1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
//! Test the serial interface
//!
//! This example requires you to short (connect) the TX and RX pins.
//!
//! ```
//! #![deny(unsafe_code)]
//! #![deny(warnings)]
//! #![no_main]
//! #![no_std]
//!
//! extern crate cortex_m;
//! #[macro_use(entry, exception)]
//! extern crate cortex_m_rt as rt;
//! extern crate f3;
//! #[macro_use(block)]
//! extern crate nb;
//! extern crate panic_semihosting;
//!
//! use cortex_m::asm;
//! use f3::hal::prelude::*;
//! use f3::hal::serial::Serial;
//! use f3::hal::stm32f30x;
//! use rt::ExceptionFrame;
//!
//! entry!(main);
//!
//! fn main() -> ! {
//! let p = stm32f30x::Peripherals::take().unwrap();
//!
//! let mut flash = p.FLASH.constrain();
//! let mut rcc = p.RCC.constrain();
//! let mut gpioa = p.GPIOA.split(&mut rcc.ahb);
//! let mut gpiob = p.GPIOB.split(&mut rcc.ahb);
//!
//! // clock configuration using the default settings (all clocks run at 8 MHz)
//! let clocks = rcc.cfgr.freeze(&mut flash.acr);
//! // TRY this alternate clock configuration (clocks run at nearly the maximum frequency)
//! // let clocks = rcc.cfgr.sysclk(64.mhz()).pclk1(32.mhz()).freeze(&mut flash.acr);
//!
//! // The Serial API is highly generic
//! // TRY the commented out, different pin configurations
//! let tx = gpioa.pa9.into_af7(&mut gpioa.moder, &mut gpioa.afrh);
//! // let tx = gpiob.pb6.into_af7(&mut gpiob.moder, &mut gpiob.afrl);
//!
//! // let rx = gpioa.pa10.into_af7(&mut gpioa.moder, &mut gpioa.afrh);
//! let rx = gpiob.pb7.into_af7(&mut gpiob.moder, &mut gpiob.afrl);
//!
//! // TRY using a different USART peripheral here
//! let serial = Serial::usart1(p.USART1, (tx, rx), 9_600.bps(), clocks, &mut rcc.apb2);
//! let (mut tx, mut rx) = serial.split();
//!
//! let sent = b'X';
//!
//! // The `block!` macro makes an operation block until it finishes
//! // NOTE the error type is `!`
//! block!(tx.write(sent)).ok();
//!
//! let received = block!(rx.read()).unwrap();
//!
//! assert_eq!(received, sent);
//!
//! // if all goes well you should reach this breakpoint
//! asm::bkpt();
//!
//! loop {}
//! }
//!
//! exception!(HardFault, hard_fault);
//!
//! fn hard_fault(ef: &ExceptionFrame) -> ! {
//! panic!("{:#?}", ef);
//! }
//!
//! exception!(*, default_handler);
//!
//! fn default_handler(irqn: i16) {
//! panic!("Unhandled exception (IRQn = {})", irqn);
//! }
//! ```
// Auto-generated. Do not modify.