feather_m0 0.20.3

#![no_std]

#[cfg(feature = "rt")]
pub use cortex_m_rt::entry;

pub use atsamd_hal as hal;
pub use hal::ehal;
pub use hal::pac;

use hal::clock::GenericClockController;
use hal::sercom::{
    i2c, spi,
    uart::{self, BaudMode, Oversampling},
};
use hal::time::Hertz;

#[cfg(feature = "usb")]
use hal::usb::{usb_device::bus::UsbBusAllocator, UsbBus};

hal::bsp_peripherals!(
    Sercom0 { UartSercom }
    Sercom3 { I2cSercom }
    Sercom4 { SpiSercom }
);

/// Definitions related to pins and pin aliases
pub mod pins {
    use super::hal;

    hal::bsp_pins!(
        PA03 {
            /// AREF pin - has 1uF capacitor to ground
            name: aref
        }
        PA02 {
            /// Analog pin 0.
            /// Can act as a true analog output as it has a DAC (which is not
            /// currently supported by this hal) as well as input.
            name: a0,
            aliases: {
                AlternateB: A0
            }
        }
        PB08 {
            /// Analog Pin 1
            name: a1
        }
        PB09 {
            /// Analog Pin 2
            name: a2
        }
        PA04 {
            /// Analog Pin 3
            name: a3
        }
        PA05 {
            /// Analog Pin 4
            name: a4
        }
        PB02 {
            /// Analog Pin 5
            name: a5
        }

        PA11 {
            /// Pin 0, rx
            name: d0
            aliases: {
                AlternateC: UartRx
            }
        }
        PA10 {
            /// Pin 1, tx
            name: d1
            aliases: {
                AlternateC: UartTx
            }
        }
        PA15 {
            /// Pin 5, PWM capable
            name: d5
            aliases: {
                AlternateE: D5Pwm
            }
        }
        PA20 {
            /// Pin 6, PWM capable
            name: d6
            aliases: {
                PushPullOutput: Ssd1306Dc
            }
        }
        PA07 {
            /// Pin 9, PWM capable.  Also analog input (A7)
            name: d9
            aliases: {
                PushPullOutput: Ssd1306Rst
            }
        }
        PA18 {
            /// Pin 10, PWM capable
            name: d10
        }
        PA16 {
            /// Pin 11, PWM capable
            name: d11
        }
        PA19 {
            /// Pin 12, PWM capable
            name: d12
        }
        PA17 {
            /// Pin 13, which is also attached to the red LED. PWM capable.
            name: d13
            aliases: {
                PushPullOutput: RedLed
            }
        }

        PA22 {
            /// The I2C data line
            name: sda
            aliases: {
                AlternateC: Sda
            }
        }
        PA23 {
            /// The I2C clock line
            name: scl
            aliases: {
                AlternateC: Scl
            }
        }

        PB11 {
            /// The SPI SCLK
            name: sclk
            aliases: {
                AlternateD: Sclk
            }
        }
        PB10 {
            /// The SPI MOSI
            name: mosi
            aliases: {
                AlternateD: Mosi
            }
        }
        PA12 {
            /// The SPI MISO
            name: miso
            aliases: {
                AlternateD: Miso
            }
        }

        PA24 {
            /// The USB D- pad
            name: usb_dm
            aliases: {
                AlternateG: UsbDm
            }
        }
        PA25 {
            /// The USB D+ pad
            name: usb_dp
            aliases: {
                AlternateG: UsbDp
            }
        }

        #[cfg(all(feature = "rfm", not(feature = "express"), not(feature = "winc")))]
        PA06 {
            /// SPI chip select for the RFM module
            name: rfm_cs
        }
        #[cfg(all(feature = "rfm", not(feature = "express"), not(feature = "adalogger"), not(feature = "winc")))]
        PA08 {
            /// Reset for the RFM module
            name: rfm_reset
        }
        #[cfg(all(feature = "rfm", not(feature = "express")))]
        PA09 {
            /// Interrupt from the RFM module
            name: rfm_irq
        }

        #[cfg(all(feature = "express", not(feature = "rfm"), not(feature = "winc")))]
        PA06 {
            /// Neopixel data
            name: neopixel
        }

        #[cfg(all(feature = "express", not(feature = "rfm")))]
        PA09 {
            /// SPI clock for the external flash
            name: flash_sclk
        }
        #[cfg(all(feature = "express", not(feature = "rfm"), not(feature = "adalogger"), not(feature = "winc")))]
        PA08 {
            /// SPI MOSI for the external flash
            name: flash_mosi
        }
        #[cfg(all(feature = "express", not(feature= "winc")))]
        PA14 {
            /// SPI MISO for the external flash
            name: flash_miso
        }
        #[cfg(feature = "express")]
        PA13 {
            /// SPI chip select for the external flash
            name: flash_cs
        }

        #[cfg(all(feature = "adalogger", not(feature = "rfm"), not(feature = "express"), not(feature = "winc")))]
        PA08 {
            /// SD card SPI chip select
            name: sd_cs
            aliases: {
                PushPullOutput: SdCs
            }
        },
        #[cfg(all(feature = "adalogger", not(feature = "rfm"), not(feature = "express") , not(feature = "winc")))]
        PA21 {
            /// SD card detect
            name: sd_cd
            aliases: {
                PullUpInput: SdCd
            }
        },

