Struct UnitFlag 

pub struct UnitFlag(/* private fields */);

The flags of a unit’s status report.

Implementations

impl UnitFlag

pub const NONE: Self

No bits set.

pub const REBOOT_REQUIRED: Self

A changed setting takes effect after a reboot.

pub const FPGA_UPGRADE: Self

A newer video processor image is available.

pub const DHCP: Self

The IP configuration comes from DHCP.

pub const NET_PENDING: Self

The IP configuration was changed through the mesh, and is reverted unless the mesh controller confirms it in time.

pub const FAN_QUIET: Self

The fan runs in quiet mode.

pub const EXTERNAL_PSU: Self

Powered by an external supply rather than PoE.

pub const FPGA_CONFIGURED: Self

The video processor runs with its IP configured. Without it the encoder and decoder health carry nothing.

pub const ENCODER_ACTIVE: Self

The encoder is enabled.

pub const DECODER_ACTIVE: Self

The decoder is enabled.

pub const AUTO_DISABLE: Self

The decoder disables itself without a display.

pub const AUTO_DISABLE_ACTIVE: Self

The decoder disabled itself without a display.

pub const OFF_NO_SIGNAL: Self

The HDMI output switches off without a signal.

pub const OFF_NO_SIGNAL_ACTIVE: Self

The HDMI output switched off without a signal.

pub const POWER_CHECK: Self

Display power is checked before the decoder is enabled.

pub const BOOT_COUNT: Self

The boot count is reported.

pub const FAN_SPEED: Self

The fan speed is reported.

pub const LOCATE_SUPPORTED: Self

The unit takes UnitCommandKind::LOCATE.

pub const LOCATE: Self

The unit is being located: its board-ID LED flashes, and an output shows “Locate Device”.

pub const fn from_bits(bits: u32) -> Self

Wraps a raw wire value, including bits this library has no name for.

pub const fn bits(self) -> u32

Returns the raw wire value.

pub const fn has(self, other: Self) -> bool

Reports whether every bit in other is set.

pub const fn is_empty(self) -> bool

Reports whether no bit is set.

Trait Implementations

impl BitAnd for UnitFlag

type Output = UnitFlag

The resulting type after applying the & operator.

fn bitand(self, rhs: Self) -> Self

Performs the & operation.

impl BitOr for UnitFlag

type Output = UnitFlag

The resulting type after applying the | operator.

fn bitor(self, rhs: Self) -> Self

Performs the | operation.

impl BitOrAssign for UnitFlag

fn bitor_assign(&mut self, rhs: Self)

Performs the |= operation.

impl Clone for UnitFlag

fn clone(&self) -> Self

Returns a duplicate of the value.

fn clone_from(&mut self, source: &Self)

Performs copy-assignment from source.

impl Copy for UnitFlag

impl Debug for UnitFlag

fn fmt(&self, f: &mut Formatter<'_>) -> Result

Formats the value using the given formatter.

impl Default for UnitFlag

fn default() -> Self

Returns the “default value” for a type.

impl Display for UnitFlag

fn fmt(&self, f: &mut Formatter<'_>) -> Result

Formats the value using the given formatter.

impl Eq for UnitFlag

impl Hash for UnitFlag

fn hash<__H: Hasher>(&self, state: &mut __H)

Feeds this value into the given Hasher.

fn hash_slice<H>(data: &[Self], state: &mut H)

where H: Hasher, Self: Sized,

Feeds a slice of this type into the given Hasher.

impl Ord for UnitFlag

fn cmp(&self, other: &Self) -> Ordering

This method returns an Ordering between self and other.

fn max(self, other: Self) -> Self

where Self: Sized,

Compares and returns the maximum of two values.

fn min(self, other: Self) -> Self

where Self: Sized,

Compares and returns the minimum of two values.

fn clamp(self, min: Self, max: Self) -> Self

where Self: Sized,

Restrict a value to a certain interval.

fn clamp_to<R>(self, range: R) -> Self

where Self: Sized, R: ClampBounds<Self>,

🔬This is a nightly-only experimental API. (clamp_to)

Restrict a value to a certain range.

impl PartialEq for UnitFlag

fn eq(&self, other: &Self) -> bool

Equality operator ==.

fn ne(&self, other: &Rhs) -> bool

Inequality operator !=.

impl PartialOrd for UnitFlag

fn partial_cmp(&self, other: &Self) -> Option<Ordering>

This method returns an ordering between self and other values if one exists.

fn lt(&self, other: &Rhs) -> bool

Tests less than (for self and other) and is used by the < operator.

fn le(&self, other: &Rhs) -> bool

Tests less than or equal to (for self and other) and is used by the <= operator.

fn gt(&self, other: &Rhs) -> bool

Tests greater than (for self and other) and is used by the > operator.

fn ge(&self, other: &Rhs) -> bool

Tests greater than or equal to (for self and other) and is used by the >= operator.

impl StructuralPartialEq for UnitFlag