#[doc = "Register `RD_REPEAT_DATA0` reader"]
pub struct R(crate::R<RD_REPEAT_DATA0_SPEC>);
impl core::ops::Deref for R {
type Target = crate::R<RD_REPEAT_DATA0_SPEC>;
#[inline(always)]
fn deref(&self) -> &Self::Target {
&self.0
}
}
impl From<crate::R<RD_REPEAT_DATA0_SPEC>> for R {
#[inline(always)]
fn from(reader: crate::R<RD_REPEAT_DATA0_SPEC>) -> Self {
R(reader)
}
}
#[doc = "Field `RD_DIS` reader - Represents whether reading of individual eFuse block(block4~block10) is disabled or enabled. 1: disabled. 0: enabled."]
pub type RD_DIS_R = crate::FieldReader;
#[doc = "Field `SWAP_UART_SDIO_EN` reader - Represents whether pad of uart and sdio is swapped or not. 1: swapped. 0: not swapped."]
pub type SWAP_UART_SDIO_EN_R = crate::BitReader;
#[doc = "Field `DIS_ICACHE` reader - Represents whether icache is disabled or enabled. 1: disabled. 0: enabled."]
pub type DIS_ICACHE_R = crate::BitReader;
#[doc = "Field `DIS_USB_JTAG` reader - Represents whether the function of usb switch to jtag is disabled or enabled. 1: disabled. 0: enabled."]
pub type DIS_USB_JTAG_R = crate::BitReader;
#[doc = "Field `DIS_DOWNLOAD_ICACHE` reader - Represents whether icache is disabled or enabled in Download mode. 1: disabled. 0: enabled."]
pub type DIS_DOWNLOAD_ICACHE_R = crate::BitReader;
#[doc = "Field `DIS_USB_SERIAL_JTAG` reader - Represents whether USB-Serial-JTAG is disabled or enabled. 1: disabled. 0: enabled."]
pub type DIS_USB_SERIAL_JTAG_R = crate::BitReader;
#[doc = "Field `DIS_FORCE_DOWNLOAD` reader - Represents whether the function that forces chip into download mode is disabled or enabled. 1: disabled. 0: enabled."]
pub type DIS_FORCE_DOWNLOAD_R = crate::BitReader;
#[doc = "Field `SPI_DOWNLOAD_MSPI_DIS` reader - Represents whether SPI0 controller during boot_mode_download is disabled or enabled. 1: disabled. 0: enabled."]
pub type SPI_DOWNLOAD_MSPI_DIS_R = crate::BitReader;
#[doc = "Field `DIS_CAN` reader - Represents whether TWAI function is disabled or enabled. 1: disabled. 0: enabled."]
pub type DIS_CAN_R = crate::BitReader;
#[doc = "Field `JTAG_SEL_ENABLE` reader - Represents whether the selection between usb_to_jtag and pad_to_jtag through strapping gpio15 when both EFUSE_DIS_PAD_JTAG and EFUSE_DIS_USB_JTAG are equal to 0 is enabled or disabled. 1: enabled. 0: disabled."]
pub type JTAG_SEL_ENABLE_R = crate::BitReader;
#[doc = "Field `SOFT_DIS_JTAG` reader - Represents whether JTAG is disabled in soft way. Odd number: disabled. Even number: enabled."]
pub type SOFT_DIS_JTAG_R = crate::FieldReader;
#[doc = "Field `DIS_PAD_JTAG` reader - Represents whether JTAG is disabled in the hard way(permanently). 1: disabled. 0: enabled."]
pub type DIS_PAD_JTAG_R = crate::BitReader;
#[doc = "Field `DIS_DOWNLOAD_MANUAL_ENCRYPT` reader - Represents whether flash encrypt function is disabled or enabled(except in SPI boot mode). 1: disabled. 0: enabled."]
