> Result<U, <U as TryFrom<T>>::Error>
try_from
)Performs the conversion.
impl<T, U> Into for T where
U: From<T>,
[src]
impl<T, U> Into for T where
U: From<T>,
impl<T> Borrow for T where
T: ?Sized,
[src]
impl<T> Borrow for T where
T: ?Sized,
impl<T> BorrowMut for T where
T: ?Sized,
[src]
impl<T> BorrowMut for T where
T: ?Sized,
fn borrow_mut(&mut self) -> &mut T
[src]
fn borrow_mut(&mut self) -> &mut T
Mutably borrows from an owned value. Read more
impl<T> Any for T where
T: 'static + ?Sized,
[src]
impl<T> Any for T where
T: 'static + ?Sized,
fn get_type_id(&self) -> TypeId
[src]
fn get_type_id(&self) -> TypeId
🔬 This is a nightly-only experimental API. (get_type_id
)
this method will likely be replaced by an associated static
Gets the TypeId
of self
. Read more