[−][src]Struct nrf52832_hal::nrf52832_pac::uarte0::RegisterBlock
Register block
Fields
tasks_startrx: TASKS_STARTRX
0x00 - Start UART receiver
tasks_stoprx: TASKS_STOPRX
0x04 - Stop UART receiver
tasks_starttx: TASKS_STARTTX
0x08 - Start UART transmitter
tasks_stoptx: TASKS_STOPTX
0x0c - Stop UART transmitter
tasks_flushrx: TASKS_FLUSHRX
0x2c - Flush RX FIFO into RX buffer
events_cts: EVENTS_CTS
0x100 - CTS is activated (set low). Clear To Send.
events_ncts: EVENTS_NCTS
0x104 - CTS is deactivated (set high). Not Clear To Send.
events_rxdrdy: EVENTS_RXDRDY
0x108 - Data received in RXD (but potentially not yet transferred to Data RAM)
events_endrx: EVENTS_ENDRX
0x110 - Receive buffer is filled up
events_txdrdy: EVENTS_TXDRDY
0x11c - Data sent from TXD
events_endtx: EVENTS_ENDTX
0x120 - Last TX byte transmitted
events_error: EVENTS_ERROR
0x124 - Error detected
events_rxto: EVENTS_RXTO
0x144 - Receiver timeout
events_rxstarted: EVENTS_RXSTARTED
0x14c - UART receiver has started
events_txstarted: EVENTS_TXSTARTED
0x150 - UART transmitter has started
events_txstopped: EVENTS_TXSTOPPED
0x158 - Transmitter stopped
shorts: SHORTS
0x200 - Shortcut register
inten: INTEN
0x300 - Enable or disable interrupt
intenset: INTENSET
0x304 - Enable interrupt
intenclr: INTENCLR
0x308 - Disable interrupt
errorsrc: ERRORSRC
0x480 - Error source
enable: ENABLE
0x500 - Enable UART
psel: PSEL
0x508 - Unspecified
baudrate: BAUDRATE
0x524 - Baud rate. Accuracy depends on the HFCLK source selected.
rxd: RXD
0x534 - RXD EasyDMA channel
txd: TXD
0x544 - TXD EasyDMA channel
config: CONFIG
0x56c - Configuration of parity and hardware flow control
Auto Trait Implementations
impl Send for RegisterBlock
impl Send for RegisterBlock
impl !Sync for RegisterBlock
impl !Sync for RegisterBlock
Blanket Implementations
impl<T, U> TryFrom for T where
T: From<U>,
[src]
impl<T, U> TryFrom for T where
T: From<U>,
type Error = !
try_from
)The type returned in the event of a conversion error.
fn try_from(value: U) -> Result<T, <T as TryFrom<U>>::Error>
[src]
fn try_from(value: U) -> Result<T, <T as TryFrom<U>>::Error>
try_from
)Performs the conversion.
impl<T> From for T
[src]
impl<T> From for T
impl<T, U> TryInto for T where
U: TryFrom<T>,
[src]
impl<T, U> TryInto for T where
U: TryFrom<T>,
type Error = <U as TryFrom<T>>::Error
try_from
)The type returned in the event of a conversion error.
fn try_into(self) -> Result<U, <U as TryFrom<T>>::Error>
[src]
fn try_into(self) -> Result<U, <U as TryFrom<T>>::Error>
try_from
)Performs the conversion.
impl<T, U> Into for T where
U: From<T>,
[src]
impl<T, U> Into for T where
U: From<T>,
impl<T> Borrow for T where
T: ?Sized,
[src]
impl<T> Borrow for T where
T: ?Sized,
impl<T> BorrowMut for T where
T: ?Sized,
[src]
impl<T> BorrowMut for T where
T: ?Sized,
fn borrow_mut(&mut self) -> &mut T
[src]
fn borrow_mut(&mut self) -> &mut T
Mutably borrows from an owned value. Read more
impl<T> Any for T where
T: 'static + ?Sized,
[src]
impl<T> Any for T where
T: 'static + ?Sized,
fn get_type_id(&self) -> TypeId
[src]
fn get_type_id(&self) -> TypeId
🔬 This is a nightly-only experimental API. (get_type_id
)
this method will likely be replaced by an associated static
Gets the TypeId
of self
. Read more