#[doc = "Register `CH%sCONF1` reader"]
pub struct R(crate::R<CHCONF1_SPEC>);
impl core::ops::Deref for R {
type Target = crate::R<CHCONF1_SPEC>;
#[inline(always)]
fn deref(&self) -> &Self::Target {
&self.0
}
}
impl From<crate::R<CHCONF1_SPEC>> for R {
#[inline(always)]
fn from(reader: crate::R<CHCONF1_SPEC>) -> Self {
R(reader)
}
}
#[doc = "Register `CH%sCONF1` writer"]
pub struct W(crate::W<CHCONF1_SPEC>);
impl core::ops::Deref for W {
type Target = crate::W<CHCONF1_SPEC>;
#[inline(always)]
fn deref(&self) -> &Self::Target {
&self.0
}
}
impl core::ops::DerefMut for W {
#[inline(always)]
fn deref_mut(&mut self) -> &mut Self::Target {
&mut self.0
}
}
impl From<crate::W<CHCONF1_SPEC>> for W {
#[inline(always)]
fn from(writer: crate::W<CHCONF1_SPEC>) -> Self {
W(writer)
}
}
#[doc = "Field `TX_START` reader - Set this bit to start sending data on CHANNEL%s."]
pub type TX_START_R = crate::BitReader<bool>;
#[doc = "Field `TX_START` writer - Set this bit to start sending data on CHANNEL%s."]
pub type TX_START_W<'a, const O: u8> = crate::BitWriter<'a, u32, CHCONF1_SPEC, bool, O>;
#[doc = "Field `RX_EN` reader - Set this bit to enable receiver to receive data on CHANNEL%s."]
pub type RX_EN_R = crate::BitReader<bool>;
#[doc = "Field `RX_EN` writer - Set this bit to enable receiver to receive data on CHANNEL%s."]
pub type RX_EN_W<'a, const O: u8> = crate::BitWriter<'a, u32, CHCONF1_SPEC, bool, O>;
#[doc = "Field `MEM_WR_RST` writer - Set this bit to reset write ram address for CHANNEL%s by accessing receiver."]
pub type MEM_WR_RST_W<'a, const O: u8> = crate::BitWriter<'a, u32, CHCONF1_SPEC, bool, O>;
#[doc = "Field `MEM_RD_RST` writer - Set this bit to reset read ram address for CHANNEL%s by accessing transmitter."]
pub type MEM_RD_RST_W<'a, const O: u8> = crate::BitWriter<'a, u32, CHCONF1_SPEC, bool, O>;
#[doc = "Field `APB_MEM_RST` writer - Set this bit to reset W/R ram address for CHANNEL%s by accessing apb fifo."]
pub type APB_MEM_RST_W<'a, const O: u8> = crate::BitWriter<'a, u32, CHCONF1_SPEC, bool, O>;
#[doc = "Field `MEM_OWNER` reader - This register marks the ownership of CHANNEL%s's ram block. 1'h1: Receiver is using the ram. 1'h0: Transmitter is using the ram."]
pub type MEM_OWNER_R = crate::BitReader<bool>;
#[doc = "Field `MEM_OWNER` writer - This register marks the ownership of CHANNEL%s's ram block. 1'h1: Receiver is using the ram. 1'h0: Transmitter is using the ram."]
pub type MEM_OWNER_W<'a, const O: u8> = crate::BitWriter<'a, u32, CHCONF1_SPEC, bool, O>;
#[doc = "Field `TX_CONTI_MODE` reader - Set this bit to restart transmission from the first data to the last data in CHANNEL%s."]
pub type TX_CONTI_MODE_R = crate::BitReader<bool>;
#[doc = "Field `TX_CONTI_MODE` writer - Set this bit to restart transmission from the first data to the last data in CHANNEL%s."]
pub type TX_CONTI_MODE_W<'a, const O: u8> = crate::BitWriter<'a, u32, CHCONF1_SPEC, bool, O>;
#[doc = "Field `RX_FILTER_EN` reader - This is the receive filter's enable bit for CHANNEL%s."]