pub type DIS_DOWNLOAD_MANUAL_ENCRYPT_R = crate::BitReader;
#[doc = "Field `USB_DREFH` reader - Represents the single-end input threhold vrefh, 1.76 V to 2 V with step of 80 mV."]
pub type USB_DREFH_R = crate::FieldReader;
#[doc = "Field `USB_DREFL` reader - Represents the single-end input threhold vrefl, 1.76 V to 2 V with step of 80 mV."]
pub type USB_DREFL_R = crate::FieldReader;
#[doc = "Field `USB_EXCHG_PINS` reader - Represents whether the D+ and D- pins is exchanged. 1: exchanged. 0: not exchanged."]
pub type USB_EXCHG_PINS_R = crate::BitReader;
#[doc = "Field `VDD_SPI_AS_GPIO` reader - Represents whether vdd spi pin is functioned as gpio. 1: functioned. 0: not functioned."]
pub type VDD_SPI_AS_GPIO_R = crate::BitReader;
#[doc = "Field `RPT4_RESERVED0_2` reader - Reserved."]
pub type RPT4_RESERVED0_2_R = crate::FieldReader;
#[doc = "Field `RPT4_RESERVED0_1` reader - Reserved."]
pub type RPT4_RESERVED0_1_R = crate::BitReader;
#[doc = "Field `RPT4_RESERVED0_0` reader - Reserved."]
pub type RPT4_RESERVED0_0_R = crate::FieldReader;
impl R {
#[doc = "Bits 0:6 - Represents whether reading of individual eFuse block(block4~block10) is disabled or enabled. 1: disabled. 0: enabled."]
#[inline(always)]
pub fn rd_dis(&self) -> RD_DIS_R {
RD_DIS_R::new((self.bits & 0x7f) as u8)
}
#[doc = "Bit 7 - Represents whether pad of uart and sdio is swapped or not. 1: swapped. 0: not swapped."]
#[inline(always)]
pub fn swap_uart_sdio_en(&self) -> SWAP_UART_SDIO_EN_R {
SWAP_UART_SDIO_EN_R::new(((self.bits >> 7) & 1) != 0)
}
#[doc = "Bit 8 - Represents whether icache is disabled or enabled. 1: disabled. 0: enabled."]
#[inline(always)]
pub fn dis_icache(&self) -> DIS_ICACHE_R {
DIS_ICACHE_R::new(((self.bits >> 8) & 1) != 0)
}
#[doc = "Bit 9 - Represents whether the function of usb switch to jtag is disabled or enabled. 1: disabled. 0: enabled."]
#[inline(always)]
pub fn dis_usb_jtag(&self) -> DIS_USB_JTAG_R {
DIS_USB_JTAG_R::new(((self.bits >> 9) & 1) != 0)
}
#[doc = "Bit 10 - Represents whether icache is disabled or enabled in Download mode. 1: disabled. 0: enabled."]
#[inline(always)]
pub fn dis_download_icache(&self) -> DIS_DOWNLOAD_ICACHE_R {
DIS_DOWNLOAD_ICACHE_R::new(((self.bits >> 10) & 1) != 0)
}
#[doc = "Bit 11 - Represents whether USB-Serial-JTAG is disabled or enabled. 1: disabled. 0: enabled."]
#[inline(always)]
pub fn dis_usb_serial_jtag(&self) -> DIS_USB_SERIAL_JTAG_R {
DIS_USB_SERIAL_JTAG_R::new(((self.bits >> 11) & 1) != 0)
}
#[doc = "Bit 12 - Represents whether the function that forces chip into download mode is disabled or enabled. 1: disabled. 0: enabled."]
#[inline(always)]
pub fn dis_force_download(&self) -> DIS_FORCE_DOWNLOAD_R {
DIS_FORCE_DOWNLOAD_R::new(((self.bits >> 12) & 1) != 0)
}
#[doc = "Bit 13 - Represents whether SPI0 controller during boot_mode_download is disabled or enabled. 1: disabled. 0: enabled."]