        #[cfg(all(feature = "winc", not(feature = "rfm"), not(feature = "express"), not(feature = "adalogger")))]
        PA08 {
            /// Reset for the WINC1500 module
            name: winc_rst
            aliases: {
                PushPullOutput: WincRst
            }
        },

        #[cfg(all(feature = "winc", not(feature= "express")))]
        PA14 {
            /// Enable for the WINC1500 module
            name: winc_ena
            aliases: {
                PushPullOutput: WincEna
            }
        }

        #[cfg(all(feature = "winc", not(feature = "adalogger")))]
        PA21 {
            /// Interrupt for the WINC1500 module
            name: winc_irq
            aliases: {
                PullUpInterrupt: WincIrq
            }
        },

        #[cfg(all(feature = "winc", not(feature = "rfm"), not(feature = "express")))]
        PA06 {
            /// SPI chip select for the WINC1500 module
            name: winc_cs
            aliases: {
                PushPullOutput: WincCs
            }
        },

    );
}
pub use pins::*;

/// SPI pads for the labelled SPI peripheral
///
/// You can use these pads with other, user-defined [`spi::Config`]urations.
pub type SpiPads = spi::Pads<SpiSercom, Miso, Mosi, Sclk>;

/// SPI master for the labelled SPI peripheral
///
/// This type implements [`FullDuplex<u8>`](ehal::spi::FullDuplex).
pub type Spi = spi::Spi<spi::Config<SpiPads>, spi::Duplex>;

/// Convenience for setting up the labelled SPI peripheral.
/// This powers up the SPI SERCOM and configures it for use as an
/// SPI Master in SPI Mode 0.
pub fn spi_master(
    clocks: &mut GenericClockController,
    baud: Hertz,
    sercom: SpiSercom,
    pm: &mut pac::Pm,
    sclk: impl Into<Sclk>,
    mosi: impl Into<Mosi>,
    miso: impl Into<Miso>,
) -> Spi {
    let gclk0 = clocks.gclk0();
    let clock = clocks.sercom4_core(&gclk0).unwrap();
    let freq = clock.freq();
    let (miso, mosi, sclk) = (miso.into(), mosi.into(), sclk.into());
    let pads = spi::Pads::default().data_in(miso).data_out(mosi).sclk(sclk);
    spi::Config::new(pm, sercom, pads, freq)
        .baud(baud)
        .spi_mode(spi::MODE_0)
        .enable()
}

/// I2C pads for the labelled I2C peripheral
///
/// You can use these pads with other, user-defined [`i2c::Config`]urations.
pub type I2cPads = i2c::Pads<I2cSercom, Sda, Scl>;

/// I2C master for the labelled I2C peripheral
///
/// This type implements [`Read`](ehal::blocking::i2c::Read),
/// [`Write`](ehal::blocking::i2c::Write) and
/// [`WriteRead`](ehal::blocking::i2c::WriteRead).
pub type I2c = i2c::I2c<i2c::Config<I2cPads>>;

/// Convenience for setting up the labelled SDA, SCL pins to
/// operate as an I2C master running at the specified frequency.
pub fn i2c_master(
    clocks: &mut GenericClockController,
    baud: impl Into<Hertz>,
    sercom: I2cSercom,
    pm: &mut pac::Pm,
    sda: impl Into<Sda>,
    scl: impl Into<Scl>,
) -> I2c {
    let gclk0 = clocks.gclk0();
    let clock = &clocks.sercom3_core(&gclk0).unwrap();
    let freq = clock.freq();
    let baud = baud.into();
    let pads = i2c::Pads::new(sda.into(), scl.into());
    i2c::Config::new(pm, sercom, pads, freq).baud(baud).enable()
}

/// UART pads for the labelled RX & TX pins
pub type UartPads = uart::Pads<UartSercom, UartRx, UartTx>;

/// UART device for the labelled RX & TX pins
pub type Uart = uart::Uart<uart::Config<UartPads>, uart::Duplex>;

/// Convenience for setting up the labelled RX, TX pins to
/// operate as a UART device running at the specified baud.
pub fn uart(
    clocks: &mut GenericClockController,
    baud: impl Into<Hertz>,
    sercom: UartSercom,
    pm: &mut pac::Pm,
    uart_rx: impl Into<UartRx>,
    uart_tx: impl Into<UartTx>,
) -> Uart {
    let gclk0 = clocks.gclk0();
    let clock = &clocks.sercom0_core(&gclk0).unwrap();
    let baud = baud.into();
    let pads = uart::Pads::default().rx(uart_rx.into()).tx(uart_tx.into());
    uart::Config::new(pm, sercom, pads, clock.freq())
        .baud(baud, BaudMode::Fractional(Oversampling::Bits16))
        .enable()
}

#[cfg(feature = "usb")]
/// Convenience function for setting up USB
pub fn usb_allocator(
    usb: pac::Usb,
    clocks: &mut GenericClockController,
    pm: &mut pac::Pm,
    dm: impl Into<UsbDm>,
    dp: impl Into<UsbDp>,
) -> UsbBusAllocator<UsbBus> {
    let gclk0 = clocks.gclk0();
    let clock = &clocks.usb(&gclk0).unwrap();
    let (dm, dp) = (dm.into(), dp.into());
    UsbBusAllocator::new(UsbBus::new(clock, pm, dm, dp, usb))
}