pub type RX_FILTER_EN_R = crate::BitReader<bool>;
#[doc = "Field `RX_FILTER_EN` writer - This is the receive filter's enable bit for CHANNEL%s."]
pub type RX_FILTER_EN_W<'a, const O: u8> = crate::BitWriter<'a, u32, CHCONF1_SPEC, bool, O>;
#[doc = "Field `RX_FILTER_THRES` reader - Ignores the input pulse when its width is smaller than this register value in APB clock periods (in receive mode)."]
pub type RX_FILTER_THRES_R = crate::FieldReader<u8, u8>;
#[doc = "Field `RX_FILTER_THRES` writer - Ignores the input pulse when its width is smaller than this register value in APB clock periods (in receive mode)."]
pub type RX_FILTER_THRES_W<'a, const O: u8> =
crate::FieldWriter<'a, u32, CHCONF1_SPEC, u8, u8, 8, O>;
#[doc = "Field `CHK_RX_CARRIER_EN` reader - Set this bit to enable memory loop read mode when carrier modulation is enabled for channel %s."]
pub type CHK_RX_CARRIER_EN_R = crate::BitReader<bool>;
#[doc = "Field `CHK_RX_CARRIER_EN` writer - Set this bit to enable memory loop read mode when carrier modulation is enabled for channel %s."]
pub type CHK_RX_CARRIER_EN_W<'a, const O: u8> = crate::BitWriter<'a, u32, CHCONF1_SPEC, bool, O>;
#[doc = "Field `REF_ALWAYS_ON` reader - This bit is used to select the base clock for CHANNEL%s. 1'h1: clk_apb 1'h0:clk_ref"]
pub type REF_ALWAYS_ON_R = crate::BitReader<bool>;
#[doc = "Field `REF_ALWAYS_ON` writer - This bit is used to select the base clock for CHANNEL%s. 1'h1: clk_apb 1'h0:clk_ref"]
pub type REF_ALWAYS_ON_W<'a, const O: u8> = crate::BitWriter<'a, u32, CHCONF1_SPEC, bool, O>;
#[doc = "Field `IDLE_OUT_LV` reader - This bit configures the level of output signal in CHANNEL%s when the latter is in IDLE state."]
pub type IDLE_OUT_LV_R = crate::BitReader<bool>;
#[doc = "Field `IDLE_OUT_LV` writer - This bit configures the level of output signal in CHANNEL%s when the latter is in IDLE state."]
pub type IDLE_OUT_LV_W<'a, const O: u8> = crate::BitWriter<'a, u32, CHCONF1_SPEC, bool, O>;
#[doc = "Field `IDLE_OUT_EN` reader - This is the output enable-control bit for CHANNEL%s in IDLE state."]
pub type IDLE_OUT_EN_R = crate::BitReader<bool>;
#[doc = "Field `IDLE_OUT_EN` writer - This is the output enable-control bit for CHANNEL%s in IDLE state."]
pub type IDLE_OUT_EN_W<'a, const O: u8> = crate::BitWriter<'a, u32, CHCONF1_SPEC, bool, O>;
#[doc = "Field `TX_STOP` reader - Set this bit to stop the transmitter of CHANNEL%s sending data out."]
pub type TX_STOP_R = crate::BitReader<bool>;
#[doc = "Field `TX_STOP` writer - Set this bit to stop the transmitter of CHANNEL%s sending data out."]
pub type TX_STOP_W<'a, const O: u8> = crate::BitWriter<'a, u32, CHCONF1_SPEC, bool, O>;
impl R {
#[doc = "Bit 0 - Set this bit to start sending data on CHANNEL%s."]
#[inline(always)]
pub fn tx_start(&self) -> TX_START_R {
TX_START_R::new((self.bits & 1) != 0)
}
#[doc = "Bit 1 - Set this bit to enable receiver to receive data on CHANNEL%s."]
#[inline(always)]
pub fn rx_en(&self) -> RX_EN_R {
RX_EN_R::new(((self.bits >> 1) & 1) != 0)
}
#[doc = "Bit 5 - This register marks the ownership of CHANNEL%s's ram block. 1'h1: Receiver is using the ram. 1'h0: Transmitter is using the ram."]
