Struct DeviceFeature 

pub struct DeviceFeature(/* private fields */);

Capabilities a device reports in its hello frame.

Implementations

impl DeviceFeature

pub const NONE: Self

No bits set.

pub const IR_RX: Self

Receives infrared.

pub const IR_TX: Self

Transmits infrared.

pub const CEC: Self

Speaks CEC.

pub const V2IP_SOURCE: Self

Acts as a V2IP stream source.

pub const V2IP_SINK: Self

Acts as a V2IP stream sink.

pub const VIDEO_ROUTING: Self

Routes video.

pub const AUDIO_ROUTING: Self

Routes audio.

pub const VOLUME_CONTROL: Self

Controls volume.

pub const AUDIO_RETURN: Self

Supports audio return.

pub const REMOTE_CONTROL: Self

Passes remote-control commands through.

pub const SETUP_COMPLETED: Self

Installer setup has been completed.

pub const MESH_MASTER: Self

Is the master of its mesh.

pub const STATUS_NOTIFY: Self

Has a notification pending.

pub const STATUS_WARNING: Self

Has a warning pending.

pub const STATUS_ERROR: Self

Has an error pending.

pub const STATUS_REBOOT: Self

Is about to reboot.

pub const MESH_MEMBER: Self

Is a member of a mesh.

pub const AUDIO_AMPLIFIER: Self

Is an audio amplifier.

pub const BOOTING: Self

Is still booting.

pub const MANAGER: Self

Is a management client rather than a device.

pub const STATUS_POWER_SAVE: Self

Is in power-save mode.

pub const MESH: Self

Supports meshing.

pub const MULTIVIEWER: Self

Is a multiviewer.

pub const STATUS_CRASHED: Self

Has crashed since it last booted.

pub const VIDEO_WALL: Self

Supports video walls.

pub const CONFIG_INITIALISED: Self

Initialises the configuration it broadcasts.

Firmware without this bit sends a device configuration built over uninitialised memory, so fields it did not mean to write carry junk.

pub const BOOT_BIT: Self

Set while the device is in its boot loader.

pub const fn from_bits(bits: u32) -> Self

Wraps a raw wire value, including bits this library has no name for.

pub const fn bits(self) -> u32

Returns the raw wire value.

pub const fn has(self, other: Self) -> bool

Reports whether every bit in other is set.

pub const fn is_empty(self) -> bool

Reports whether no bit is set.

Trait Implementations

impl BitAnd for DeviceFeature

type Output = DeviceFeature

The resulting type after applying the & operator.

fn bitand(self, rhs: Self) -> Self

Performs the & operation.

impl BitOr for DeviceFeature

type Output = DeviceFeature

The resulting type after applying the | operator.

fn bitor(self, rhs: Self) -> Self

Performs the | operation.

impl BitOrAssign for DeviceFeature

fn bitor_assign(&mut self, rhs: Self)

Performs the |= operation.

impl Clone for DeviceFeature

fn clone(&self) -> DeviceFeature

Returns a duplicate of the value.

fn clone_from(&mut self, source: &Self)

Performs copy-assignment from source.

impl Copy for DeviceFeature

impl Debug for DeviceFeature

fn fmt(&self, f: &mut Formatter<'_>) -> Result

Formats the value using the given formatter.

impl Default for DeviceFeature

fn default() -> DeviceFeature

Returns the “default value” for a type.

impl Display for DeviceFeature

fn fmt(&self, f: &mut Formatter<'_>) -> Result

Formats the value using the given formatter.

impl Eq for DeviceFeature

impl Hash for DeviceFeature

fn hash<__H: Hasher>(&self, state: &mut __H)

Feeds this value into the given Hasher.

fn hash_slice<H>(data: &[Self], state: &mut H)

where H: Hasher, Self: Sized,

Feeds a slice of this type into the given Hasher.

impl Ord for DeviceFeature

fn cmp(&self, other: &DeviceFeature) -> Ordering

This method returns an Ordering between self and other.

fn max(self, other: Self) -> Self

where Self: Sized,

Compares and returns the maximum of two values.

fn min(self, other: Self) -> Self

where Self: Sized,

Compares and returns the minimum of two values.

fn clamp(self, min: Self, max: Self) -> Self

where Self: Sized,

Restrict a value to a certain interval.

fn clamp_to<R>(self, range: R) -> Self

where Self: Sized, R: ClampBounds<Self>,

🔬This is a nightly-only experimental API. (clamp_to)

Restrict a value to a certain range.

impl PartialEq for DeviceFeature

fn eq(&self, other: &DeviceFeature) -> bool

Equality operator ==.

fn ne(&self, other: &Rhs) -> bool

Inequality operator !=.

impl PartialOrd for DeviceFeature

fn partial_cmp(&self, other: &DeviceFeature) -> Option<Ordering>

This method returns an ordering between self and other values if one exists.

fn lt(&self, other: &Rhs) -> bool

Tests less than (for self and other) and is used by the < operator.

fn le(&self, other: &Rhs) -> bool

Tests less than or equal to (for self and other) and is used by the <= operator.

fn gt(&self, other: &Rhs) -> bool

Tests greater than (for self and other) and is used by the > operator.

fn ge(&self, other: &Rhs) -> bool

Tests greater than or equal to (for self and other) and is used by the >= operator.

impl StructuralPartialEq for DeviceFeature