#[inline(always)]
pub fn spi_download_mspi_dis(&self) -> SPI_DOWNLOAD_MSPI_DIS_R {
SPI_DOWNLOAD_MSPI_DIS_R::new(((self.bits >> 13) & 1) != 0)
}
#[doc = "Bit 14 - Represents whether TWAI function is disabled or enabled. 1: disabled. 0: enabled."]
#[inline(always)]
pub fn dis_can(&self) -> DIS_CAN_R {
DIS_CAN_R::new(((self.bits >> 14) & 1) != 0)
}
#[doc = "Bit 15 - Represents whether the selection between usb_to_jtag and pad_to_jtag through strapping gpio15 when both EFUSE_DIS_PAD_JTAG and EFUSE_DIS_USB_JTAG are equal to 0 is enabled or disabled. 1: enabled. 0: disabled."]
#[inline(always)]
pub fn jtag_sel_enable(&self) -> JTAG_SEL_ENABLE_R {
JTAG_SEL_ENABLE_R::new(((self.bits >> 15) & 1) != 0)
}
#[doc = "Bits 16:18 - Represents whether JTAG is disabled in soft way. Odd number: disabled. Even number: enabled."]
#[inline(always)]
pub fn soft_dis_jtag(&self) -> SOFT_DIS_JTAG_R {
SOFT_DIS_JTAG_R::new(((self.bits >> 16) & 7) as u8)
}
#[doc = "Bit 19 - Represents whether JTAG is disabled in the hard way(permanently). 1: disabled. 0: enabled."]
#[inline(always)]
pub fn dis_pad_jtag(&self) -> DIS_PAD_JTAG_R {
DIS_PAD_JTAG_R::new(((self.bits >> 19) & 1) != 0)
}
#[doc = "Bit 20 - Represents whether flash encrypt function is disabled or enabled(except in SPI boot mode). 1: disabled. 0: enabled."]
#[inline(always)]
pub fn dis_download_manual_encrypt(&self) -> DIS_DOWNLOAD_MANUAL_ENCRYPT_R {
DIS_DOWNLOAD_MANUAL_ENCRYPT_R::new(((self.bits >> 20) & 1) != 0)
}
#[doc = "Bits 21:22 - Represents the single-end input threhold vrefh, 1.76 V to 2 V with step of 80 mV."]
#[inline(always)]
pub fn usb_drefh(&self) -> USB_DREFH_R {
USB_DREFH_R::new(((self.bits >> 21) & 3) as u8)
}
#[doc = "Bits 23:24 - Represents the single-end input threhold vrefl, 1.76 V to 2 V with step of 80 mV."]
#[inline(always)]
pub fn usb_drefl(&self) -> USB_DREFL_R {
USB_DREFL_R::new(((self.bits >> 23) & 3) as u8)
}
#[doc = "Bit 25 - Represents whether the D+ and D- pins is exchanged. 1: exchanged. 0: not exchanged."]
#[inline(always)]
pub fn usb_exchg_pins(&self) -> USB_EXCHG_PINS_R {
USB_EXCHG_PINS_R::new(((self.bits >> 25) & 1) != 0)
}
#[doc = "Bit 26 - Represents whether vdd spi pin is functioned as gpio. 1: functioned. 0: not functioned."]
#[inline(always)]
pub fn vdd_spi_as_gpio(&self) -> VDD_SPI_AS_GPIO_R {
VDD_SPI_AS_GPIO_R::new(((self.bits >> 26) & 1) != 0)
}
#[doc = "Bits 27:28 - Reserved."]
#[inline(always)]
pub fn rpt4_reserved0_2(&self) -> RPT4_RESERVED0_2_R {
RPT4_RESERVED0_2_R::new(((self.bits >> 27) & 3) as u8)
}
#[doc = "Bit 29 - Reserved."]