#[inline(always)]
pub fn mem_owner(&self) -> MEM_OWNER_R {
MEM_OWNER_R::new(((self.bits >> 5) & 1) != 0)
}
#[doc = "Bit 6 - Set this bit to restart transmission from the first data to the last data in CHANNEL%s."]
#[inline(always)]
pub fn tx_conti_mode(&self) -> TX_CONTI_MODE_R {
TX_CONTI_MODE_R::new(((self.bits >> 6) & 1) != 0)
}
#[doc = "Bit 7 - This is the receive filter's enable bit for CHANNEL%s."]
#[inline(always)]
pub fn rx_filter_en(&self) -> RX_FILTER_EN_R {
RX_FILTER_EN_R::new(((self.bits >> 7) & 1) != 0)
}
#[doc = "Bits 8:15 - Ignores the input pulse when its width is smaller than this register value in APB clock periods (in receive mode)."]
#[inline(always)]
pub fn rx_filter_thres(&self) -> RX_FILTER_THRES_R {
RX_FILTER_THRES_R::new(((self.bits >> 8) & 0xff) as u8)
}
#[doc = "Bit 16 - Set this bit to enable memory loop read mode when carrier modulation is enabled for channel %s."]
#[inline(always)]
pub fn chk_rx_carrier_en(&self) -> CHK_RX_CARRIER_EN_R {
CHK_RX_CARRIER_EN_R::new(((self.bits >> 16) & 1) != 0)
}
#[doc = "Bit 17 - This bit is used to select the base clock for CHANNEL%s. 1'h1: clk_apb 1'h0:clk_ref"]
#[inline(always)]
pub fn ref_always_on(&self) -> REF_ALWAYS_ON_R {
REF_ALWAYS_ON_R::new(((self.bits >> 17) & 1) != 0)
}
#[doc = "Bit 18 - This bit configures the level of output signal in CHANNEL%s when the latter is in IDLE state."]
#[inline(always)]
pub fn idle_out_lv(&self) -> IDLE_OUT_LV_R {
IDLE_OUT_LV_R::new(((self.bits >> 18) & 1) != 0)
}
#[doc = "Bit 19 - This is the output enable-control bit for CHANNEL%s in IDLE state."]
#[inline(always)]
pub fn idle_out_en(&self) -> IDLE_OUT_EN_R {
IDLE_OUT_EN_R::new(((self.bits >> 19) & 1) != 0)
}
#[doc = "Bit 20 - Set this bit to stop the transmitter of CHANNEL%s sending data out."]
#[inline(always)]
pub fn tx_stop(&self) -> TX_STOP_R {
TX_STOP_R::new(((self.bits >> 20) & 1) != 0)
}
}
impl W {
#[doc = "Bit 0 - Set this bit to start sending data on CHANNEL%s."]
#[inline(always)]
#[must_use]
pub fn tx_start(&mut self) -> TX_START_W<0> {
TX_START_W::new(self)
}
#[doc = "Bit 1 - Set this bit to enable receiver to receive data on CHANNEL%s."]
#[inline(always)]
#[must_use]
pub fn rx_en(&mut self) -> RX_EN_W<1> {
RX_EN_W::new(self)
}
#[doc = "Bit 2 - Set this bit to reset write ram address for CHANNEL%s by accessing receiver."]
#[inline(always)]
#[must_use]
pub fn mem_wr_rst(&mut self) -> MEM_WR_RST_W<2> {
MEM_WR_RST_W::new(self)
}
#[doc = "Bit 3 - Set this bit to reset read ram address for CHANNEL%s by accessing transmitter."]
#[inline(always)]
#[must_use]
pub fn mem_rd_rst(&mut self) -> MEM_RD_RST_W<3> {
MEM_RD_RST_W::new(self)
}
#[doc = "Bit 4 - Set this bit to reset W/R ram address for CHANNEL%s by accessing apb fifo."]
#[inline(always)]
#[must_use]
pub fn apb_mem_rst(&mut self) -> APB_MEM_RST_W<4> {
APB_MEM_RST_W::new(self)
}
#[doc = "Bit 5 - This register marks the ownership of CHANNEL%s's ram block. 1'h1: Receiver is using the ram. 1'h0: Transmitter is using the ram."]