#[inline(always)]
pub fn rpt4_reserved0_1(&self) -> RPT4_RESERVED0_1_R {
RPT4_RESERVED0_1_R::new(((self.bits >> 29) & 1) != 0)
}
#[doc = "Bits 30:31 - Reserved."]
#[inline(always)]
pub fn rpt4_reserved0_0(&self) -> RPT4_RESERVED0_0_R {
RPT4_RESERVED0_0_R::new(((self.bits >> 30) & 3) as u8)
}
}
#[cfg(feature = "impl-register-debug")]
impl core::fmt::Debug for R {
fn fmt(&self, f: &mut core::fmt::Formatter) -> core::fmt::Result {
f.debug_struct("RD_REPEAT_DATA0")
.field("rd_dis", &format_args!("{}", self.rd_dis().bits()))
.field(
"swap_uart_sdio_en",
&format_args!("{}", self.swap_uart_sdio_en().bit()),
)
.field("dis_icache", &format_args!("{}", self.dis_icache().bit()))
.field(
"dis_usb_jtag",
&format_args!("{}", self.dis_usb_jtag().bit()),
)
.field(
"dis_download_icache",
&format_args!("{}", self.dis_download_icache().bit()),
)
.field(
"dis_usb_serial_jtag",
&format_args!("{}", self.dis_usb_serial_jtag().bit()),
)
.field(
"dis_force_download",
&format_args!("{}", self.dis_force_download().bit()),
)
.field(
"spi_download_mspi_dis",
&format_args!("{}", self.spi_download_mspi_dis().bit()),
)
.field("dis_can", &format_args!("{}", self.dis_can().bit()))
.field(
"jtag_sel_enable",
&format_args!("{}", self.jtag_sel_enable().bit()),
)
.field(
"soft_dis_jtag",
&format_args!("{}", self.soft_dis_jtag().bits()),
)
.field(
"dis_pad_jtag",
&format_args!("{}", self.dis_pad_jtag().bit()),
)
.field(
"dis_download_manual_encrypt",
&format_args!("{}", self.dis_download_manual_encrypt().bit()),
)
.field("usb_drefh", &format_args!("{}", self.usb_drefh().bits()))
.field("usb_drefl", &format_args!("{}", self.usb_drefl().bits()))
.field(
"usb_exchg_pins",
&format_args!("{}", self.usb_exchg_pins().bit()),
)
.field(
"vdd_spi_as_gpio",
&format_args!("{}", self.vdd_spi_as_gpio().bit()),
)
.field(
"rpt4_reserved0_2",
&format_args!("{}", self.rpt4_reserved0_2().bits()),
)
.field(
"rpt4_reserved0_1",
&format_args!("{}", self.rpt4_reserved0_1().bit()),
)
.field(
"rpt4_reserved0_0",
&format_args!("{}", self.rpt4_reserved0_0().bits()),
)
.finish()
}
}
#[cfg(feature = "impl-register-debug")]
impl core::fmt::Debug for crate::generic::Reg<RD_REPEAT_DATA0_SPEC> {
fn fmt(&self, f: &mut core::fmt::Formatter<'_>) -> core::fmt::Result {
self.read().fmt(f)
}
}
#[doc = "BLOCK0 data register 1.\n\nThis register you can [`read`](crate::generic::Reg::read). See [API](https://docs.rs/svd2rust/#read--modify--write-api).\n\nFor information about available fields see [rd_repeat_data0](index.html) module"]
pub struct RD_REPEAT_DATA0_SPEC;
impl crate::RegisterSpec for RD_REPEAT_DATA0_SPEC {
type Ux = u32;
}
#[doc = "`read()` method returns [rd_repeat_data0::R](R) reader structure"]
impl crate::Readable for RD_REPEAT_DATA0_SPEC {
type Reader = R;
}
#[doc = "`reset()` method sets RD_REPEAT_DATA0 to value 0"]
impl crate::Resettable for RD_REPEAT_DATA0_SPEC {
const RESET_VALUE: Self::Ux = 0;
}