#[inline(always)]
#[must_use]
pub fn mem_owner(&mut self) -> MEM_OWNER_W<5> {
MEM_OWNER_W::new(self)
}
#[doc = "Bit 6 - Set this bit to restart transmission from the first data to the last data in CHANNEL%s."]
#[inline(always)]
#[must_use]
pub fn tx_conti_mode(&mut self) -> TX_CONTI_MODE_W<6> {
TX_CONTI_MODE_W::new(self)
}
#[doc = "Bit 7 - This is the receive filter's enable bit for CHANNEL%s."]
#[inline(always)]
#[must_use]
pub fn rx_filter_en(&mut self) -> RX_FILTER_EN_W<7> {
RX_FILTER_EN_W::new(self)
}
#[doc = "Bits 8:15 - Ignores the input pulse when its width is smaller than this register value in APB clock periods (in receive mode)."]
#[inline(always)]
#[must_use]
pub fn rx_filter_thres(&mut self) -> RX_FILTER_THRES_W<8> {
RX_FILTER_THRES_W::new(self)
}
#[doc = "Bit 16 - Set this bit to enable memory loop read mode when carrier modulation is enabled for channel %s."]
#[inline(always)]
#[must_use]
pub fn chk_rx_carrier_en(&mut self) -> CHK_RX_CARRIER_EN_W<16> {
CHK_RX_CARRIER_EN_W::new(self)
}
#[doc = "Bit 17 - This bit is used to select the base clock for CHANNEL%s. 1'h1: clk_apb 1'h0:clk_ref"]
#[inline(always)]
#[must_use]
pub fn ref_always_on(&mut self) -> REF_ALWAYS_ON_W<17> {
REF_ALWAYS_ON_W::new(self)
}
#[doc = "Bit 18 - This bit configures the level of output signal in CHANNEL%s when the latter is in IDLE state."]
#[inline(always)]
#[must_use]
pub fn idle_out_lv(&mut self) -> IDLE_OUT_LV_W<18> {
IDLE_OUT_LV_W::new(self)
}
#[doc = "Bit 19 - This is the output enable-control bit for CHANNEL%s in IDLE state."]
#[inline(always)]
#[must_use]
pub fn idle_out_en(&mut self) -> IDLE_OUT_EN_W<19> {
IDLE_OUT_EN_W::new(self)
}
#[doc = "Bit 20 - Set this bit to stop the transmitter of CHANNEL%s sending data out."]
#[inline(always)]
#[must_use]
pub fn tx_stop(&mut self) -> TX_STOP_W<20> {
TX_STOP_W::new(self)
}
#[doc = "Writes raw bits to the register."]
#[inline(always)]
pub unsafe fn bits(&mut self, bits: u32) -> &mut Self {
self.0.bits(bits);
self
}
}
#[doc = "Channel %s configure register 1\n\nThis register you can [`read`](crate::generic::Reg::read), [`write_with_zero`](crate::generic::Reg::write_with_zero), [`reset`](crate::generic::Reg::reset), [`write`](crate::generic::Reg::write), [`modify`](crate::generic::Reg::modify). See [API](https://docs.rs/svd2rust/#read--modify--write-api).\n\nFor information about available fields see [chconf1](index.html) module"]
pub struct CHCONF1_SPEC;
impl crate::RegisterSpec for CHCONF1_SPEC {
type Ux = u32;
}
#[doc = "`read()` method returns [chconf1::R](R) reader structure"]
impl crate::Readable for CHCONF1_SPEC {
type Reader = R;
}
#[doc = "`write(|w| ..)` method takes [chconf1::W](W) writer structure"]
impl crate::Writable for CHCONF1_SPEC {
type Writer = W;
const ZERO_TO_MODIFY_FIELDS_BITMAP: Self::Ux = 0;
const ONE_TO_MODIFY_FIELDS_BITMAP: Self::Ux = 0;
}
#[doc = "`reset()` method sets CH%sCONF1 to value 0x0f20"]
impl crate::Resettable for CHCONF1_SPEC {
const RESET_VALUE: Self::Ux = 0x0f20;
}